perenio PEHWE20 Mini Relay User Guide
- June 12, 2024
- Perenio
Table of Contents
perenio PEHWE20 Mini Relay User Guide
GENERAL INFORMATION
Specification| Zigbee 3.0 (IEEE802.15.4), 100-240 VAC, 50/60 Hz, 1 A (2 × 0.5
A), 0.5 W max. Case: gray polycarbonate, IP20, LED indicator, pairing button.
Dimensions (L × W × H): 43 mm × 37 mm × 17 mm. Operation conditions: 0 °C to
+50 °C, 5–75 % RH (noncondensing), for indoor installation only. One wire
mounting (neutral or phase), to single-pole and bell push switches
---|---
Functions| Two-channel Mini Relay for remote switching of power supply, with
the possibility of setting the operating mode of switch
Scope of supply| PEHWE20 Mini Relay, bypass, Quick Start Guide, Warranty Card
Warranty| 2 years (Service life: 2 years)
INSTALLATION AND CONFIGURATION
ATTENTION! Mounting must be performed by a qualified electrician only, with the electricity turned off to avoid electric shock. Installation of the Mini Relay in a metal housing can impair communication with the device. The bypass is designed to be used with the Mini Relay only
- Check that the Perenio® Control Gateway / IoT Router is installed, connected to the Internet and activated in the Perenio: Smart Home and Office app.
- Unpack the Mini Relay. Deenergise the area of installation. Perform electrical connections as shown in Figure B (See the Installation and Operation Manual for wiring diagram options). Fasten wires to connectors using a 3 mm flat screwdriver (not included in the delivery package).
- Energize the area of installation – the LED indicator will start blinking blue.
- In the Perenio: Smart Home and Office app, click on the “+” icon in the “Devices” tab, select the Mini Relay from the list and follow connection tips specified on the screen. The connection process shall be performed by pressing the button on the device or by disconnecting the power network with a mechanical switch.
- To manage the device, click on its image in the “Devices” tab
SAFETY OPERATION RULES2
Installation must only be performed on a de-energized area of the power network by a qualified electrician. Please observe the operating and storage conditions, power network parameters (Voltage, load power), and the wiring diagram. Please avoid short-circuit as it could damage the device. It is not allowed to drop, throw or disassemble the device, to attempt to repair it on one’s own, to expose it to liquids. The device may be used for its intended purpose only. Do not disconnect the mains voltage for at least 5 minutes after the reset, as well as for at least 10 minutes after the firmware update process is started.
TROUBLESHOOTING
- The Mini Relay is suddenly offline: The device is out of range of the Zigbee signal. Make sure that the distance to the Control Gateway / IoT Router is within the coverage area of the relay antenna (up to 30 m in enclosed spaces, up to 100 m in free space).
- Mini Relay is offline: Supply network failure. Check the power supply and contact the local power supply company.
All information contained herein is subject to amendments without prior notification of the User. For current information and details on the device description and specification, certificates, warranty and quality issues, see relevant Installation and Operation Manuals available for downloading at perenio.com/documents. All trademarks and brand names are the property of their respective owners. Manufacturer: Perenio IoT spol s r.o., Na Dlouhém, 79, 251 01 Říčany-Jažlovice, Česko (Czech Republic). Made in China. 2 For detailed terms and conditions, refer to the Installation and Operation Manual.
OVERVIEW
-
Pairing button
-
LED Indicator
-
Connectors
-
input
- output 1
- output
- main for switches
- switch 1
- switch 2
External antenna output (external antenna may not be available in your model of device)
-
Bypass
These symbols indicate that you must follow the Waste Electrical and Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of the device, its batteries and accumulators, and its electrical and electronic accessories. According to the rules, this equipment must be disposed of separately at the end of its service life. Do not dispose of the device, its batteries and accumulators, or its electrical and electronic accessories together with unsorted municipal waste, as this will harm the environment. To dispose of this equipment, it must be returned to the point of sale or turned in to a local recycling facility. You should contact your local household waste disposal service for details.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>