PATLITE TYPE BSV-24 Slim MP3 Voice Annunciator Instruction Manual

June 12, 2024
PATLITE

PATLITE TYPE BSV-24 Slim MP3 Voice Annunciator

PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-product

Product Information

Slim MP3 Voice Annunciator

Introduction

Thank you for purchasing the Patlite Slim Model MP3 Voice Annunciator. This manual provides information on proper installation, precautionary steps, and maintenance. Please store this manual for future reference. If you have any inquiries, please contact your PATLITE Sales Representative.

Product Summary

This product is a slim-sized MP3 voice annunciator primarily used for factory automation (FA). It uses the MP3 protocol to reproduce high-quality sound voice messages. The registered voice messages can be freely rewritten, with a maximum of 15 messages that can be registered.

Safety Precautions

To prevent damage to users, personnel, and assets, please note the following safety precautions:

WARNING

Indicates an immediately dangerous condition. Failure to follow the instructions may lead to death or serious injury.

Model Number Configuration

The model number for this product is BSV-24.

Part Names and Outside Appearance

Part Names

The user manual does not provide specific information about the part names. Please refer to the product itself or contact your PATLITE Sales Representative for further assistance.

Outside Appearance

The user manual does not provide specific information about the outside appearance. Please refer to the product itself or contact your PATLITE Sales Representative for further assistance.

Installation

Front Cover

Refer to the user manual for instructions on installing the front cover of the Slim MP3 Voice Annunciator.

Panel Mounting

Refer to the user manual for instructions on panel mounting of the Slim MP3 Voice Annunciator.

Wall Mounting

Refer to the user manual for instructions on wall mounting of the Slim MP3 Voice Annunciator.

Wiring

Refer to the user manual for instructions on wiring the Slim MP3 Voice Annunciator.

Controlling The Volume

Volume Adjustment

Refer to the user manual for instructions on adjusting the volume of the Slim MP3 Voice Annunciator.

Sound Reduction Function

Refer to the user manual for instructions on using the sound reduction function of the Slim MP3 Voice Annunciator.

Various Functions and Playback Methods

Operation Modes

Refer to the user manual for information on the different operation modes of the Slim MP3 Voice Annunciator.

SD Card Operation

Refer to the user manual for instructions on using an SD card with the Slim MP3 Voice Annunciator.

Error Table

The user manual contains an error table that provides information on possible errors and their solutions. Please refer to the user manual for more details.

Binary Input Table

The user manual contains a binary input table that provides information on binary inputs and their configurations. Please refer to the user manual for more details.

Optional Sales Items

The user manual mentions optional sales items. Please refer to page 26 of the user manual for more information.

Replacement Parts

The user manual mentions replacement parts. Please refer to page 26 of the user manual for more information.

Before Requesting Repair

The user manual provides information on what to do before requesting repair. Please refer to page 27 of the user manual for more details.

Specifications

General Specifications

The user manual contains general specifications for the Slim MP3 Voice Annunciator. Please refer to page 28 of the user manual for more information.

Performance Specifications

The user manual contains performance specifications for the Slim MP3 Voice Annunciator. Please refer to page 28 of the user manual for more information.

Signal Input Specifications

The user manual contains signal input specifications for the Slim MP3 Voice Annunciator. Please refer to page 29 of the user manual for more information.

Introduction

  • Thank you for purchasing the Patlite Slim Model MP3 Voice Annunciator. Prior to installation, please read through this manual for proper installation and precautionary steps.
  • In additon, please store this manual for future reference when performing maintenance, repairs or inspections.
  • After reviewing this manual, if there are any inquiries, please direct them to your PATLITE Sales Representative.

Markings in this book

  • The bit rate of 64 kbit/s is given as the standard rate for the MP3 file. When the bit rates differ, reproduction time differs. Optional SDV-2GP should be used for the SD card. Using other SD cards is not guaranteed.
    (Refer to pg 26 “11. Optional Sales Items”)

  • Format the SD card using the FAT16 protocol. The SD card cannot be recognized if it is formatted in any form other than FAT16.

  • Terms used in this book [Message No.] is based on the playlist created by the application software, which included a collection for a maximum of 16 MP3 data files, where the channel (CH) input corresponds to the message number (i.e. Message No. 1 =CH1). For further details, please refer to the help section of the application software. In the case where the application software is not being utilized, then the CH input corresponds to the MP3 data message number.

