GlobalSat MR-350N Bulkhead Serial GPS Receiver User Manual
- June 12, 2024
- GlobalSat
Table of Contents
- PACKAGE CONTENTS
- SYSTEM REQUIREMENTS
- GETTING STARTED
- INSTALLING THE USB DRIVER TO YOUR LAPTOP
- COM PORT VERIFICATION
- INITIALIZING YOUR GPS RECEIVER
- USING / TESTING YOUR GPS RECEIVE
- UN-INSTALL THE USB DRIVER
- FAQs
- CONTACT INFORMATION
- SAFETY AND LEGAL NOTICES
- LIMITED WARRENTY
- SPECIFICATION
- Pin Description
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GPS Mouuse User’s Manual for
MR-350N V1.0
RS-232GPS Reeceiver
© 2022 GlobalSat WorldCom Corporation/USGIobalSat, Inc. All rights reserved.
The GlobalSat logo is a trademark of GlobalSat WorldCom Corporation. Windows
is a register trademark of Microsoft Corporation. Acrobat is a registered
trademark of Adobe Systems Incorporated. Mac is a registered trademark of the
Apple Corporation.
All other trademarks or registered trademarks are acknowledged as the
exclusive property of their respective owners. All rights reserved. No part of
this manual may be reproduced, transmitted, copied, or stored in any storage
medium, for any purpose, without prior written consent from GlobalSat WorldCom
Corporation or USGIobalSat, Inc. GlobalSat/USGlobalSat hereby grants the right
to download one (1) copy of this manual onto a hard drive for personal use.
This manual is copyrighted and may contain proprietary information that is
subiect to change without notice
PACKAGE CONTENTS
– GPS Receiver – Simple guide
– lx Nut, 2x Washer, lx Heat Shrink Tube
- Please download the User Manual and driver installation guide at https://www.alobalsat.com.tw/
SYSTEM REQUIREMENTS
The GlobalSat GPS receiver requires a Windows or Macintosh laptop with a USB
port and NMEA compatible navigation software. 3rd party map/navigation
software may have its own system requirements, please consult the software
supplier for details.
WELCOME
Thank you for purchasing the GlobalSat GPS receiver! This product allows you
to use your laptop for real-time street navigation. For Windows OS/Mac OS
simply load the USB driver (MR-350N USB cable set required), plug the GPS
receiver into your computer and install your own personal mapping software,
then you are free to enjoy the real-time GPS services.
GETTING STARTED
There are only a few simple steps that you need to follow before using your
GPS receiver:
■ Download Driver & Gpslnfo utility from Globalsat website support page,
https://www.alobalsat.com.tw/
NOTE: Within your mapping, or navigation software (including the supplied
GPS Information utility), you will need to manually select the correct COM
port which has been assigned to the GPS receiver.
IMPORTANT:
- Set Baud Rate 4800, Data Bit: 8, Parity: None, Stop Bit: 1, Flow Control: None.
- You must check the default Baud rate of your mapping software in order to communicate with the GPS receiver.
INSTALLING THE USB DRIVER TO YOUR LAPTOP
The following steps will show how to install the device under Windows 64-bit OS. The procedures are the same and straight- forward for all other supported Windows operating system versions.
-
Power on your computer and boot to Windows. Run or double-click the PL-2303 Windows DriverInstaller program.
-
The Install Shield Wizard will be displayed to inform you that the PL-2303 USB-to-Serial driver will be installed on your computer. Click Next to continue.
-
The PL-2303 Driver Installer program will then start to install the drivers needed.
-
Click the Finish button to close the Install Shield program. If you have plugged the cable into the PC while running the setup installation, please unplug and replug the cable for the system to detect the device.
COM PORT VERIFICATION
- Once your USB Driver has been installed, you will need to confirm which COM Port your PC has assigned to it in order to properly configure any software that will be utilizing the GPS data being received.
- Your receiver must be plugged into your USB port at this time.
- Using Window’s Control Panel, select System>Hardware>Device Manager
- Then look under the heading of: Ports (Com & LPT)
- There should be a listing for: Prolific PL2303XX USB Serial COM Port (COMx) (“x” will actually be the number your PC has assigned the USB GPS receiver).
- Once you have identified the COM port number, any software that you utilize must be configured to read GPS data from this COM port.
