Neomounts FL15-650WH1 Tablet Stand Instruction Manual
- June 12, 2024
- Neomounts
Table of Contents
Neomounts FL15-650WH1 Tablet Stand
Product Information
The FL15-650WH1 is a wall-mounted tablet holder designed to securely hold tablets of various sizes. It comes with a set of parts and tools required for installation.
DIMENSION
Parts Included
- A. (x1)
- B. (x1)
- C. (x1)
- D. (x1)
- E. (x1)
- F. (x1)
- G. (x1)
- H. (x1)
- J. (x1)a
- K. (x4)
- L. M4x12 (x4)
- M. M5x6 (x4)
- N. M8x20 (x4)
- Q. (x1)
- R. 4mm (x1)
- S. 5mm (x1)
- O. (x2)
- P. (x2)
Compatible Tablet Panels
- Panel 1: For 9,7 iPad 5/6, iPad Air 1/2 & iPad Pro (Gen 1)
- Panel 2: For 10,2 iPad 7/8/9 & 10,5 iPad Air 3, iPad Pro (Gen 2)
- Panel 3: For 11 iPad Pro (Gen 3/4/5) & 10,9 iPad Air 4
- Panel 4: For 10,4 Samsung Galaxy Tab A7
- Panel 5: For 10,1 Samsung Galaxy Tab A
- Panel 6: For 10,4 Samsung Galaxy Tab S6
Product Usage Instructions
-
Step 1:
Attach the adhesive pads (O) to the bottom of the base.
-
Step 2:
Route the cable and attach the pole (J) to the base.
-
Step 3A:
Install the mount on a concrete brick floor with a minimum height of 55mm (2.2 inches).
-
Step 3B:
Make sure the mount is properly aligned and secured on the floor.
-
Step 4:
Attach the holder (Q) to the pole and unlock it.
-
Step 5:
Remove the cover and place the tablet in the holder.
Note:
Remove any foam parts before installation.
-
Step 6:
Attach the compatible tablet panel to the holder using 4 screws (L). Adjust the clamps for proper alignment and placement of the tablet before fully tightening the screws. The panel number is indicated on the panel itself .
-
Step 7:
The installation is now complete. Ensure that the tablet is securely held in the holder and adjust the viewing angle as desired.
CAUTION
- To ensure safety, please read this manual carefully before installation and follow the instructions. Store this manual in a secure place for future reference.
- The manufacturer shall not be legally responsible for any equipment damage or personal injury caused by incorrect installation or operation other than that covered in this manual.
- The mount is designed for easy installation and removal. The manufacturer shall not be liable for damage to equipment or personal injuries arising out of human factors or acts of nature, such as earthquake or typhoon.
- It is recommended that the mount be installed by qualified personnel only.
- At least two persons are needed to install or remove the product to avoid hazard of falling objects.
- Please carefully inspect the area where the mount is to be installed:
- Avoid places that are subject to high temperatures, humidity or contact with water.
- Do not install the product near air conditioning vents or areas with excess dust and fumes.
- Only install on vertical walls and avoid slanted surfaces.
- Do not install in places subject to any shock or vibration.
- Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when viewing the display panel.
- Maintain sufficient space around the display to ensure adequate ventilation.
- To ensure safe installation, first check the structure of the wall, ceiling or floor and select a secure mounting location.
- The wall, ceiling or floor should be strong enough to sustain a weight of at least four times of the display and mount combined. The mounting location must be able to withstand earhquake or other strong shock.
- Do not modify any accessories or use broken parts. Contact your dealer with any questions.
- Tighten all saews (do not exert excessive force to avoid breaking the screw or damaging its thread).
- Drill holes and bolts will be left in the wall, ceiling or floor once the display and bracket are removed. Stains may occur after extended use.
- Since the manufacturer has no way to control the wall, ceiling or floor type and installation of the mount, the warranty of the product shall only cover the body of the mount. The warranty period of the product is 5 years.
- Please consult the English language manual for any dispute on conditions.