Caution on copyright

  • Work that was recorded or copied from music CDs or other media used in public places may infringe upon copyrights and law enforcement may be imposed.
  • When using a work that was recorded or copied from music CDs or other media, be sure to obtain permission from the author.
  • In addition, copyright of audio/music data distributed or sold by PATLITE Corporation belongs to PATLITE.
  • It is strictly prohibited to copy/reprint whole or partial contents of audio/music data belonging to PATLITE Corporation, or to transfer/sell such material on computer networks etc., without permission of the rightful holder.
  • Windows® is a registered trademark of Microsoft Corporation of America, Japan and other countries.
  • The PATLITE Corporation is a member of the SD Card Association.

Product Summary

  • This product is a slim sized MP3 voice annunciator which is primarily used for, but not restricted to, factory automation (FA). Since the MP3 protocol is used as compressed data, it is possible to reproduce a high-quality sound voice message in comparison to ADPCM, by using the MPEG1-Audio Layer III (MP3).
  • Moreover, the registered voice message can be rewritten freely. (A maximum of 15 messages can be registered)

Thin Design:

  • With a thickness of 19.9mm, it can be installed in “space-saving” apparatuses.
  • High Quality Sound Playback:
  • In comparison to the ADPCM format, the MP3 Data can playback a total of 63 seconds.
  • MP3 Data Rewriting Capability:
  • With the optional SD Card, MP3 data can be freely rewritten, even out in the field.
  • Playback corresponding to various applications
  • There are eight operation modes selectable, which can select the functions in combination with the commands.
  • The modes can be freely written by using an SD Card.
  • The input can be selected between “Binary Input” and “Bit Input”.
  • The sound reduction can be controlled from a signal input and reduced with a designated sound reduction value.

Safety Precautions

In order to prevent any damage to the user and other personnel or to assets, note the following:

  • The warning indications are divided into the following classes according to the degree of danger or damage incurred when the warning is not taken into consideration and the product is not correctly used.

WARNING

  • Indicates an immediately dangerous condition: failure to follow the instructions may lead to death or serious injury.

CAUTION

  • Indicates a potentially dangerous condition: failure to follow the instructions may lead from slight to medium injury or to property or physical damage.

To operate this product properly, observe the following:

WARNING

  • Do not modify or disassemble the product. Failure to do so may result in malfunction or fire. Do not attempt to repair the product. For questions concerning our product or for when repair is necessary, refer to the end of this document for contacting your nearest PATLITE Sales Representative.
  • Be careful not to miswire this product, failure to comply can result in product failure or fire.
  • Ensure the power is in the correct tolerance for voltage supply. Failure to comply may result in malfunction or fire.
  • Request the installation and wiring be performed by a professional contractor. Otherwise, there is the possibility that fire, electric shock or falling from high places may result.

CAUTION

  • Be sure the power is disconnected before wiring or installing this product. Possibility of electric shock, short-circuiting or product failure may occur.
  • To protect the power supply and other internal circuitry, be sure to connect an external fuse.
  • Don’t install the product in a location where vibrations exceed the specifications. If installing where vibrations do exist, install the product in the upright position. Failure to comply may result in the prevention of the product detaching and falling, causing injury to a passer-by, etc.
  • This product is not guaranteed from failure produced by transportation, handling, natural disasters, etc. or the disassembly and modification contrary to warnings and notes. Moreover, please avoid the use of this product outside the contents written in this book.
  • Contrary to Warnings and Cautions indicated in this document, product failure due to mis-handling, disassembly, modifications or natural disasters, etc. is not covered by any War-ranty. Moreover, avoid any applications outside those indicated in this document.

Please

  • Indicates something to observe before using this product.

Note

  • Notice regarding supplementary information or convenient explanation is indicated.

Please

  • Do not use in an environment exposed to strong radio waves or inductance noise. Failure to the speaker may result from the inductive noise.
  • Do not use in an environment where corrosive gas is present. Possible cause of failure may occur.
  • To prevent damage from static electricity, touch hands or other body parts to metals or an earth ground to discharge the body from static charge before handling static sensitive parts, such as the SD Card.
  • Use the recommended torque when attaching parts for installation, etc.
  • Do not misplace or drop parts, such as the front cover, locking screw, etc., while performing any kind of work.
  • When this product is used for security purposes, it should be inspected daily. In case a malfunction should occur, it is recommended that you use this product together with other security products.

