HDT H5 Handheld Gimbal User Guide

HDT H5 Handheld Gimbal

Product Specification

• Model No:H5
• Material:ABS+AL
• Playload:300g
• Net Weight:230g
• Battery Capacity:Li-ion 450mAh
• Charging Port:Micro USB Charging Voltage:5V
• Working Current:100mA~2100mA
• Operation Time:2H
• Charging Time:1H
• RCU Control Distance:Within 10m RCU
• Battery:Lithum Cell CR1632 RCU
• Modulation Type:GFSK
• Product Size:1907040mm
• Extension Length:580 mm

Overview

1.  Micro USB Port
2.  Gimbal LED Indicator
3.  Power Key
4.  Positioning Bead
5.  Rotation Lock
6.  Pull Rod
7.  Controller Indicator
8.  Controller Switch
9.  Tripod

Charging for Gimbal
Charge the gimbal with the Micro USB cable and USB adaptor, When charging,the red LED turns on and the indicator will be off after the charging is finished

**Change Battery for Controller

**

Power Off Machine
Controller Powe Off:Press the switch key for 3 seconds and the blue light flashes out,indicates shutdown. Gimbal Power Off:Press power key for 5 seconds, the green LED goes out,indicates shutdown。

User Guide

1.  Press the controller switch for 3 seconds to power on the RcU,the green LED turns on,
2.  Turn on Bluetooth on mobile phone,search and connect to Bluetooth device named”H5″,open camera App on phone after bluetooth connectioAn is succeed,click shutter key to take photos and videos.
3. Open the phone clip and place smart phone in holder,move and adjust the holding position until phone is fixed in balance level. If the gimbal is not well-balanced and turn it on in this state,it would be over heat or cause excessive power consumption.
4. Turn On Gimbal Function Rotate the gimbal unit clockwise to make it out of control by positioning bead,press the power key for 5 seconds to turn on gimbal function.

Take photos or videos under gimbal mode

Click power button of gimbal,gimbal will rotate 90 degree clockwise then switch automatically between vertical screen mode and landscape mode.

When the gimbal function shuts down or battery uses off,turn around the body until it is locked with the positioning bead, it can be used as a traditional setfie stick.

Tripod Function
Open the tripod,place it on a horizontal table and adjust the overal center of gravity and avoid tilting.

Reminder

1.  If the gimbal is not well-balanced before turn on,it would be over heat or cause excessive power consumption.
2.  Bluetooth RCU goes into sleep mode automatically if there is no any operation within 10 minutes,and click the power key to wake it up.
3.  When the battery of gimbal is low,the red LED is flash,please charge the gimbal.
4.  when the battery of RCU is low,the red LED turns on,please change the cell battery of CR1632.
5. If the machine has been undergone drastic temperature or humidity changes and the gimbal is not being in balance level after power on,the gimbal should be calibrated again as below: Turn off gimbal and remove the gimbal unit out of stick,then put it on a flat table,power it on,click the power key 5 times in succession,the gimbal shall make 3 short beeps plus 1 long beep,then boot up again,gimbal function recover to the nomal status successfully.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help
  This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

Warranty Card

Dear customer,
Thanks for purchase of our professional products! We warrants that your purchase is free from defects in materials and workmanship under normal use during the limited waranty period.The warranty begins on the original date of purchase on your sales receipt.If service is required,a copy of the sales receipt must be included with an explanation of the problem.The followings cases are not included under the warranty:

1.  Unable to provide legitimate receipt and warranty card with correct informaiton.
2.  The damage caused by human or irresistible factor.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>