Shikun Electronics 24728-SKIWB921AU1 Radio Transmitter Instructions

Shikun Electronics 24728-SKIWB921AU1 Radio Transmitter Instructions

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

If power exceeds the limit and the distance（Over 20cm distance in actual use between the device and user） is compliant with the requirement

FCC RF Radiation Exposure Statement:
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden.

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

The device must be professionally installed

The intended use is generally not for the general public.It is generally for industry/commercial use.
The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector.

Installation must be controlled. Installation requires special training

MAX gain: 3.0dBi
Shenzhen KTC, model: 3D0504BK07-001
MAX gain：3.5dBi
Shenzhen KTC, model: SLK-KG-B3DBS-SMA(P) MAX gain：3.5dBi
Shenzhen KTC, model: A100-0062
MAX gain：3.5dBi
Guangzhou Shienthalpy Technology Co., Ltd.，
model: SH-230317-0001
Max gain: 3.08dBi
5100-5900| External Antenna| Shenzhen KTC model: 3D0504BK07-001
MAX gain: 4.5dBi
Shenzhen KTC model: SLK-KG-B3DBS-SMA(P)
MAX gain：5.0dBi
Shenzhen KTC model: SLK-KG-B3DBS-SMA(P)
MAX gain：3.3dBi
Shenzhen KTC model: A100-0062
MAX gain：5.0dBi
Guangzhou Shienthalpy Technology Co., Ltd.， model: SH-230317-0001
Max gain: 4.39dBi

If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AR82-SKIWB921AU1 Or Contains FCC ID: 2AR82-SKIWB921AU1”

When the module is installed inside another device, the user manual of this device must contain below warning statements:

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. This device may not cause harmful interference, and
3. This device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.

The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end user manual shall include all required regulatory information/warning as shown in this manual, include:
This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

Canada Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “ Contains IC: 24728-SKIWB921AU1” any similar wording that expresses the same meaning may be used

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This radio transmitter 24728-SKIWB921AU1 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

The concrete contents to check are the following three points.

1. Should be installed so that the end user cannot modify the antenna;
2. Feed line should be designed in 50ohm

Fine tuning of return loss etc. can be performed using a matching network.

Frequency (MHz)| Antenna Type| Antenna Gain (dBi)
Gain maximal
---|---|---
2400-2500| External Antenna| Zhongshan B&T,
model: AG-011320-0679
MAX gain: 3.0dBiShenzhen KTC,
model: 3D0504BK07-001
MAX gain：3.5dBiShenzhen KTC,
model: SLK-KG-B3DBS- SMA(P)
MAX gain：3.5dBiShenzhen KTC,
model: A100-0062
MAX gain：3.5dBiGuangzhou Shienthalpy Technology Co., Ltd.，
model: SH-230317-0001
Max gain: 3.08dBi
5100-5900| External Antenna| Shenzhen KTC
model: 3D0504BK07-001
MAX gain: 4.5dBiShenzhen KTC
model: SLK-KG-B3DBS- SMA(P)
MAX gain：5.0dBiShenzhen KTC
model: SLK-KG-B3DBS- SMA(P)
MAX gain：3.3dBiShenzhen KTC
model: A100-0062 MAX gain：5.0dBiGuangzhou Shienthalpy Technology Co., Ltd.，
model: SH-230317-0001Max gain: 4.39dBi

Notice to OEM integrator

Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual.
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003.
Host manufacturer isstrongly recommended to confirm compliance with FCC/ISED requirementsfor the transmitter when the module is installed in the host.

Must have on the host device a label showing Contains
FCC ID: 2AR82-SKIWB921AU1，
IC: 24728 SKIWB921AU1

The modular transmitter is only FCC authorized for the specific rule parts (Part 15.247 and Part 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), the final host product still requires Part 15 Subpart B or Part 18 etc. compliance testing with the modular transmitter installed

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>