Model Number Configuration

PATLITE-TYPE-BSV-24-Slim-MP3-Voice-
Annunciator-fig-1

Part Names and Outside Appearance

Part Names

Refer to the following pages for the explanation of the individual functions .PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-2

  1. Front Cover
    • Remove and replace when adjusting the volume control.
  2. Mounting Screw and O-ring
  3. Mounting Bracket
    • Use when installing for Wall or Panel mount applications.
  4. Volume
    • The volume is adjustable.
  5. Lead Wire (Power Supply / Signal)
    • Wire the power supply and individual signal inputs to the proper connections.
  6. SD Card Slot
  7. It is used to insert the SD Card for rewriting MP3 data and for controlling the operation modes.[SD Card Insertion/Removal Method]
  8. When inserting the SD Card, push it all the way in until a clicking sound is heard.
  9. When extracting the SD Card, pull it straight out.
  10. Cover Locking Screw Hole
  11. M3X6 tapping screw (Cover Locking Screw)
    • It is used to prevent easy front cover access.
  12. Air Vents
    • The vents are used for heat dissipation, as well as for acoustics. Do not block the air vents.

CAUTION

  • When you insert an SD card into the ASD card slot, be careful of the direction. Also, don’t forcibly insert the SD card into the card slot. Failure to comply may result in damage to the product or the SD card.

Outside Appearance

【Outer Appearance】(mm)PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-
fig-3

Installation

This product can be panel or wall mounted. Please attach in accordance with the procedure for mounting after removing the front cover. Refer to the following figure (front view) for the mounting direction.PATLITE-TYPE-BSV-24
-Slim-MP3-Voice-Annunciator-fig-4

WARNING

  • Request the installation and wiring be performed by a professional contractor. Otherwise, there is the possibility that fire, electric shock or falling from high places may result.

Front Cover

  • When installing or adjusting the volume control to this product, please open and close the front cover in the following manner.
  1. Turn the front cover in the counter clockwise direction 45 degrees.
    • Assure there is ample rotation space available for the front cover when mounting.
  2. When attaching for wall-mounting, pull the front cover forward to remove, then pull-out the mounting screw and O-ring.
  3. Please attach the parts removed in steps 1 and 2 in the reverse order to reassemble. Attach the front cover so that the “↑UP” is on top. (Mounting Screw Recommended Torque: 0.3 N-m)
    • Use the M3X6 tapping screw indicated on the lower-right figure to fix the front cover. (Recommended Torque: 0.3 N-m)PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-5

Panel Mounting

  1. Please mount on a flat surface with a panel thickness of 1 mm to 3.5 mm for proper clamping (Refer to Installation dimensional drawing).
  2. Rotate the front cover counter-clockwise 45 degrees, and loosen the mounting screws.
  3. Referring to the “Section C Rear View” drawing, check that the mounting bracket is in position (A) before inserting the product through the front of the panel. Place the mounting brackets as indicated in position (B) and secure it with the mounting screws, clamping the mounting nut to the rear of the mounting surface. (Recommended torque: 0.3 N-m)
  4. Check that the product is securely mounted before placing the front cover back on.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-6

CAUTION

  • Be sure the power is disconnected before wiring or installing this product. Possibility of electric shock, short-circuiting or product failure may occur.
  • Ensure the installation surface is sufficient enough to handle the weight of the product, and where there is less vibration. Also, do not install in places which exceeds the specifications, such as a vehicle, etc.
  • Failure to comply may result in the prevention of the product detaching and falling, causing injury to a passer-by, etc.
  • Always use both mounting screws and tighten with the recommended torque. Failure to comply may result in the prevention of the product detaching and falling, causing injury to a passer-by, etc.
  • Do not apply a heavy load to the lead wires. Possibility of electric shock, short-circuiting or product failure may occur.
  • Do not turn the front cover more than 45 degrees. Failure to comply may result in product damage.
  • Be sure to throw away the chips generating when install the cover locking screw. When mixed inside the product, There is a case may result in malfunction.
  • Be sure to Waterproof treatment at the cover locking screw attachment point, when install the cover locking screw. There is a case may result in enter the water from it.

Wall Mounting

  1. Mount on a flat surface with a panel thickness of 1 mm to 3.5 mm for proper clamping. (Refer to the “Panel-mount Dimension drawing”)
  2. Rotate the front cover counter-clockwise 45 degrees, and pull straight out to remove, then loosen and remove the mounting screws and O-ring.
  3. Place the front cover in the same position as when removing it, insert the product onto the mounting surface from the front, then install the mounting screws from the rear of the mounting surface. (Recommended torque: 0.3 N-m)
  4. Check that the product has been properly clamped before placing the front cover back on.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-7
  • For proper mounting, the length of the mounting screw can be changed to match the thickness of the panel.

Please

  • Install the product on a flat surface with no uneven surfaces. Failure to comply will weaken its resistance to water and dust.
  • If installing the product where vibrations exist, it is recommended to make periodic inspections to ensure the mounting screws are properly tightened.
  • If installing the product where vibrations exist, it is recommended to make periodic inspections to ensure the mounting screws are properly tightened.
  • When operating the product by controlling the power ON/OFF, be sure to include a switch by which the power supply can be easily cut near the main power for safety.
  • Do not block the air vents when installing.
  • Do not apply thread locking adhesive to the cover locking screw, it may result in damage to the product.

