COOLWORKS CRSF-18A1 18 Inch High Velocity Pedestal Fan Instruction Manual
- June 4, 2024
- COOLWORKS
Table of Contents
COOLWORKS CRSF-18A1 18 Inch High Velocity Pedestal Fan
Technical Specifications
Model : CRSF-18A1
Rated Voltage : 120 V
Rated Frequency : 60 Hz
Rated Power : 70 W
General Safety Rules
Read and save these instructions.
- Do not connect the fan to the power supply until the fan is fully assembled.
- Do not connect to any power supply other than 110V/60Hz.
- Never operate the fan if it has damaged or worn parts. It should be returned to the manufacturer, service agent or a similarly qualified person for repair in order to avoid a hazard.
- Always position the fan on a stable& level surface.
- Do not spray anything into the fan.
- Do not use the fan near flammable areas or substances.
- To reduce the risk of electric shock, do not remove any screws when the fan is plugged into the supply mains.
- Do not insert fingers or other objects through the fan grills.
- Do not remain in the direct wind path of the fan for long periods of time.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- The appliance is for indoor use only.
- Keep the appliance and its cord out of reach of children.
DISPOSAL
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
Main Parts
- A Front grill
- B Blade
- C Screws
- D Rear grill
- E Motor
- F Oscillating knob
- G Switch
- H Supply cord with plug
- I Extendable shaft
- J Height adjustable nut
- K Main shaft
- L Base cover
- M Screw & nuts
- N Base
Assembly Steps
- Assemble main shaft (K) on the base (N) and fasten four screws & nuts (M). Please see “STEP 1”.
- Loosen the firm screw, pull out the extendable shaft (I) from the main shaft (K), then fasten the screw from the neck of the motor (E) on the extendable shaft (I). Please see “STEP 2”.
- Put the rear grill (D) onto the front panel of the motor and fasten it with four screws. Please see “STEP 3”
- Put the blade (B) onto the motor shaft with the screw to fasten it. Please see “STEP 4”.
- Put the front grill (A) onto the rear grill (D), then secure both grills together with the grill clips on the outer edge of the front grill. Please see “STEP 5”.
Operating Instructions
Once the fan has been completely assembled, you can now plug it into a mains
socket. Turn the power on to the mains socket and then switch on the fan by
turning the button of the rotatory switch to any of the three speeds ‘1’, ‘2’,
or ‘3’ on the control panel (‘3’ is the fastest speed). Button ‘0’ switches
the fan ‘off’.
NOTE: Before inserting the plug into an electrical outlet, check if the
voltage & frequency on the data plate match the local voltage & frequency.
To make the fan oscillate (rotate from side to side), push down the
oscillating knob (F) Iocated on the top of the motor housing (E). To stop
oscillation, pull the button up.
To adjust the height of the fan, release the height adjustable nut (J), extend
the shaft to the desired height and re-tighten it.
Maintenance
- Ensure that the fan is switched off from the supply mains before removing the grills.
- Unplug the appliance from the power before servicing and cleaning.
- Clean your appliance with a slightly damp cloth and dry it up with a dry cloth.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Warranty
Your Coolworks fan has warranty against defects in materials and workmanship for a period of one (1) year from the date of original purchase. Please keep your proof of purchase (receipt) for any warranty claims. Warranty does not cover wear and tear, and damages arisen from misuse or use not in accordance with the product instructions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>