Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco Installation Guide

June 12, 2024
Stinger

stinger logo TXFBB12

Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford
Bronco 12” SWING GATE MOUNTED
SUBWOOFER ENCLOSURE
FOR FORD BRONCO
INSTALLATION GUIDE

TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco

NOTE! Read this installation guide thoroughly before disassembling or modifying the vehicle. Installation of this product requires technical skill, experience and specialized tools. If in doubt, it’s recommended to have it professionally installed by an authorized Stinger or AudioControl Dealer.

A video installation guide is available at:

https://stingerelectronics.com/products/txfbb12

Limited Warranty

Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.
INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by that country’s Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that country’s reseller for information.

INSTALLATION NOTES

  • For models equipped with a factory subwoofer, unplugging the factory subwoofer is recommended.
  • Some installation steps are more easily completed with a second person.
  • Speaker wire is required before the enclosure is mounted.
  • Recommended amplifier rating: 400-800 watts @ 2ohms.
  • Do not power up until inside contents are removed.

GETTING STARTED

Remove the four Philips screws from the speaker and remove the speaker.
Set speaker and screws in a safe place.

Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford
Bronco - GETTING STARTEDRemove contents from inside the enclosure.
Open the hardware pack and confirm hardware quantities and tools required using the guide on the following pages.

RECOMMENDED TOOLS

2 Philips Screwdriver

5mm Allen Wrench
14mm Wrench
10mm Socket
Ratchet
Socket Extension| 9mm Drill Bit (Included)
Drill
Center Punch
Hammer
Tape
Wire Strippers| Scissors
Rivet Nut Setter (Optional)
---|---|---

HARDWARE

Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford
Bronco - HARDWARE NOTE: Hardware images not to scale. There will be hardware left over depending on the installation

INSTALLATION

  1. Using scissors or a straight edge and utility knife, cut out the template along the dashed lines.  

  2. Position the template on the on the inside of the swing gate using the plastic trim panel as a guide as shown.
    Align the left and right cross-hairs on the template to the register marks on the trim panel (1). Verify the template is straight by confirming the horizontal line on the template (2) follows the horizontal groove on the plastic trim panel.
    Once aligned, securley tape the template to the swing gate.Stinger TXFBB12
12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco -
template

  3. Using a center punch, mark the four mounting locations on the template.
    Remove the template and drill pilot holes at the four locations.
    CAUTION: To prevent the drill bit from hitting the outer side of the swing gate, wrap a significantamount of tape around the drill bit leaving only ½” of the bit exposed.
    Drill 9mm holes at the four marked locations.Stinger TXFBB12 12 Inch Swing
Gate Mounted Subwoofer Enclosure for Ford Bronco -
mounting

  4. Remove the swing gate trim panel using a nylon panel tool or similar to release the retaining clips (1) along the bottom, then swing up (2) to release the locking tabs along the top.Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco - swing

  5. If a rivet nut setter is not available, follow the directions below for each of the four holes:
    A. Insert a R1 rivet nut into the hole.
    B. Slide an W2 metal washer, a N1 spacer nut and a W4 tooth lock washer onto one of the B3 bolts.
    C. Hand thread the bolt into the rivet nut until it is hand tight.
    D. Using a 14mm wrench to hold the spacer nut, start tightening the bolt with a 10mm socket.
    Ensure the the rivet nut remains  fully inserted and flat against the panel surface while tightening.
    The wrench and spacer nut should be held in place; do not rotate.
    The rivet nut takes approximately 12-13 quarter turns to propery seat.
    The bolt will get harder to turn when the rivet nut is seated.
    E. Once installed, loosen and remove the 10mm bolt while continuing to hold the spacer nut in place with the wrench.
    NOTE: After installing the first rivet nut, ensure the side of the spacer nut that was positioned against the tooth lock washer is the same for the remaining installations.
    There are two bolts, spacer nuts and washers provided in the event they are needed.
    TIP: Having a second person hold the wrench in place and using two hands to tighten with the ratchet will allow you to apply more forward pressure while tightening, keeping the insert flush against the panel.Stinger TXFBB12
12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco -
washer

  6. In the two lower threaded inserts, install L1 brackets using B2 allen bolts.
    Apply the L2 Foam Bracket Pads to the brackets.Stinger TXFBB12 12 Inch Swing
Gate Mounted Subwoofer Enclosure for Ford Bronco -
threaded

  7. Run a suitable length of speakerwire into the swing gate followingthe factory wire harness.
    Connect the speaker wire to the terminals. Positve (+) is Red and Negative (-) is Black. Route the speaker wire in the channel.Stinger TXFBB12 12 Inch
Swing Gate Mounted Subwoofer Enclosure for Ford Bronco -
length

  8. Align the speaker enclosure on  the L Brackets. Loosley install the indicated hardware into the upper mounting holes from inside the enclosure.
    Install the two B2 Allen Head Bolts through the L Brackets and into the bottom of the enclosure.
    Once all the bolts are threaded, tighten all hardware.Stinger TXFBB12 12
Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco - Figure
1

  9. A. Place the sheet of poly-fill inside the enclosure along the back and side areas.
    B. Connect the speaker leads inside the enclosure to either of the speaker terminals on the speaker. Positve (+) is Red and Negative (-) is Black.
    NOTE: Ensure the pre-installed speaker terminal jumper wires stay connected when connecting the wires to the speaker terminal.
    C. Align the speaker and install eight P1 screws securing the speaker. Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford
Bronco - sheet

SPECIFICATIONS

Model Number TXFBBI2
Speaker Model SPC-12S2
Subwoofer Size 12″
Voice Coil Single 2 ohm
DC Resistance (Re) 2 ohm
Sensitivity 1W/M (SPL) 87 dB
Frequency Response 20Hz – 250Hz
RMS Power 400 watts
Speaker Displacement 0.06 cu ft / 1.82 Ltr
Speaker Weight 12.5 lbs
Enclosure Specifications
Internal Volume 0.706 cu ft. / 19.99 Ltr
Enclosure Weight 16.25 lbs
Height 17in / 43.2cm
Width 27.5in / 69.9cm
Depth 4.6in / 11.7cm
Depth (with Speaker & Grill) 5.8in / 14.7cm

Height
17in / 43.2cm
Width
27.5in / 69.9cm
Depth
4.6in / 11.7cm

Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford
Bronco - swing 2

Stinger is a Power Brand of AAMP Global
15500 Lightwave, Clearwater, Florida 33760
Phone: 888-228-5560

Technical Support
Phone: 727-592-5991
Email: support@stingerelectronics.com
Chat: stingerelectronics.com
Stinger and the Stinger logo are trademarks or registered trademarks of AAMP Global in the United States and other countries.

stinger logo © 2021-2023 AAMP Global. All rights reserved.
IG-TXFBB12 REV 011923

Documents / Resources

| Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco [pdf] Installation Guide
TXFBB12, TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco, 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco, TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure, 12 Inch Swing Gate Mounted Subwoofer Enclosure, Swing Gate Mounted Subwoofer Enclosure, Gate Mounted Subwoofer Enclosure, Subwoofer Enclosure, Enclosure
---|---
| Stinger TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco [pdf] Installation Guide
TXFBB12, TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco, 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco, TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure, 12 Inch Swing Gate Mounted Subwoofer Enclosure, Swing Gate Mounted Subwoofer Enclosure, Gate Mounted Subwoofer Enclosure, Subwoofer Enclosure, Enclosure

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Stinger User Manuals

Related Manuals