GNMN V7 Sports Wireless Headphones User Manual

GNMN V7 Sports Wireless Headphones

Product Information

V7 Sports Wireless Headphones

Packing List

• Charging Case x1
• Ear Tips x3
• User Manual x1
• USB-C Cable x1

Specifications

Model Name| FCC ID| Bluetooth Version| Support| Transmission Range| Input| Charging Port| Music Time| Phone Call Time| Charging Time| Headphones Battery Capacity| Charging Case Battery Capacity
---|---|---|---|---|---|---|---|---|---|---|---
V7| 2A8TA-V7| V5.3| A2DP/HFP/AVRCP/SPP/PBAP/BDR/BLE| 33 feet Max (without obstacle)| DC 5V 0.5A| Type-C| 8H| 6H| About 2H| 50mAh| 3.7V 500mAh / 1.85Wh

• Model Name: V7
• FCC ID: 2A8TA-V7
• Bluetooth Version: V5.3
• Support: A2DP/HFP/AVRCP/SPP/PBAP/BDR/BLE
• Transmission Range: 33feet Max (without obstacle)
• Input: DC 5V 0.5A
• Charging Port: Type-C
• Music Time: 8H
• Phone Call Time: 6H
• Charging Time: about 2H
• Headphones Battery Capacity: 50mAh
• Charging Case Battery Capacity: 3.7V 500mAh / 1.85Wh

Product Usage Instructions

Product Overview

• Charging Case Power Display
• Earphones Charging Status
• Flexible Ear Hook
• Charging Contact
• Type-C Charging Port
• Touch Control Area
• Earphone LED Light
• Ear Tips

Caution:

1. Please remove the protective film before use, otherwise, the headphone will not be able to charge. To remove the protective film, tear it off.
2. Choose suitable ear tips and wear them correctly to enhance sound quality.
3. If the headphones can’t be charged, clean the magnet charging contact on the earbud and charging pin on the charging case with alcohol wipes.
4. If the sound becomes low, clean the protective grille of both earbuds to make the sound louder.

How to Charge?

Charge by USB-C cable:

1. Place earbuds into the charging case properly.
2. Use the included USB-C charging cable to connect the charging case.
3. Plug the other end of the cable into a power supply with a 5V/1A adapter (not included).
4. The earbuds will start charging.

(* The USB-C charging cable is in the black paper box.)

Note:

1. If the earbud’s battery is lower than 10% (and the voltage is below 3.4V), you will hear a voice prompt “battery low” three times and then power off in turns.
2. The fully charged charging case can recharge the twin earbuds for 2-3 times without being plugged into a power supply.

LED Power Display:

• Show the remaining battery percentage of the charging case from 0-100. 0 means the charging case need charging while 100 means the charging case is fully charged.
• The earbud’s LED light: Red light up means being charged, Red light go off means fully charged.

Power On/Off & Pairing:

Automatically Power On/Off & Pairing:

1. Prior to first use (or not in use for a long time), please charge both earbuds and charging case fully.

2. Take twin earbuds out of the charging case, they will automatically power on and enter pairing mode.

3. Activate the Bluetooth setting on your phone, search and connect to V7. Note: If the earbuds are not connected to your device over 5 minutes, the earbuds will power off automatically.

4. Put the earbuds back into the charging case, they will disconnect and power off automatically.

Manually Power On/Off:

• If the earbud is out of the charging case and power off, then press and hold it for 2s, it will power on.
• To disconnect the Bluetooth with your device, press and hold either earbud for 5s, both earbuds will power off at the same time.

For Second Time Use:
If the headphones have already connected with your device, and the Bluetooth setting of this device is on, in the second time using, when you take out the earbuds from the charging case, they will connect with your device automatically.

Pair with Other Device
V7 Sports Headphones Bluetooth has memory function, it usually auto connects with the last paired device. Thus, if you want to pair them with other device, you should disconnect “V7” from the last paired device, AND forget the pairing record on the last device. Then try to connect it to a new device, it should work properly.

Mono Mode (Only Left/Right Earbud is being Used)
You can use one earbud alone, leave another earbud in the charging case.

• When in Dual mode, put one earbud into the charging case.
• Or only take one earbud out of the charging case, then search & connect “V7” on your device.

Factory Restore Setting

When should I reset?

• When only one side play music.
• When you can’t find “V7” on the device.
• When both earbuds fail to pair with each other or occur connection related issues.

How to reset？

• Delete “V7” record from the Bluetooth menu on your device and deactivate the Bluetooth setting.
• Make sure the charging case has power or being plugged into a power supply.
• Insert both earbuds into the charging case to get charged. Press and hold both earbuds for 8 secs at the same time to clean the pairing record with the last device.
• (* During this period, both earbuds’ LED will flash Red & Blue light once, then turn to Red light to get charge again.)
• Now turn on the Bluetooth setting on your device, search and connect the earbuds, they will work properly.

Note : If it still doesn’t work, please repeat the steps to try again.

Multi-Function Operations

For Call

Answer/End Call| Quick Double- Tap L/R earbud
Reject Call| Long Press 2s on L/R earbud
Voice Assistance

Siri| Quick Triple- Tap on L/R earbud

(* Must in non-music mode or standby mode)

Music Mode

Play/Pause| Quick Double- Click on L/R earbud
Next Song| Quick Triple- Click on R earbud
Previous Song| Quick Triple- Click on L earbud
Volume+| Long Press & Hold on R earbud
__   Volume –| Long Press & Hold on L earbud

(* ln single mode, R Earbud only support next song and Volume+, L Earbud only support previous song and Volume-)

How to sync volume on Android?

To protect users from potential hearing damage, Android’s limit on max volume is quite low for Bluetooth audio devices. lf you feel the volume is too low, please access developer options and enable absolute volume, so you’ll be able to max the volume at your own volition and to the full capabilities of your Bluetooth earphones.

(Scan this QR code to watch a video to learn more details.)

Find Build Number Firstly

• Android 4.1 and lower: the Developer options screen is available by default.
• Android 4.2 and higher : the Developer options in Android phones are hidden, you must enable this screen through Build Number.
• Android 7.1 and lower : Settings > About Phone > Build Number Android 8.0.0 and Android 8.1.0: Settings > System > About Phone > Build Number
• Android 9 and higher: Settings > About Phone > Build Number

Enable Developer Options

Locate the Build number and tap it about 7 times in succession to enable Developer options. You may also have to tap in your PIN for verification. Once developer options are activated, you will see a message that reads “You are now a developer”. Go back to the Settings pane, search Developer options as an entry. At the top of the Developer options screen, you can toggle the options as figure 1.

Enable Absolute Volume
Scroll down until you reach the Networking section. Once there, enable (toggle ON) the absolute volume options as figure 2. Note: These options in the figure 2 may be different from the device you’re using. Typically, the choices depend on the type and model of the device you are working with.

Customer Service

• Email : support@gnmn.tech
• WhatsApp: (+86) 1392 3490 475
• Web: www.gnmn.tech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>