We strongly recommend that you first download the “Gpslnfo” utility from the
Globalsat official website to test your USB GPS to confirm whether the GPS
receiver is working properly on your PC and whether you have successfully
configured the correct COM port settings. After completing this operation,
close the GPS information program and start the COM port configuration
application.
NOTE: By default, your PC will not allow you to run multiple applications
from a single COM port. It is important that you close any previously opened
GPS application before switching to another GPS application as the GPS
receiver and data will not be found by the new program.
INITIALIZING YOUR GPS RECEIVER
Before using your GPS receiver for navigation (especially for the first time),
the receiver must obtain a local GPS fix (coordinates) of the current
position. To do this take your laptop (with your USB driver and the mapping
software loaded and configured) to an open area that has a clear view to the
sky (such as a park or empty field). Start your software (or the included
“GPSInfo” utility program) and wait for initialization of the GPS to complete.
This may take a few minutes depending on various factors such as the distance
of the current coordinates from the last time the GPS receiver was activated,
GPS signal strength and surrounding terrain (tall trees and buildings can
block the satellite signals). Once the RAW GPS data is displayed onto the
screen, if applicable for your software, a fix has been initialized . In some
cases, initialization can take up to several minutes depending on the
conditions mentioned above before complete GPS data will be displayed on the
screen.
Coordinates scrolling with zero’s means that the port connection is complete,
but the satellite data is not being received yet (possibly still initializing
or in a bad area for satellite reception).
USING / TESTING YOUR GPS RECEIVE
Once the GPS receiver’s driver and your personal mapping software have been
installed and configured properly, you can begin to use your navigation system
by plugging the receiver into your laptop. If you don’t have a mapping, or
navigation software, we’ve included a GPS test utility called “GPSinfo” for
the purpose of confirming your installation and configuration. This utility
can be installed by executing “GPSinfo.exe” file in Windows and can be
downloaded from our website https://www.alobalsat.com.tw/ .
• Recommended installation location of the receiver:
Always select an area in the vehicle where the GPS unit will be secure and not
obstruct normal driving, visibility and safety, but still maintaining a “view
to the sky” in order to receive satellite data.
• GPS information function test setting:
- Run Gpslnfo.exe to load the utility.
- Enter the proper COM port for your GPS device (see COM Port Verification above)
- Set COM port to Baud rate: 4800
- If no errors have been made in configuration, there should be GPS data being displayed in the window, which is the confirmation that the communication between the GPS device and the “GPSinfo” software is working properly.
- If there is no GPS data displayed (or data with multiple zeros in them), please exit the software and unplug the GPS receiver from USB port and reinsert it after 10 seconds to reset the device.
NOTE: The correct COM port configuration between the GPS Device and your mapping software must be completed before using the software for the first time.
• Gpslnfo user interface description:
- COM Port: Corn port selection.
- Baud Rate : Choose a preset Baud Rate.
- Core Ver: Show Core version location.
- FW Ver: Show FW version location.
- Send : Execute input PAIR command.
- Log File: After entering the file name, check to start NMEA data LOG.
- Start GPS : Start/Stop GPS Date.
- Get Version: Show Core & FW version.
- Cold Start: Not using the Position, Almanac and Ephemeris data at the start.
- Change Baudrate: Confirm to replace the selected Baud rate.
- 4800-921600 : Select the Baud Rate to switch.
- NMEA message output
- Satellite signal display: Position and accuracy and number and signal strength.
UN-INSTALL THE USB DRIVER
Run the file the PL-2303 Driver Installer.exe to uninstall the USB GPS driver.
FAQs
I am not getting GPS data into my application.
- Check your DEVICE MANAGER to confirm the COM Port number assigned to the GPS Receiver (it will be listed under the PORTS (COM & LPT) heading as Prolific Serial-to-USB Comm. Then be sure this is the same COM port number configured in your application.
- Be sure your Baud rate is configured correctly at: Baud Rate: 4800 Data bit: 8 Parity: None Stop Bit: 1 Flow Control: None
- Re-boot your computer and then insert the USB GPS into a USB port.
- Configure the GPS Info utility with the correct COM Port and test your GPS receiver first before using it in your application.
Will the GPS work with other Street Mapping software?
GlobalSat GPS receivers provides standard NMEA data for mapping software to
use and convert to coordinates and should work well with mostly any NMEA
compliant software on the market today.
How accurate is the GPS?
