H Koenig V34 Iron Steam Station Ceramic Soleplate 6 Bar Instruction Manual
- June 6, 2024
- H Koenig
Table of Contents
Instructions Manual
v34
Steam station iron
https://goo.gl/nmQR1V
STEAM STATION IRON INSTRUCTION
DESCRIPTION
- Heating plate
- Steam jet button
- Thermostat knob
- “Iron heating”indicator light
- Single hose (supply cable + steam hose)
- On/off boiler switch
- Steam indicator light
- On/off master switch| 9) Supply cable with plug
- The cleaning valve of the boiler
- Take-up groove
- Boiler
- Resin box
- Water tank
- Water – adding entry lid
---|---
Read this instruction booklet carefully before installing and using the machine. In this way you will obtain the best possible results and maximum operating safety.
SAFETY WARNINGS
Read the following instructions carefully:
-
Before use, check that the power supply corresponds to the voltage shown on the serial number plate. Connect the appliance only to a properly earthed power outlet (minimum 10A).
-
n the event of incompatibility between the plug and you socket, have the socket replaced by a qualified electrician.
-
The electrical safety of this appliance is only guaranteed when it is properly earthed according to current electrical safety regulations. The manufacturer declines all responsibility for any damage resulting from inadequate earthing of the appliance. If in doubt, consult a qualified
electrician. -
Do not leave water in the machine when the room temperature is 0 or below.
-
After unpacking, check the appliance for damage if in doubt, do not use the appliance; contact a qualified technician.
-
Packaging materials (plastic bags, polystyrene foam, etc.) are a potential source of danger and must be kept out of reach of children.
It is inadvisable to use adapters, multiple sockets and/or extensions. In cases in which this is unavoidable, always use adapters, multiple sockets and extensions which comply with current safety regulations. Do not exceed the maximum power rating shown on the adapter.
- This appliance is designed for domestic use only. Any other use of the appliance is considered improper and therefore dangerous.
- The manufacturer declines all responsibility for any damage resulting from improper, incorrect or careless use of the appliance.
- This appliance is not intended for use by persons (include children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- When using any electrical appliance, a few basic rules should be observed:
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- Don’t allow children in the front of the iron when press “Jet button”, its `s shot range is far.
In particular:
- Do not touch the appliance with wet or damp hands or feet.
- Do not use the appliance in bathrooms.
- Do not pull the supply cable or the appliance to remove the plug form the socket.
- Do not leave the appliance exposed to atmospheric agents (rain, sun, frost, etc.).
- Do not allow the appliance to be used by children or irresponsible persons unless under supervision.
- Do not immerse the appliance in water.
- Do not leave the iron unattended when it is switched on, as this may be a source of danger.
- Before carrying out any cleaning or maintenance operations or filling water into container, always disconnect the appliance from the mains power supply by removing the plug.
- In the event of failure or malfunction, switch off the appliance and do not attempt to carry out repairs. Contact an authorized Service Centre and insist on original spare parts. Failure to observe the above points may affect the safety of the appliance.
- Should you decide not to use the appliance again, remove the plug from the socket and cut the supply cable to render the appliance completely inoperative.
- Installation must be carried out according to the manufacture’s instructions.
- The supply cable must not be replaced by the user, as this requires the use of special tools, if the supply cable is damaged, contact an authorized Service Centre.
- Do not allow the supply cable to come into contact with the ironing plate.
- If the safety cut-out intervenes, the iron will no longer function. To restore normal operation. Contac a qualified electrician.
- Never direct the steam jet in the direction of persons, as this may be extremely dangerous.
- Do not use the iron on very wet fabrics.
- Do not place the iron to the person on the stand when the plate is hot.
- Do not overfill the water tank and do not add stainremovers of similar products to the water tank or the boiler..
- Remove the plug from the mains socket when the appliance is not in use. Do not leave the appliance switched on unnecessarily.
- Never unscrew the cleaning valve when the appliance is connected to the power supply network.
- The appliance must be placed on a flat surface that is particularly resistant to high temperatures.
- EEC Directive 87/308(D.M. 13/04/89)Keep this booklet in safe place for future reference. This appliance complies with EEC Directive 87/308(D.M. 13/04/89) regarding the suppression of radio disturbance
PREPARATION FOR USE
The appliance uses ordinary tap water. If the water is very hard (hardness
higher than27 degrees French).we suggest using distilled or demineralized
water. Before using equipment, open the flap of water (15), added just the
right amount of water to the water tank (14), first is less than the MAX water
level. Connecting the appliance and power cord. Press the main switch (8),
power indicator light (8) lights up, it means the iron start running. In the
condition of the equipment only dry hot function.
At the same time, press the boiler switch (6), the boiler power light (6) and
steam available indicator light (7) light up, it means the boiler (12) start
running. The appliance is the steam mode. Feed-water from electromagnetism
water pump coming down the boiler when the boiler(12) heating enough. Choosing
the temperature by temperature knob(3),the colored part indicate ironing area
which can be chose. Around 90 seconds . Heating indicator(4) will die out , it
means the appliance can be using the steam.
Around 3 minutes. Steam available light (7) will die out, it means the
appliance can be using the steam.
If you exit out the steam mode, you just press again the boiler switch
button(6), the boiler power indicator light (6) goes out, it means the
appliance exits out the steam mode.
