SJE RHOMBUS CL100 Installer Friendly Series IFS Single Phase Simplex Instruction Manual

: June 12, 2024
: SJE RHOMBUS

Table of Contents

SJE RHOMBUS CL100 Installer Friendly Series IFS Single Phase Simplex
Product Information
TOUCHPAD FEATURES
COMPONENTS
Control and System Monitoring
DESCRIPTION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SJE RHOMBUS CL100 Installer Friendly Series IFS Single Phase Simplex

SJE-RHOMBUS-CL100-Installer-Friendly-Series-IFS-Single-Phase-Simplex-
PRO

Product Information

The Single Phase Simplex is a pump control system that can be used for demand dose or timed dose applications. It is equipped with a Float or C-LevelTM Sensor for pump control, system monitoring, event logging, and reporting. The panel features a touch pad with various indicators and controls for easy operation. The C-LevelTM sensor has different operating ranges depending on the model.

The IFS In-Site® simplex control panel utilizes an innovative circuit board design to control one 120/208/240V single phase pump in water and sewage applications. IFS panels feature an easy-to-use touch pad on inner door for programming and system monitoring. Quick retrieval of all system events can be done by downloading panel information onto a USB flash drive. The panel configuration can be easily converted in the field to either a timed dose or demand dose. Available with the EZconnex® float system.
Monitor system events including pump run times, pump cycles, alarm conditions, power outages, service calls and more! Quick, convenient reports make diagnosing system conditions easy! Plug the flash drive into the USB port located on the inner door of the IFS In-Site® panel to download system events which occurred. No computer is needed at the site! Use the flash drive (included with panel) with any computer to download system information and reports. The pre-loaded software on the flash drive formulates system data for you, creating reports quickly in an easy-to-read format so system conditions can be easily identified and corrected. In addition to monitoring system events, the IFS In-Site® panel logs any service calls and changes made to system settings, which helps protect service providers. The panel can utilize the C-Level™ sensor for continuous level monitoring. It senses the level in the tank and sends a signal to the panel. Pump activation levels can be adjusted by using the panel touch pad. C-Level™ CL40 sensor operating range is 3-39.9 inches (7.6 101.3 cm). C-Level™ CL100 operating range is 3-99.5 inches (7.6-252.7 cm).

TOUCHPAD FEATURES

SJE-RHOMBUS-CL100-Installer-Friendly-Series-IFS-Single-Phase-
Simplex-1

A. Level Status indicators illuminate when floats or set points are activated; alarm will activate if a float operates out of sequence
B. HOA (Hand-Off-Automatic) buttons with indication control pump mode; Hand mode defaults to Automatic when stop level or redundant off level is reached
C. Pump Run indicator illuminates when pump is called to run
D. LED display for system information including: level in inches or centimeters (C-Level™ sensor only), mode, pump elapsed time (hh:mm), events (cycles), alarm counter, float error count, timed dose override counter (timed dose only), pump ON/OFF times (timed dose only), and sequence ON/OFF times (timed dose only)
E. NEXT push button toggles display
F. UP and SET push buttons used to set pump ON/OFF times (timed dose only), date and hour, activation levels (C-Level™ only)

COMPONENTS

SJE-RHOMBUS-CL100-Installer-Friendly-Series-IFS-Single-Phase-
Simplex-2

Enclosure base measures 14 x 12 x 6 inches (35.56 x 30.48 x 15.24 cm); NEMA 4X (ultraviolet stabilized thermoplastic with removable mounting feet for outdoor or indoor use)
Red LED beacon provides 360° visual check of alarm condition
Exterior Alarm Test/Normal/Silence switch allows horn and light to be tested and horn to be silenced in an alarm condition; alarm automatically resets once alarm condition is cleared
Alarm horn provides audio warning of alarm condition (83 to 85 decibel rating) (Not shown)
Circuit breaker (optional) provides pump disconnect and branch circuit protection
Power relay controls pump by switching electrical lines; definite purpose contactor used when pump full load amps are above 15
Float connection terminal block
Incoming control/alarm terminal block
Control Power indicator/fuse indicator light illuminates if control power is present in panel; alarm will activate if control fuse is blown
Alarm Power indicator/fuse indicator light illuminates if alarm power is present in panel
Ground lug
Incoming pump power connections
RF filter
Power supply
Control fuse
Alarm fuse
USB port for flash drive to download time-stamped system events
Manual report switch date and time stamps service calls

Note: Options, voltage, and amp range selected may change enclosure size and component layout.
Note: Schematic/Wiring Diagram and Pump Specification Label are located inside the panel.