The USB GPS is WAAS/EGNOS capable, and for units sold in North America through
authorized resellers, these units are WAAS/EGNOS enabled unless otherwise
stated. Accuracy can be up to 5 meters 3D RMS with WAAS enabled and 10-15
meters 2D RMS WAAS disabled.
Why do I only see the GPS signal?
Due to huge amount of NMEA data for all satellite systems, the default Baud
rate 4800 will only support NMEA from GPS and hide others.
What is ideal GPS environment?
The GPS requires an open, clear view of the sky. Buildings, covered parking
areas, tunnels and dense foliage can cause the GPS receiver to be unable to
get a location fix.
If you are parked in a covered parking lot or near a tall building, it is
recommended that you drive away until you have a clear view of the sky before
using. You may need to give the GPS a few minutes to find or get a fix its
location.
How do | know if the GPS is ON?
Your USB GPS must be plugged into your laptop’s USB port to get power. If your
PC is on and the COM port was configured properly, the GPS receiver is on and
receiving the streaming GPS data. This can be verified by opening your mapping
software program.
Why does the GPS not work near buildings and other tall objects?
The GPS uses satellites in the space to find out where it is. Therefore it
needs a clear view of the sky. Tall buildings and other objects that block the
receiver’s view to the sky make it infeasible to determine your location.
Sometimes the satellites are not overhead but near the horizon. In these cases
the GPS must have a clear view of the horizon.
Other Comments-
Please allow an adequate amount of time for the GPS receiver’s boot-up (TTF)
to complete before contacting Technical Support.
You can download the latestDriver Installer program from Prolific Support
website:
http://www.prolific.com.tw/US/CustomerLogin.aspx
CONTACT INFORMATION
GlobalSat WorldCom Corporation (Taiwan),
www.globalsat.com.tw
service@globalsat.com.tw (pre-sales GPS
product questions only)
USGlobalSat, Inc.
sales@globalsat.com (pre-sales GPS product
questions only)
For technical support, please refer to our website to learn about GPS
solutions and driver data updates. https://www.globalsat.com.tw/Support
Pre-registration is required before receiving any type of technical support.
Support issues submitted via phone, fax or e-mail (any means outside of the
recognized “Trouble Ticket” generated from your own USGlobalSat registered
account) WILL NOT be answered. Create your account and register your products
at:
https://www.globalsat.com.tw/Contact
SAFETY AND LEGAL NOTICES
Please read this section carefully before using the GPS receiver
GlobalSat WorldCom Corporation / USGlobalSat, Inc. will not accept any
responsibility whatsoever for accidents resulting from failure to observe
common sense precautions. Your personal judgment, traffic regulations, and
common sense must always take precedence over any directions produced by GPS
receiver or the mapping software
WARNING: Make sure the GPS receiver is secure and does not interfere with
driving visibility and safety.
It is your responsibility as the vehicle operator to securely place the GPS
unit and antenna so that they will not interfere with driving and prevent
operations of any safety device (such as the Airbag) in your vehicle. Do not
mount the devices in a place where the driver or passengers may receive injury
during vehicle operation or collision. For your safety, take care to route all
cables away from shifters, pedals, accessory controls and mechanisms.
WARNING: Drive safely and use common sense.
It is your responsibility as the vehicle operator to drive safely, observe all
traffic rules and above all use your own personal judgment while driving. If
you feel that a route suggested by the navigation software instructs you to
perform an unsafe or illegal maneuver, places you in an unsafe situation, or
routes you into an area which you consider unsafe, do not follow the
instructions.
WARNING: Keep your eyes on the road.
It is your responsibility as the vehicle operator to keep your eyes on the
road and be an alert driver at all times, especially when the vehicle is
moving. The vehicle’s operator should not be distracted by the navigation
equipment or software. Should there be a distraction with the ability to drive
responsibly, please tum off the device. Should you want to look at the display
for a prolonged time, park the car safely, while following all traffic
regulations before looking at the display.
WARNING: To reduce the risk of fire or shock hazard, do not expose this
product to rain or moisture. Do not remove covers or open housings, there are
no user serviceable parts inside. Refer servicing to qualified personnel only.