Note

  • Depending on the mounting surface material, thickness and the volume of the product, a vibration sound may be generated from the mounting screws. Take countermeasure steps by reinforcing the mounting screws to reduce vibration.

Wiring

  • When wiring to external contacts for the signal line, use non-voltage contacts such as a relay, switch or an NPN (PNP type also available) open collector circuit. Refer to table 1 below for contact capacity.
    Refer to table 3 “Contact Capacity” on the following page.

  • Wiring Example

  • BSV-24N (NPN Transistor Type)

  • Do not short Power (+) to the CH lines. Failure do to so will result in damage to the product.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-8

  • The power (-) shares the same common as the signal ground.

WARNING

  • Double check the wiring to prevent mistakes. Failure to conform may result in product damage, resulting in damage to the circuitry or fire.

CAUTION

  • Be sure the power is disconnected before wiring or installing this product. Possibility of electric shock, short-circuiting or product failure may occur.
  • Do not pull or tug at the wires with excessive force. Failure to comply will result in damage to the product.
  • Wiring Example
    • BSV-24P (PNP Transistor Type)
  • Do not short Power (-) to the CH lines. Failure do to so will result in damage to the product.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-9

The power (+) shares the same common as the signal return line.

Table 1. Signal Contact Capacity

Current Capacity 15mA or more Leakage Current 0.1mA or less
Withstanding Voltage DC35V or more “ON” Voltage(Vsat) 1V or less

Table 2. Recommended Fuse

Rated Voltage 250V Standard Fusion Slow-blow
Rated Current 0.25A

Table 3. Inrush Current Ratings

Inrush Current 7A Max.

Please

  • To protect the power supply and other internal circuitry, be sure to connect an external fuse.
  • Be sure to check for proper wiring before connecting the power.
  • To countermeasure against interference noise, make wiring as short as possible and use shielded wires whenever possible. In addition, separate any signal lines which pass along high voltage cables or is susceptible to receive induction noises.
  • When operating the product by controlling the power ON/OFF, be sure to include a switch by which the power supply can be easily cut near the main power for safety.
  • If a non-voltage contact, such as a relay or switch etc., is used for the power supply line, consider inrush current capacity when selecting the contact. If the capacity is insufficient, it will cause pitting or welding of the contacts, causing malfunction.

Note

  • Even when starting two or more units simultaneously, a lag will occur during message playback.

Controlling The Volume

Volume Adjustment

  • The volume is adjustable from the minimum to maximum sound level.
  • The volume is to be used as the adjustment of the volume and not be used for muting.
  • Volume adjustment should be done with a small Phillips screwdriver of about 0.5mm in width.
  • The volume position is in reference to the increasing size of the “o” marking in conjunction with the po-sition of the arrow.

Note

  • As the sound increases, the possibility of distortion may also occur.
  • Due to the surrounding environment and electrical tolerances, Even with the volume adjusted to minimum, the sound level may not be zero.
  • At the time of factory shipment, the volume is set at the mid-center position (indicated as “A”) as depicted in the figure.

CAUTION

  • Turn the volume lightly when adjusting.
  • If a torque more than 0.05 N-m is applied, there is a possibility of damaging the volume control.

Sound Reduction Function

  • By using the CH4 signal line input, the sound can be reduced from 0 to -50dB during playback.
  • Refer to 15 “8-1. Operation Modes”.
  • The sound reduction during message playback, when the sound reduction input is entered, is activated within 500ms after the input.
  • Wiring Example
  • BSV-24N (NPN Transistor Type)
  • Do not short Power(+) to the CH line. Failure do to so will result in damage to the product.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-11
  • The power (-) shares the same common as the signal ground.

Various Functions and Playback Methods

Operation Modes

The operation modes for this product are selectable by choosing the operation from the eight different modes available in Table 4, and creating the corresponding input in accordance with the application. Each alphabet in the table is used at the time of creation of the mode file.
Refer to 21 “8-2-1 Operating Mode Configuration File”.
Also refer to Table 5 for the factory default modes set prior to product shipment.
Table 4. Operating Mode

A Bit Input/ Normal Playback Mode E Binary Input/ Normal Playback Mode
B Bit Input/ Input Priority Playback Mode F Binary Input/ Input Priority

Playback Mode
C| Bit Input/ Hold Playback Mode| G| Binary Input/ Hold Playback Mode
D| Bit Input/ Memory Playback Mode| H| Binary Input/ Memory Playback Mode

