Dryflow IFSM092A-ANON Series Bi-Tap Wash and Dry Instruction Manual

IFSM092A-ANON / IFSM093A-ANON
INSTALLATION AND OPERATING
MANUAL
The trusted independent experts for hand dryers and washrooms since 2012. sales@ihdryers.co.uk | 0114 3540047
7 Riverside Court, Don Road, Sheffield S9 2TJ

SAFETY INSTRUCTIONS

Before to carry on any operation, please read carefully and take into account the following safety instructions:

• Only a qualified technician can install, adjust and maintain this device. All these operations must be always done according to the current legal European Standards of installation and according the local installation regulations as well.
• Be careful when the casing of the appliance is dismantled because active parts of the device become accessible and then there is a potential risk of an electric shock.
• Before any electrical manipulation, the electrical current must be cut in order to avoid any electric shock risk
• Means for disconnection, with contact separations at least 3 mm (0.12″), must be incorporated in the fixing wiring involving all poles, accordingly to the current legal European Standards.
• The installer must make sure that the electric system is grounded in accordance with the law in force.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The device could not be installed on a normally inflammable surface.
• To fix the hand dryer to the wall follow the instructions of this manual and use the template provided with the device as well. To fix the machine with adhesives or similar methods is forbidden by the European safety standards.

BOX CONTENT

1 – Motor Unit
2 – Air Unit
3 – Screw bag

PRIOR TO INSTALLATION

LOCATION
The Wash & Dry hand dryers from Dryflow are supplied with 1300mm hose on the IFSM092A-ANON and 1300mm hose on the IFSM093A-ANON, then the ‘motor unit’ must be placed within the hose length to the ‘air unit’.
BASIN/DECK
The used basin or deck shall admit a hand dryer installation according to the present installation manual.
The baisn/deck must have a minimum depth of 120mm, vertical walls and not so rounded edges in order to avoid splashes.
SPACING
On the IFSM092A-ANON the spacing to the water faucet must be at least 140mm.
On the IFSM093A-ANON the spacing to the water faucet must be at least 150mm and has to be installed at least 120mm above the bottom of the basin.

INSTALLATION

‘AIR UNIT’ INSTALLATION M092A
Drill a 33-35mm hole on the basin/deck if it is not already drilled.
A – Place the ‘air unit’ in the hole, inserting the IR sensor wire in advance.
B – Firmly hold the ‘air unit’ to ensure a correct placement, insert the rubber gasket, the earth tag and tighten the fixing nut.

‘AIR UNIT’ INSTALLATION M092A
Drill a 50mm hole on the wall.
A – Place the ‘air unit’ in the hole, inserting the IR sensor wire in advance.
C – Firmly hold the ‘air unit’ to ensure a correct placement, insert the washer, the earth tag and firmly screw the 3 M6 nuts.
C – Move the bezel to completely hide the hole

‘MOTOR UNIT’ INSTALLATION
Carefully remove the casing since it is connected to the base by a tab that joins the two pieces (casing and base) at the rear. Remove the casing keeping it at an angle at all times (Figure 3) until the upper tab is completely withdrawn, taking care to not damage the internal components, in particular the electronic circuit, and not damage the surface of the casing.
ATTENTION:
WHEN THE CASING IS DISMANTLED ACTIVE PARTS OF THE DEVICE BECOME ACCESSIBLE.
A – Make four drill holes with an 8 mm (0,31”) diameter in the wall, using the provided template.
B – Pass the electrical cables from the power grid through the hole with the 22 mm (0,87”) diameter which is situated above the device’s terminal strip.
C – Firmly screw the base of the device to the wall, ensuring that the 4 silent- blocks are correctly placed between the base and the wall
D – Connect the electrical cables to the hand dryer’s terminal strip. Connect the cables corresponding to the two phases (N and L) and to earth in the corresponding sockets of the terminal strip, as indicated by the engraved letters. When making these connections contemplate means for disconnecting from the power grid with a minimum contact separation of at least 3 mm (0,12”) for all poles. These disconnection means must be incorporated into the fixed installation. The hand dryer must be installed against a solid surface only (wall, partition, or similar).       AIR HOSE CONNECT M092A
A – Place the wire through the adaptor tube cut, placing the gasket in the tube hole.
B – Place the clamp in the adaptor tube and connect it to the ‘air unit’. Place the adaptor tube as high as possible not forcing the wire. Firmly tight the clamp.
C – Connect the earth terminal. AIR HOSE CONNECT M093A
A – Place the clamp in the adaptor tube and connect it to the ‘air unit’. Firmly tight the clamp.
B – Connect the earth terminal. IR SENSOR WIRE CONNECTION AND CASING CLOSE
A – Connect the sensor IR wire to the electronic board.
B – Route the wire inside the plastic protector and place it in the casing.
C – Carefully place the casing on the base of the device. To do so place it over the base with a slight incline from top to bottom, in such a way that the tab in the casing correctly inserts into the corresponding slot in the base. D – Place the washer, the earth wire and the screws for fixing the casing to the base, fixing them tightly using the special spanner provided. Confirm the earth terminal is firmly installed, not loose or detachable.