Cheak the manufacturer’s label on the garment, and interpret the symbol on the
label as follows.
**STEAM IRONING
**
When using the iron for the first time, iron a plain cloth first. Obtain steam
after pressing the steam button (2). This appliance is also able to generate
steam in a vertical position and can therefore be used to refresh fabrics
easily with a jet of steam. If you hear the loud feed-water sound when you
ironing, it means there is no water in the water tank(14).Press the boiler
button(6) and cut down the boiler power . After fill the water tank(14),then
press the boiler button(6) again ,go on ironing.
CAUTION! Never attempt to open the cleaning valve(10) while the boiler is
under pressure.
DRY IRONING
Connect the appliance to the mains supply, only press the main switch(8), then select the desired temperature by turning the thermostat knob(3).Wait until the iron heating indicator light (4) goes off, indicating that the desired temperature has been reached.
PUTTING THE APPLIANCE AWAR
- After use, always allow the iron to cool before putting it away.
- It is not necessary to drain the boiler after ironing.
- Position the Steam flexible hose- Power cable get together in the base of the appliance10.
- Always keep the surface the ironing plate perfectly clean. To clean it, just wipe the cold surface with a damp cloth. The appliance must not be cleaned with descaling agents.
- o not iron over zippers, hooks, rings, etc; as these may scratch the plate.
- When you have finished ironing. Place the iron correctly on its stand. Ensure that there are no traces of water under the plate, as these may cause stains. – Store the appliance in a dry place
CLEAN THE BOILER AT REGULAR INTERVALS
Release the residual steam in the boiler when you use up. Cut down the power, after the appliance refrigeration enough put up one side of the cleaning valve(10), turn the cleaning valve(10)(do not lie flat the appliance when you open the cleaning valve, otherwise the water will leakage).Then fill appropriate water into boiler, insert the boiler cleaning brush and turn the cleaning brush to clean the boiler, then waggle the equipment softly and pour- out the water. Repetition clean 2-3 times, then assemble the cleaning valve back and screw it tightly.
SUGGESTIONS
- Divide the washing according to the correct ironing temperatures. Start by ironing those garments that require a lower temperature. For fuller details, refer to the chart at end of this booklet.
- Fabrics such as velvet and wool, and accessories such as gloves, handbags, etc. will regain their brand-new look and texture by simply passing the iron near the surface of the fabric and pressing the steam button.
- Imprints left in carpets by furniture can be removed by applying steam on the parts where the pile is crushed and the brushing lightly.
If the carpet is made of synthetic material, do not select a high temperature.
How to get a professional ironing finish
A normal iron generates only a small quantity of steam. In this case it is
necessary to products steam constantly in order to eliminate crease in the
fabric being ironed. A professional ironing system works rather differently.
The fabric is first made damp by the steam and then, in a second phase, dry-
ironed in the normal way. This means that every. Tiniest crease is removed and
your garments are ironed to perfection.
In the first phase (steam-damping of the fabric),hold the iron about 20 cm
above the fabric and press the steam(2). Pass the iron over the garment in a
circular movement so that the powerful jet of steam damps the fabric. Lightly
creased garments require only a few moments of steaming. While very heavy
fabrics or garments with particularly difficult creases must be damper, so
steam must be applied for a few seconds more.
During the second phase (dry ironing), check that the thermostat knob is in
the correct position for the type of fabrics; release the steam button(2) and
dry-iron the garment. The special ironing plate will prevent the fabrics from
becoming shiny. Using this ironing technique, and following the suggestions in
the chart below, you will find it easy to give your garments a really
professional ironing finish.
Guide to perfect ironing
Type of fabric| Position of thermostat
knob| Ironing instructions
Acetate Acrylic Nylon| •| Dry ironing
Follow the instructions on the label of the garment. This type of fabric
generally requires very light ironing.
Pollester Rayon| •| Dry ironing
Iron inside out. When ironing mixed fabrics. Select the Lowest recommended
temperature.
Silk| •
•| Dry ironing
Iron inside out.
Wool
Light
cotton
Light linen| •
•| Steam ironing
Iron inside out. Place a thin cloth over the fabric in order to avoid a shiny
finish
CottonFine linenStarchedfabrics| •
•
•| Steam ironing
Dampen the fabric before ironing. Heavier fabrics and tarched fabrics can be
ironed on the front; darker colours and embroidered garments should be ironed
inside out.
Linen| •
•
•| Steam ironing
Use plenty of steam and iron dark fabrics inside out in order to avoid a shiny
finish, Iron lapels and cuffs on the right side for better finish.
ENVIRONMENT
CAUTION:
Do not dispose of this product as it has with other household products. There
is a separation of this waste product into communities, you will need to
inform your local authorities about the places where you can return this
product. In fact, electrical and electronic products contain hazardous
substances that have harmful effects on the environment or human health and
should be recycled. The symbol here indicates that electrical and electronic
equipment should be chosen carefully, a wheeled waste container is marked with
a cross.
Adeva SAS / H.Koenig Europe – 8 rue Marc Seguin – 77290 Mitry Mory – France
www.hkoenig.com –
sav@hkoenig.com –
contact@hkoenig.com – Tél: +33 1 64 67 00 05
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>