Table 5. Factory Default Mode Settings

Model MP3 Data Registration Contents Operating Mode
BSV-24 □ – □ No specified messages (15 pre-installed sounds) Bit Input/ Hold

Playback Mode
BSV-24 □ M- □| Four or less messages specified| Bit Input/ Normal Playback Mode
Five or more messages specified| Binary Input/ Normal Playback Mode

  • Refer to Table 6 for the reference of sound pressure for the initial 15 alarm sounds.
  • Although there are 15 sounds registered, when using all 15, it is necessary to change the operational mode into the Binary Input Mode.
  • All MP3 registered messages for the BSV-24 □ M-□ will be erased if written over.

Table 6. Initial Alarm Sound Pressure Reference

Message No.|

Alarm Name

| Reference

Sound Pressure

| Message No.|

Alarm Name

| Reference Sound

Pressure

---|---|---|---|---|---
1| Chime| 79| dB| 9| Synthesized Bell| 90| dB
2| Beep| 74| dB| 10| Stutter + Bell| 81| dB
3| Stutter| 83| dB| 11| Synthesized Melody| 86| dB
4| Bell| 89| dB| 12| Call Sign| 91| dB
5| Yelp| 85| dB| 13| Inverted Reveille| 87| dB
6| Rapid Hi Lo| 87| dB| 14| Galactic Motor| 84| dB
7| Melody Chime| 90| dB| 15| Two Tone| 83| dB
8| Synthesized Piano| 89| dB|

  • Measurement conditions: The product is attached to the center of a 300mm by 300mm board at a distance of 1 meter away from the front of the product.
  • These values were recorded under controlled conditions and are for reference only. Actual sound pressure will depend on the surrounding environment.

Signal Input

  • There are two kinds of signal inputs, bit input and binary input. The difference in a signal input is explained below.

Bit Input

  • The short-circuiting of the signal lines CH1 through CH4 to the common line will playback MP3 data.
  • Signal lines CH1 to CH4 corresponds to message Numbers 1 to 4, respectively.
  • A maximum of 4 message channels can be played back. (When the sound reduction function is active, a maximum of 3 message channels can be played back)
  • When two or more inputs are simultaneously entered, the input is chosen in accordance to priority, in which the higher number is of higher priority.
  • In the memory playback mode, the memory saves the input based on the priority of the higher number.
  • When the sound reduction function is activated, the CH4 signal line turns into the sound reduction signal line.
  • Refer to pg 14 “7-2. Sound Reduction Function”.

The order of input priority is from right to left: CH4 > CH3 > CH2 > CH1 PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-12

Refer to the corresponding playback mode for a detailed explanation of the time chart.

Binary Input

  • The short-circuiting of the signal lines CH1 through CH4 to the common line will playback MP3 data.
  • About the relation between message No. to reproduce and CH signal line input, refer to pg. 25 “10. Binary Input Table”
  • A maximum of 15 message channels can be played back. (When the sound reduction function is active, a maximum of 7 message channels can be played back)
  • When the sound reduction function is activated, the CH4 signal line turns into the sound reduction signal line.
  • Refer to pg. 14 “7-2. Sound Reduction Function”PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-13
  • Refer to the corresponding playback mode for a detailed explanation of the time chart.

Playback Mode

  • The operation for reproducing MP3 data with this product can be chosen from four playback modes of “Normal Playback”, “Input Priority Playback”, “Hold Playback”, and “Memory Playback”.
  • Normal Playback Mode MP3 data is reproduced in correspondence to an input. When an input is a one shot, the corresponding message number is reproduced once, and playback is repeated when the input is maintained.
  • Any channel input is ignored during MP3 data playback.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-14
  • Input Priority Playback Mode
  • During an MP3 message playback, the message will stop when a different channel input is entered and the message will continue after the previous channel’s message has ended.
  • Even if an input is held, playback is only played once.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-15

Hold Playback Mode

  • The message will only play back while the input is held on. Playback will stop once the input is removed.
  • While the input is held on, the message playback will be repeated.
  • The higher channel input takes the highest priority.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-16
  • Playback was stopped and the wavy line means the message No. corresponding to the input channel was played.