ADJUSTMENTS

ADJUST THE SPEED OF THE MOTOR AND THE DETECTION DISTANCE
The hand dryer has means to adjust manually the distance for detecting hands and the speed of the drying air.
These adjustments of the motor speed and detection distance must be made by a qualified technician only.
The adjustments can be made by moving the respective cursors of the two linear potentiometers, as shown in figure. HEATING ELEMENT
Some models of the hand dryer incorporate an internal heater that may be enabled by a switch.

HOW TO USE

The hand dryer starts automatically when the hands are placed near the LEDs detection zone, which is just next to the air outlet. Hand detection and the ensuring starting of the machine is based on emission-reflection-reception of an IR light beam coming from the sensors. The detection distance is between 120 and 150 mm approximately. (4.72 – 5.9”).

PREVENTIVE MAINTENANCE AND CLEANING

Adequate cleaning of the hand dryer will extend its useful life. It is recommended to remove any dust accumulated inside the hand dryer at least once a year.
To clean the hand dryer correctly, take the following steps:
Disconnect the hand dryer from the power supply.
Clean away the dust and remove any dirt accumulated inside the hand dryer, using a dry cloth or a soft brush.
Clean from the air input to inside the motor (upper part of the nozzle) preventing dust or dirt falling inside the turbine-motor assembly.
Carefully clean the dust away from around the electronic circuit located inside its box- type housing. Carry out this operation taking maximum care not to damage any component of the electronic circuit.
Clean the casing using a damp cloth moistened in a solution of neutral soap and water. After cleaning the entire surface rinse the soap from the casing using another cloth moistened in water and dry using a dry cloth.
Close the hand dryer by assembling the casing once more, tightening the screws that fix the casing to the base and connect to the power grid.
Start the hand dryer up 2 or 3 times in a row to ensure that all remaining dust is extracted.
REPLACEMENT OF INLET AIR FILTER
Replace the old filter by pulling from the lateral flaps.

CONNECTION DIAGRAM

BASIC EXPLODED VIEW

TECHNICAL SPECIFICATIONS

MODEL| MO9A/
MO9AB| MO9AC| MO9ACS
---|---|---|---
GENERAL:
Power supply:| 220 — 240 V
Power consumption:| 3,4 — 6.4 A
Nominal rating:| Motor (min)
Heater OFF| 3.4 Amp| 420 W
Motor (min) Heater ON| 3.8 Amp| 530 W
Motor (max)
Heater OFF| 4.8 Amp| 1100 W
Motor (max) Heater ON| 6.4 Amp| 1600 W
Weight:| 4 7 Kg. (10,4 lb)
IP:| IP 23
Type of insulation:| Class I
MOTOR:|
Rating:| 420 — 1.100 W (0,60 — 1,5 Hp)
Type:| Universal brush motor
Speed:| 19.000 — 30.000 rpm
HEATING ELEMENT| 400 W
TURBINE:| High pressure centrifuge
|
SIZE:|
Height:| 330 mm (13″)
Width:| 213 mm (8,4″)
Depth:| 170 mm (6,7″)
CASING:|
Material:|  Steel| AISI 304 Stainless steel
Thickness:| 1,5 m. (0,06″)
Finish:| White paint| Polished| Satin
APPROVALS:| CE, GS, EMC, G-Mark
AIR OUTPUT:|
Air flow:| 58 — 87 rNs (13.585 — 20.345 LFM)
Air speed:| 2.093 — 3.156 l/min (87 — 131 CFM)

DISPOSAL OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT BY DOMESTIC USERS IN THE EUROPEAN UNION.
The product you have purchased has been designed and manufactured using high- quality materials and components that can be recycled and reused.
If you see a product marked with this symbol, consisting of a crossed-out rubbish bin with wheels, it means that the product is regulated by European Directive 2002/96/EC regarding the disposal of waste electrical and electronic equipment. This symbol indicates that the product must not be disposed of together with habitual municipal waste. Owners and users of all products marked with this symbol should take them to a specially designated collection point for waste electrical and electronic equipment.
For further information on how to dispose of waste electrical or electronic equipment once its useful life has ended, please contact your local authorities, the urban waste disposal service or the establishment in which the product was purchased.
The proper collection and disposal of old equipment contributes to preserving the natural environment and preventing potential hazards to public health.

References

• Mediclinics. Bathroom equipment manufacturers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>