Rowley I-1BBMOT2528 Roller Shade Motorized System Instruction Manual

Rowley I-1BBMOT2528 Roller Shade Motorized System Instruction Manual

INTRODUCTION

The Roller Shade Motorized System is used to electronically control the shade using a motor and remote control. The total allowable weight will depend on the motor selected (see the chart below for allowable shade weights). By using a remote control or the smart phone app the operator can raise and lower the shade smoothly and precisely. Figure 1 shows an assembled roller shade with motor and end brackets.

The Roller Shade can be mounted either inside or outside the window casing. For an inside mount, mount the brackets as close to the window as possible, yet have enough space for the shade fabric when completely rolled up.

The shade can be regular wind or reverse wind as shown below in Figure 2.

Figure 2. Side view on the top portion of the window

ALLOWABLE SHADE WEIGHTS

Tubular Motor Item #| Motor Type| Tube Dia.| Maximum Shade Size| Minimum Roller Shade Width/Roller Tube Length| Minimum Roman Shade Width/ Dustboard Length| Maximum Shade Weight
---|---|---|---|---|---|---
RTM5VL25S| Battery| 1 1/4″| 84″ x 84″| 22″| 23 1/2″| 15.5 lbs.
1 1/2″| 84″ x 84″| 22″| 23 1/2″| 13.0 lbs.
RTM5VL25| Battery| 1 1/4″| 84″ x 84″| 25″| 26 1/2″| 15.5 lbs.
1 1/2″| 84″ x 84″| 25″| 26 1/2″| 13.0 lbs.
RTM5VL28| Battery| 1 1/2″| 120″ x 120″| 28 1/2″| 30″| 23.5 lbs.
2″| 120″ x 120″| 28 1/2″| 30″| 17.5 lbs.
RTMDCZ25| DC| 1 1/4″| 84″ x 84″| 16 1/2″| 18″| 15.5 lbs.
1 1/2″| 84″ x 84″| 16 1/2″| 18″| 13.0 lbs.
RTMDCZ28| DC| 1 1/2″| 120″ x 120″| 22″| 23 1/2″| 23.5 lbs.
2″| 120″ x 120″| 22″| 23 1/2″| 17.5 lbs.

PARTS LIST. See Figure 3

Figure 3. Basic Components

1. Tubular Motor
2. Aluminum Roller
3. Heavy Duty End Pin
4. Wall Brackets
5. Bracket Covers
6. Crown and Drive Set
7. Tube Adapter (as required)

BRACKETS & BRACKET COVERS

BRACKET COVERS:

Available in White /W, Satin Nickel /SN and Black /K. Narrow brackets do not work with covers.

BRACKETS:

Zinc. Work with bracket covers.

Zinc. Don’t work with bracket covers.

MEASUREMENT

Step 1. See Figure 4
Measurement on a window

A. Inside Mount: Measure the Width inside the casing (jam-to-jam, or casing-to-casing), where the brackets will be installed and the Length from the top of the bracke to the bottom of the window. Mark your location.
B. Outside Mount: Measure the Width outside between the outer edges of the window trim where the brackets will be installed; and the Length from the top of the bracket to the bottom of the window. Mark your location.

NOTE: Measure all windows for accuracy even though they may look the same.

Step 2. Cut shade cloth and aluminum roller.

A. Chart for Shade Cloth Width/Roller Tube Length

Tubular Motor Item #| Motor Type| Tube Dia.| Shade Cloth Width/ Roller Tube Length
---|---|---|---
RTM5VL25 RTM5VL25S| Battery| 1 1/4″| Overall Width – 1 5/16″
1 1/2″| Overall Width – 1 5/16″
RTM5VL28| Battery| 1 1/2″| Overall Width – 1 5/16″
2″| Overall Width – 1 5/16″
RTMDCZ25| DC| 1 1/4″| Overall Width – 1 5/16″
1 1/2″| Overall Width – 1 5/16″
RTMDCZ28| DC| 1 1/2″| Overall Width – 1 5/16″
2″| Overall Width – 1 5/16″

Overall width is measured from outside edge of both brackets.

B. Chart for Shade Cloth Length (Finished Shade Cloth Length allows for a bottom bar pocket and to wrap around the roller at the top):

NOTE: Cut the shade cloth square to ensure the shade will travel up and down and not track to the left or right.

INSTALLATION

Step 3. Mount the brackets to the window casing according to the marked locations in Figure 4 (see page 1). Figure 6 shows the proper bracket placement options.  The left and right Skyline brackets are identical so the motor can be mounted on the left or the right side.

Step 4. Slide the crown onto the motor as shown in Figure 8
NOTE: Make sure to line up the notch in the crown and on the motor head.

Step 5. Slide the driver onto the end of the motor shaft. Then snap the drive retainer onto the motor shaft as shown in Figure 9.

Step 6. Insert the heavy duty end pin (and tube adapter where required) and the motor assembly into the roller tube. Make sure  to line up the tabs on the tube with channels on the driver and crown as shown in Figure 10.

Step 7. To install, insert the heavy duty end pin side of the tube into the center hole of the wall bracket shown in Figure 11A. While putting pressure on the spring pin, install the motor end onto the other bracket. The spring pressure will allow the tabs on the motor end to seat into the bracket as shown in Figure 11B.

Figure 11A. End Pin Bracket

Figure 11B. Motor End Bracket

Step 8. Slide the bracket covers onto the brackets as shown in Figure 12.

Figure 12. Bracket Covers

How to get started using your Motorized RollerShade System with a

Battery Motor

• Please read all the instructions provided with your tubular motor.
• Your motor will be shipped in “sleep mode” and must be woken up before using.
• You will need a remote control or a smart phone to set up and control your tubular motor.
• Keep the cords and any loose fabric away from the rotating parts of the roller shade while in use.
• Only use charging options for your motor that are available through Rowley Company.
• Charge the battery motor fully before its first use, which will take approximately 6 hours.
• Battery motors will have an antenna cord out the end of the motor

How to get started using your Motorized Roller Shade System with a DC

Motor

• Please read all the instructions provided with your tubular motor.
• Your motor will be shipped in “sleep mode” and must be woken up before using.
• You will need a remote control or a smart phone to set up and control your tubular motor.
• Keep the cords and any loose fabric away from the rotating parts of the roller shade while in use.
• Only use power options for your motor that are available through Rowley Company.

How to get started using your Motorized Roller Shade System with a

Battery Motor

• Please read all the instructions provided with your tubular motor.
• Your motor will be shipped in “sleep mode” and must be woken up before using.
• You will need a remote control or a smart phone to set up and control your tubular motor.
• Keep the cords and any loose fabric away from the rotating parts of the roller shade while in use.
• Only use charging options for your motor that are available through Rowley Company.
• Charge the battery motor fully before its first use, which will take approximately 6 hours.
• Battery motors will have an antenna cord out the end of the motor.

How to get started using your Motorized Roller Shade System with a DC

Motor

• Please read all the instructions provided with your tubular motor.
• Your motor will be shipped in “sleep mode” and must be woken up before using.
• You will need a remote control or a smart phone to set up and control your tubular motor.
• Keep the cords and any loose fabric away from the rotating parts of the roller shade while in use.
• Only use power options for your motor that areavailable through Rowley Company.
• DC motors will have a power cord and an antenna cord out the end of the motor.

References

• Drapery Workroom & Upholstery Supplies | Rowley
• s7d2.scene7.com/is/content/rowleycompany/rowley-product-instruc-motors-shades-5v-2528mmpdf
• s7d2.scene7.com/is/content/rowleycompany/rowley-product-instruc-motors-shades-5v-35mmpdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>