Control and System Monitoring

SJE-RHOMBUS-CL100-Installer-Friendly-Series-IFS-Single-Phase-
Simplex-3

CONTROL PANEL| | IFI|
---|---|---|---
MODEL TYPE| | 1| Simplex Timed Dose (includes Option 8AC as standard)
| 2| Simplex Demand Dose (includes Option 8AC as standard)
__**ALARM PACKAGE| | 1| Alarm Package (includes test/normal/silence switch, fuse, red light, & horn)
ENCLOSURE RATING| | W| Weatherproof, NEMA 4X (engineered thermoplastic)
STARTING DEVICE| | 1| 120/208/240V
| 9| 120V only
PUMP FULL LOAD AMPS**| | 0| 0 – 7 FLA
| 1| 7 – 15 FLA
| 2| 15 – 20 FLA

PUMP DISCONNECTS

| | 0| No Pump Disconnect
| 4| Circuit Breaker 120V (select STARTING DEVICE Option 9 above)
Circuit Breaker 120/208/240V (select STARTING DEVICE Option 1 above)

FLOAT SWITCH APPLICATION

| | H| Floats – Pump Down (select Option 17 below)

Timed dose = timer enable and alarm / Demand dose = stop, start, and alarm

| E| EZconnex® Float Switch System

(select Option 33, 35 or 36 below)

PRICING WORKSHEET

IFI Simplex Base Price: __
Alarm Package: __
Enclosure Rating: __
Starting Device: __
Pump Full Load Amps : __
Pump Disconnects: __
Float Switch Application: __
Total Options : __
TOTAL LIST PRICE: __

NOTE: Pump down applications only. Industry practices suggest that a secondary device, such as a float switch, be used for redundant activation of the high-level alarm and pump shut off when using the C-Level™ sensor.

DESCRIPTION

| OPTIONS| DESCRIPTION| | OPTIONS| DESCRIPTION
---|---|---|---|---|---
| 1J| Duo Alarm Inputs| | 17C| Sensor Float® / Internally Weighted (per Float) – Mercury
| 3A| Alarm Flasher| | 17D| Sensor Float® / Externally Weighted (per Float) – Mercury
| 3B| Manual Alarm Reset| | 17G| SJE MilliAmpMaster™ / Pipe Clamp (per Float) – Mechanical
| 3E| High Water Alarm Float (must also select Option 17)

Only Available with Float Switch Application = C

| | 17H| SJE MilliAmpMaster™ / Externally Weighted (per Float) – Mechanical
| 17J| Sensor Float® / Pipe Clamp (per Float) – Mercury
| 4A| Redundant Off

(must also select Option 4D if floats are required)

| Timed Dose| | 18A| Timer Override Float (Timed Dose Float Panel Only)
Demand Dose| | 24E| C-Level™ CL40 Sensor with 4’ Vent Tube and 20’ Cord
| 4D| Redundant Off Float (must also select Option 4A and Option 17)| | 24F| C-Level™ CL40 Sensor with 4’ Vent Tube and 40’ Cord
| 6A| Auxiliary Alarm Contact, Form C| | 24G| C-Level™ CL40 Sensor with 8’ Vent Tube and 20’ Cord
| 8AC| Display Board – Includes: ETM Counter, Events (Cycles) Counter, Alarm Counter, and Override Counter (Timed Dose Only) (in- cluded as standard)| | 24H| C-Level™ CL40 Sensor with 8’ Vent Tube and 40’ Cord
| 24X| No C-Level™ CL40 Sensor
| 29A| C-Level™ CL100 Sensor with 10’ Vent Tube and 20’ Cord
| 10E| Lockable Latch – NEMA 4X| | 29B| C-Level™ CL100 Sensor with 10’ Vent Tube and 40’ Cord
| 10F| Lightning Arrestor (select pump circuit breaker, control and alarm power combined)| | 29X| No C-Level™ CL100 Sensor
| 33D | EZconnex® 3-Port, 25’, with 10’ Floats (3) / Pipe Clamp
| 10K| Anti-condensation Heater (must select if operating temperature is colder than 0 degrees F or -18 degrees C)| | 33E | EZconnex® 3-Port, 50’, with 10’ Floats (3) / Pipe Clamp
| 33G | EZconnex® 3-Port, 25’, with 20’ Floats (3) / Pipe Clamp
| 11C| Additional NEMA 1 Remote Alarm Panel (must also select Option 6A)| | 33H | EZconnex® 3-Port, 50’, with 20’ Floats (3) / Pipe Clamp
| 11D| Additional NEMA 4X Remote Alarm Panel (must also select Option 6A)| | 35D | EZconnex® 4-Port, 25’, with 10’ Floats (4) / Pipe Clamp
| 15A| Control/Alarm Circuit Breaker| | 35E | EZconnex® 4-Port, 50’, with 10’ Floats (4) / Pipe Clamp
| 16A| 10’ Cord in Lieu of 20’ Cord (per Float)| | 35G | EZconnex® 4-Port, 25’, with 20’ Floats (4) / Pipe Clamp
| 16B| 15’ Cord in Lieu of 20’ Cord (per Float)| | 35H | EZconnex® 4-Port, 50’, with 20’ Floats (4) / Pipe Clamp
| 16C| 30’ Cord in Lieu of 20’ Cord (per Float)| | 36D | EZconnex® 3-Port, 25’, with 10’ Floats (2) / Pipe Clamp, Sealing Plug
| 16D| 40’ Cord in Lieu of 20’ Cord (per Float)| | 36E | EZconnex® 3-Port, 50’, with 10’ Floats (2) / Pipe Clamp, Sealing Plug
| | 36G | EZconnex® 3-Port, 25’, with 20’ Floats (2) / Pipe Clamp, Sealing Plug
| 36H | EZconnex® 3-Port, 50’, with 20’ Floats (2) / Pipe Clamp, Sealing Plug