LIMITED WARRENTY
GlobalSat/USGlobaiSat warrants product hardware against manufacturing defects
in material and workmanship under normal use for a period of one (1) year from
the original date of purchase (unless the product states otherwise), and only
when Purchased from a recognized “authorized dealer”. Products purchased from
any unauthorized source, such as unauthorized e-Bay resellers, will not
qualify for free warranty service/support and may require the end-user to pre-
pay fees associated with, but not limited to the support, repair, replacement
and shipping of the product to and from the service center.
Except as provided herein, GlobalSat/USGlobalSat makes no express warranties,
including but not limited to any warranties of merchantability or fitness for
particutar use, or non-infringement. You acknowledge that your use of the
product or service is at your sole risk and you agree that the information
provided are without warranty of any kind by GlobalSat/USGiobalSat.
Under no circumstances, including negligence, will GlobalSat/USGlobalSat or
any of its affiliates, directors, officers or employees, or any third party be
liable for any direct, indirect, incidental, special or consequential damages
that results from your use, or your inability to use, of the performance of
the product(s) with respect to any liability, loss, or arising out of any
breach of this warranty, including, but not limited to any damages resulting
from inconvenience, loss of time, data, property, revenue, or profit or any
indirect, special incidental or consequential damages. You acknowledge that
this limitation applies to all content information or other services available
from GlobaiSat/USGiabalSat, and whether or not GlobalSat/USGlobaiSat has
notice of the possibility of such damages, and whether or not to circumstances
giving rise to such damages may have been within the control of
GlobaiSat/USGiobalSat.
Some states do not allow the exclusion of certain warranties, so some of the
above exclusions may not apply to you. In those states, liability is limited
to the fullest extent allowed by law by using the product(s), you agree to
indemnify Globalsa/USGlobaisat and its parents. subsidiaries, affiliates,
officers and employees and hold them harmless from any and all claims and
expenses, including reasonabie attorney’s fees, asserted third party due to,
or arising out of your use of the service and the site.
In the event of a product defect during the first 30-days of the warranty
period, return product and the saies receipt as proof of purchase date to
place of original purchase. Defect discovered after 30-days from date of
purchase, you must contact GlobaiSat/USGiobalSat’s Technical support for a
Return Merchandise Authorization (RMA) number for return to manufacturer.
GlobalSat/USGlobaiSat will, at its option, unless otherwise provided by law:
a.) Correct the defect by praduct repair without charge for parts and labor.
b.) Replace the product with one of the same or similar design; or Refund the
purchase price. All replaced parts and products, and products on which a
refund is made, become the property of GlobaiSat/USGiobalSat. New or
reconditioned parts may be used in the performance of warranty service.
Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the
product made after the expiration of the warranty period.
This warranty does not cover:
a.)Damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow the
instructions, improper installation or maintenance, alteration, lighting or
other incidence of excess voltage or current;
b.)Any repairs other than those provided by Globalsat/USGlobalsat;
c.)Consumables such as fuses or batteries;
d.)Cosmetic damage;
e.) Transportation, shipping or insurance costs;
f.)Costs of product removal, installation, set-up service adjustment or
reinstallation.
This warranty gives you specific legal rights, and you may also have other
rights, which may vary from state to state.
Additional products bundled in this package not manufactured by
Globalsat/USGlobalsat will hold separate warranties as expressed by the
individual manufacturer of that product(s). Product specifications, functions
and features are subject to change without notice.
SPECIFICATION
Due to continuous product improvements, all specifications are subject to change without notice.
Pin Description
(MD-6) Malc-type
Pin1:Ground(Black)
Pin2:VCC(Red)
Pin3:1PPSCYellow)
Pin4:RX(White)
Pin5:TX(Green)
Pin6:NC
PIN Number(s) | Name | Type | Description |
---|---|---|---|
1 | GND | Power | Ground. |
2 | VCC | Power | This pin is the main DC supply for a 4.5V -6.5 DC input power. |
3 | 1 PPS | Output | This pin output signal based on firmware setting.* |
4 | RX | In put | This pin is the main receive channel for receiving software |
commands to the GPS receiver from “Gpslnfo” software or from user written
software.
5| TX| Out put| This is the main transmit channel for outputting navigation
and measurement data to user’s navigation software or user written software.
6| NC| NC| Just NC.
- 1PPS firmware preset output: No Fix =Low / 3D Fix= Hi lms , Low=999ms (Hi level=1.8V).
References
- alsat.com - This website is for sale! - alsat Resources and Information.
- at.com.tw
- Maquinaria y Productos para Hostelería | Balsat
- www.gl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>