Memory Playback Mode

  • During playback, when a channel input is entered, the message number corresponding to the input is put into memory. When the previous message playback is terminated, the message number entered afterward into the memory will be played next. After two channel inputs, any other input is ignored until the memory space is available.
  • While the input is held on, the message playback will only be played once.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-17

SD Card Operation

  • SD cards can be used and the MP3 data and the memory inside the main unit can be used to control the operation modes.
  • The following is necessary for rewriting MP3 data.
  • The SDV-2GP type which saves the data for rewriting
  • Refer to pg. 26 “11. Optional Sales Items”
  • Refer to the PATLITE Playlist Editor “Help” menu for setting up the playlist and editing functions.
  • Personal computer
  • SD card reader/writer
  • Application Software (PATLITE Playlist Editor)
  • Even if the application software is not used, the data can still be created

Note

  • When using the PATLITE Playlist Editor, even when the text file is registered, sometimes the MP3 file is not
  • registered, therefore will not playback.
    • (Refer to the PATLITE Playlist Editor Help Menu in the software)

Operating Mode Configuration File

  • The file for choosing the operational mode can be created and it can be changed into arbitrary operational modes just by rewriting.
  • Please refer back to pg. 15 “8-1. Operation Modes”
  • The operating mode configuration file can be created by using the file name of a text file as indicated belowPATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-19

Example 1)

  • MODE-C.txt — Configuration file is set for the bit input hold playback mode (sound reduction function is deactivated)

Example 2)

  • MODE-H05.txt — Configuration file is set for the binary input memory playback mode (sound reduction function is activated for a -5 dB reduction)
  • Since the sound pressure changes with the surrounding environment, there is no guarantee the change in the sound reduction value will make any noticeable difference.
  • The file names can use both capital and small letters.
  • The contents of text file is Unnecessary because text file for setting is used the File Name only.

MP3 Data

  • There are two ways to rewrite MP3 data. Please refer to the following considerations when selecting the creation method for data.
  1. When using the application software
    • Uses the application software to create a playlist file, then creates a playlist file to run with the MP3 data.
  2. When not using the application software
  • A file can be created out of the MP3 data without the application software. A maximum of 15 selections can be set up.
  • Please refer to the following table for the difference between the two methods when considering whether the application software will be used.
  • Table1 Comparison Chart for the PATLITE Playlist Editor vs. MP3 Data application
Item When to use it When not to use it

Every MP3 data message is played

| A maximum of 16 selections can be set up (It is combined freely and can playback in order)|

Only one selection can be set up

Individual MP3 data settings are made| The volume, interval and number of times repeated can be designated.| Setup is not possible

Refer to the following diagram and examples on how to create the MP3 data file PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-20

  • Example 1) 003.mp3 — MP3 data which can be assigned to message No.3
  • Example 2) 013.mp3 — MP3 data which can be assigned to message No.13
  • The file names can use both capital and small letters.

File Arrangement

  • Refer to pg. 21 “8-2-1 Operating Mode Configuration File” and pg. 22 “8-2-2 MP3 Data”
  • Data rewriting preparation is completed by sorting and arranging files in the SD card.
  • Moreover, the operational mode configuration files and MP3 data files can be individually rewritten. In that case, please arrange only one file to rewrite among the following data.
  • When using either the application software with the file, or not using it, if in the case it is intermingled, the file using the application will take priority when read.

When application software is used:

Please do not change the MP3 data file name when setting it up from the application software.
When application software is not used:

Rewriting procedure for setting MP3 data and Operation Mode

  1. Place the product into its standby condition (having no playback or signal inputs).
  2. Insert the SD card with the rewritten and saved data into the SD card slot.
    • Refer to pg. 21 “8-2. SD Card Operation” for rewriting and saving the data.
  3. Rewriting will start when the SD card is inserted into the SD card slot.
    • When rewriting starts, a short beep sound will be heard to indicate rewriting has started. When a long beep sound is heard, it indicates the rewriting sequence is complete and the SD Card can be removed from the slot, and when there is an error, the alarm will sound in combination with the contents of the error.
    • (Refer to pg. 25 “9. Error Table”)
    • The data rewriting procedure should take a maximum of 60 seconds.
    • If the power is turned off, or the SD card is extracted during data rewriting, the rewriting procedure will not be completed. In this case, please start over to rewrite again.
    • When rewriting, all previous saved MP3 data will be erased.
  4. After the MP3 data rewrite sequence has been completed, check that the data has been rewritten properly.
    • When MP3 data playback is not normal
    • Please create data after formatting the SD card for FAT16.
    • Please check whether any ID tags are attached. A tag may cause playback malfunctions.
    • Depending on the MP3 player, there is that the ID tag is added automatically.

Please

  • The optional SDV-2GP type should be used for the SD card. The use of other SD Cards is not guaranteed by PATLITE.
  • Format the SD card using the FAT16 protocol. The SD card cannot be recognized if it is formatted in any form other than FAT16.

