Bally BOXY01 Sport Edge Sensor User Manual
- June 12, 2024
- Bally
Table of Contents
Bally BOXY01 Sport Edge Sensor
Product Information
The Sports Edge Sensor is a portable device designed for sports activities. It complies with the FCC’s radiation exposure limits for an uncontrolled environment. The device must not be co-located or operated in conjunction with any other antenna or transmitter. It is important to avoid direct contact with the antenna or keep contact to a minimum while using the equipment. The device must be professionally installed. The Sports Edge Sensor complies with Part 15 of the FCC Rules, which means it may not cause harmful interference and must accept any interference received. The device is supplied by Bally’s Corporation and is FCC-compliant with a Unique Identifier of BOXY01.
Firmware Update
To perform a firmware update, press the button on the sensor.
Sensor Identification
Each sensor has a unique 8-digit ID that can be read in threeways. Please refer to the user manual for detailed instructions on how to read the ID.
Product Usage Instructions
Switching OFF the sensor
- Push the button on the sensor until the two blue LEDs turn off.
- Hold the button for approximately 5 seconds.
Switching ON the sensor:
- Push the button on the sensor until the Activity LED starts blinking green.
- Hold the button for approximately 2 seconds.
Auto-shutdown:
The sensor will automatically switch off after 2 hours of no motion state and no gateway connectivity.
Hardware Reset:
To perform a hard reset, push and hold the button on the sensor for approximately 16 seconds.
Battery Charging:
To charge the sensor, place it on a Qi standard wireless charger. Ensure that the button and LEDs area is placed outside the charging circle. The POWER LED should start blinking green to indicate charging. The sensor is fully charged when the GREEN POWER LED remains fixed.
POWER LED Status:
- LED OFF: Normal operation
- BLINKING GREEN: Device is charging
- FIXED GREEN: Charging completed
- BLINKING YELLOW: Device is charging + Power Error
- FIXED YELLOW: Charging completed + Power Error
- BLINKING PINK: Power Error
ACTIVITY LED:
- LED OFF: Device is shutdown
- BOTH LEDs BLINKING BLUE: Button is being pressed
- BOTH LEDs FIXED BLUE: Firmware Update
Please refer to the user manual for additional information and instructions on using the Sport Edge Sensor.
Switching OFF the sensor
Push the button till the two blue LEDs switching OFF
Switching ON the sensor
Push the button till the Activity LED start blinking green ****
Auto-shutdown
The sensor is set to automatically switch OFF after 2 hours of no motion state
and no gateway connectivity
Hardware Reset
Push and hold the button to perform a hard reset
Battery Charging
- Place the sensor on a Qi standard wireless charger.
- The button/Leds area should be placed outside the charging circle.
- The POWER Led should start blinking green.
Note : If the Green Power Led doesn’t start, slightly move the sensor on
the charger pad to find the charger coupling location
The sensor is fully charged when the Green POWER Led is fixed
POWER LED
-
LED OFF
Normal operation -
BLINKING GREEN
Device is charging -
FIXED GREEN
Charging completed -
BLINKING YELLOW
Device is charging + Power Error -
FIXED YELLOW
Charging completed + Power Error -
BLINKING PINK
Power Error -
BLINKING RED
Battery LOW – Please charge battery
ACTIVITY LED
-
LED OFF
Device is shutdown -
BLINKING GREEN
IDLE state – Waiting for BLE connection -
BLINKING BLUE
CONNECTED state – Device is connected to the gateway -
BLINKING CYAN
SESSION STARTED state – Device is connected and sending motion data to the gateway
POWER LED + ACTIVITY LED ****
BOTH LEDs BLINKING BLUE Firmware Update
BOTH LEDs FIXED BLUE Button is being pressed
Sensor Identification
Each sensor has a Unique ID to be indentified by the Gateway This Unique ID is a 8-digits ID There are 3 ways to read the ID :
Flash QR-Code with a Smartphone or 2D scanner
Read the text below the QR-Code
FCC statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This portable equipment with it’s antenna complies with FCC’s radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, follow the instructions below:
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment. This device must be professionally installed
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Supplier’s Declaration of Conformity
- Unique Identifier : BOXY01
- FCC-ID : 2A94O-BOXY01
Party issuing Supplier’s Declaration of Conformity
- Bally’s corporation
- 100 Westminster Street
- Providence, Rhode Island
- RI 02903, United States
- Phone : 401.475.8474
Responsible party – U.S. Contact Information
- 100 Westminster Street
- Providence, Rhode Island
- RI 02903, United States
- Phone : 401.475.8474
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>