Note

  • [Formatting the SD card]
  • Please open the “My Computer” file in the personal computer, right-click the drive containing the SD card, and choose “format.” The type of format used should be either FAT or FAT16.
  • Caution: The execution of a format will eliminate all the data in the SD Card.PATLITE-TYPE-BSV-24-Slim-MP3-Voice-Annunciator-fig-23

Error Table

  • When an error has occurred, an alarm will sound. Refer to the following table for troubleshooting and its solution.
  • The type of alarm changes in conjunction with the type of error.
  • The alarm sound is not audible if the volume is not at a nominal level.
  • Even after the items below do not solve the problem, refer to the last page for assistance from your PATLITE Sales Representative.
Error Sound Error Name Solution

Four short beeps (Short Beep x4)

|

Hardware

Error

| •   The SD Card is not pushed all the way into the socket, or there is a loose connection. Try re-inserting the SD Card.

•   The contents on the SD Card is not readable. The SD card may be formated for something other than FAT16. Reformat the SD card for FAT16 and reload the message data.

Three long beeps (Beep x3)

|

MP3 Data Related Error

| •   The playlist file on the SD card may be corrupted. Rewrite the data again, then

re-insert the card into the product.

•   The MP3 data may not be in the data folder to be registered for the playlist file. Confirm the MP3 data is on the SD card before re-inserting it.

•   The MP3 data capacity may have exceeded the memory capacity of the product.

rewrite the data and verify the capacity does not exceed the specifications.

Three short bursts

(Short-burst beep x3)

| Operating Mode

Data Error

| •   The operating mode configuration file may be written incorrectly. Verify the file

name before re-inserting it into the product.

Binary Input Table

Terminal

Voice      CH

Message

| ****

CH1

| ****

CH2

| ****

CH3

| ****

CH4

---|---|---|---|---
No. 1| ●|  |  |
No. 2|  | ●|  |
No. 3| ●| ●|  |
No. 4|  |  | ●|
No. 5| ●|  | ●|
No. 6|  | ●| ●|
No. 7| ●| ●| ●|
No. 8|  |  |  | ●
No. 9| ●|  |  | ●
No. 10|  | ●|  | ●
No. 11| ●| ●|  | ●
No. 12|  |  | ●| ●
No. 13| ●|  | ●| ●
No. 14|  | ●| ●| ●
No. 15| ●| ●| ●| ●
The “●” mark indicates a COM to channel (CH) terminal contact.

Optional Sales Items

  1. SD Card (MP3 Voice Message Upload) Model SDV-2GP

Replacement Parts

Part Name

Front Cover- Off-white
Front Cover- Dark Grey
Front Cover- Silver
Mounting Screw (2 O-rings included)

Parts available to customers for replacement, or repair.

Before Requesting Repair

Problem Where to Check



No Sound Coming

out of Speaker

| •   Make sure the polarity and rated voltage for the wiring is correct.

(Refer to pg. 11 “6. Wiring”)

•   Make sure the signal input wiring connections are correct.

(Refer to pg. 11 “6. Wiring”)

•   Double check the volume.

(Refer to pg. 13 “7-1. Volume Adjustment”)

•   Check that the proper operating mode is written into the product.

(Refer to pg. 15 “8-1. Operation Modes”)

•   Verify the SD card contents. (Refer to pg. 21 “8-2. SD Card Operation”)



A different channel plays back

| •   Make sure the input wiring connections are correct.

(Refer to pg. 11 “6. Wiring”)

•   Make sure the input signals are correct.

(Refer to pg. 15 “8. Various Functions and Playback Methods” or, pg. 25 “10. Binary Input Table”)

•   Double check the data in the SD card.

(Refer to pg. 21 “8-2-1 Operating Mode Configuration File”)



The sound is low

| •   Check whether the sound reduction is active and the inputs are on or not.

(Refer to pg. 14 “7-2. Sound Reduction Function”)

•   Double check the volume. (Refer to pg. 13 “7-1. Volume Adjustment”)

•   Check the sound level of the MP3 data and refer to the MP3 editing software document before

editing.



Cannot rewrite the

voice message

| •   Make sure the contents in the SD card are correct. (Refer to pg. 15 “8-1. Operation Modes”)

•   Make sure the data size did not exceed 508KB. (Refer to pg. 28 “14-2. Performance

Specifications”)

•   Make sure the format for the SD card is FAT16. (Refer to pg. 24 “8-2-4 Rewriting procedure for setting MP3 data and Operation Mode”)

•   Make sure the write protect to the SD card is disabled. (Refer to pg. 24 “8-2-4 Rewriting procedure for setting MP3 data and Operation Mode”)


The sound reduction function doesn’t operate

| •   Check whether the contents of the SD card is correct. (Refer to pg 14 “7-2. Sound Reduction

Function”)

•   Check whether the SD card is formatted for FAT16. (Refer to pg. 24 “8-2-4 Rewriting procedure for setting MP3 data and Operation Mode”)

•   Check whether the operating mode configuration file is correct. (Refer to pg. 21 “8-2-1 Operating Mode Configuration File”)

The Operating Mode doesn’t operate at the mode it was set for.| •   Check whether the operating mode configuration file is correct. Refer to pg. 21 “8-2-1 Operating Mode Configuration File”.
The SD card is not being read| •   Make sure the SD Card is from PATLITE. (Other SD Card’s compatability is not guaranteed.)

•   Make sure the write protect to the SD card is diabled. (Refer to pg. 24 “8-2-4 Rewriting procedure for setting MP3 data and Operation Mode”)


MP3 data is not being played back correctly

| •   Check the bit rate and sampling frequency of the MP3 data. (Refer to pg. 28 “14-2. Performance Specifications”)

•   Check whether MP3 tags were attached to the MP3 data. (Refer to pg. 28 “14-2. Performance Specifications”)

Even after proper connections and settings are performed, if the product does not operate properly, please see the information on the last page of this document to contact your PATLITE Sales Representative.

Specifications

General Specifications

Model Name BSV-24 □□ – □
Rated Voltage 12 to 24VDC
Operating Voltage Range 10.8 to 26.4VDC
Power Consumption Max. 3.5W (Test Conditions: DC24V, Max. Vol., Ch 1 to 4 on,

1kHz sine wave at

-6dB)

Operating Temperature Range| -10oC to +50oC
Storage Temperature Range| -20oC to +60oC
Relative Humidity| 85% RH or less (No Condensation)
Protection Rating| Panel Mount| IP54 (Upright Direction Only)
Wall Mount| IP20
Insulation Resistance| More than 1MΩ at 500V DC between the terminals and chassis
Withstanding Voltage| 500VAC applied for 1 minute between terminals and chassis without breaking

insulation

Inrush Current Rating| Maximum of 7A
Vibration Resistance| 70m/s2 at 30Hz in the X, Y and Z directions for 2 hours each
Mass (Tolerance: 10%)| 100g


Standards, Conformities

| RoHS Directive (EN50591)

EMC Conformity (EN61000-6-4, EN61000-6-2)

Complies to FCC CFR Title 47 Part 15 Subpart B

Performance Specifications

Sound Pressure Level| No more than 87 dB (Panel Mount)| No more than 85 dB (Wall Mount)
---|---|---
Measurement Conditions: The product is attached to the center of a 300mm by 300mm board with a 1kHz sinusoidal wave played back at -6dB, and the decibel meter is set 1 meter away from the front of the product.

  • The sound pressure level will vary with the surrounding environment and message contents.
    Volume Control| Volume Adjustment: Minimum to Maximum
    Sound Reduction Function: -1dB to -50dB (CH4 is designated as the sound reduction input)
    Number of Playback Messages| Bit Input: 4 (3) / Binary Input: 15 (7)

  • The brackets indicate channels available when the sound reduction function is activated.

Initial Registered Data| The following alarm data is loaded when no set messages are ordered
No. 1| Chime| No. 2| Beep| No. 3| Stutter| No. 4| Bell| No. 5| Yelp
No. 6| Rapid Hi Lo| No. 7| Melody Chime| No. 8| Synthesized

Piano

| No. 9| Synthesized Bell| No. 10| Stutter + Bell
No. 11| Synthesized Melody| No. 12| Call Sign| No. 13| Inverted

Reveille

| No. 14| Galactic

Motor

| No. 15| Two Tone

  • All MP3 registered messages for the BSV-24 □ M- □ will be erased if written over.
    Audio File| MPEG1-Audio Layer III (MP3)
    Bit Rate| 32kbit/s and 64kbit/s (Standard): Fs=44.1kHz
    Maximum Playback Time| Total of 63 seconds (at the standard bit rate of 64kbit/s)
    Audio Startup Time| About 300ms (After a signal input or when the power supply is activated)
    Internal Memory Size| 508 KB (MP3 data sum total)
    Compatible Memory Card| SD Card Recommended Part: SDV-2GP (Sold Separate)
    SD Card Format| FAT16
    Application Software| Patlite Playlist Editor
    Mode Change| Selectable for a file name with an empty text file.

Signal Input SpecificationsPATLITE-TYPE-BSV-24-Slim-MP3-Voice-
Annunciator-fig-24

Due to changes, improvements, etc., the contents of this manual may change without advance notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals