HAY Bonbon Shade Pendant Light Instruction Manual
- June 12, 2024
- HAY
Table of Contents
HAY Bonbon Shade Pendant Light
Product Information
The Bonbon Shade is a lighting product designed by Ana Kras. It is intended to be used with the HAY Cord Set/Cord Set Table or a similar cord set. It is recommended to use this product with an LED bulb. The fitting type for the bulb is E27 (EU) or E26 (US) and the recommended power range is 8-15W. The color temperature of the light emitted is warm white.
HAY emphasizes that using incorrect bulbs may lead to accidents, injuries, or damages, and therefore, it is important to follow the provided instructions for safe installation. The product is specifically designed for use with LED- based light sources only. It is suitable for indoor use only.
Product Usage Instructions
- Unpack all the parts and ensure that you have received all the listed parts.
- Unscrew and remove the ring from the E27 (EU) or E26 (US) bulb holder of your chosen cord set.
- Place the shade over the bulb holder with the bulb holder facing downwards.
- Carefully lead the bulb holder through the hole at the top of the shade.
- Screw the shade’s lower ring back onto the bulb holder to secure the shade’s frame to the bulb holder.
- Screw an LED light bulb into the bulb holder, ensuring that the electricity is switched off to avoid damaging the bulb.
- If using a table lamp, carefully pull the table lamp cord set through the bottom of the weaving by gently separating the yarn threads.
Care and Maintenance
To clean and maintain the shade, do not use wet or damp cloths. Instead, use a dry, lint-free cloth or duster to remove any dirt.
It is important to ensure that the power supply to the circuit is turned off before installing the product. In some countries, electrical installation may need to be carried out by authorized electricians or contractors. Please check with your local authority for guidance.
The product must not be modified in any way, and HAY does not accept responsibility for any modified or tampered products.
Additional Information
For detailed care and maintenance instructions, please scan the QR code provided or refer to the Care & Maintenance guide on the hay.dk/downloads website.
For more information about the Bonbon Shade, you can also scan the QR code provided or visit the HAY website at www.hay.com.
Contact Information:
Address: Havnen 1, 8700 Horsens, Denmark
Phone: +45 3164 6000
Email: hay@hay.com
Date: 12/01/2023
GENERAL INFORMATION
TECHNICAL DATA
- This product is designed to be used in conjunction with the HAY Cord Set/Cord Set Table, or a similar cord set. HAY recommends using this product with a LED bulb.
- FITTING TYPE | E27 (EU) or E26 (US)
- POWER (W) | 8-15W
- COLOUR TEMPERATURE | Warm white
- HAY will not accept any responsibility for any accidents, injuries or damages that occur due to the use of incorrect bulbs.
ATTENTION
- Ensure that the power supply to the circuit has clearly been turned OFF before installing the product. In some countries, electrical installation must be carried out by authorised electricians/contractors; please check with your local authority for guidance.
- The product must not be modified in any way. HAY accepts no responsibility for any products that have been modified or tampered with. This lamp is designed for indoor use only.
- NOTE | The cord sets for the lamp are sold separately and are available in two designs – a table/floor variant with an in-line rocker switch, and a pendant variant for ceiling lamps. Both variants can be used with the different lamp shade sizes and are not supplied with a bulb.
- If you are using this shade in conjunction with the HAY Cord Set, please follow the instructions that have been provided with it for safe installation.
- The Bonbon Shade is designed to be used with LED based light sources only.
CARE AND MAINTENANCE
Do not use wet or damp cloths for cleaning and maintaining the shade. Please use a dry, lint-free cloth or duster to remove any dirt.
PARTS
-
Unpack all the parts and check that you have received all the parts listed. Unscrew and remove the ring from the E27 (EU) or E26 (US) bulb holder of your chosen cord set.
-
Place the shade over the bulb holder, with the bulb holder facing downwards.
-
Carefully lead the bulb holder through the hole at the top of the shade, and then screw the shade’s lower ring back onto the bulb holder to secure the shade’s frame to the bulb bolder.
-
Screw an LED light bulb into the bulb holder. Ensure the electricity is switched off before fitting the bulb to avoid damaging it.
-
Table Lamp only.
Carefully pull the table lamp cord set through the bottom of the weaving by gently separating the yarn threads.
CARE & MAINTENANCE
Our Care & Maintenance offers guidance for optimal maintenance of your HAY product. It includes advice and instructions on cleaning and caring for specific materials to prolong the life of your lighting.
Please find our Care & Maintenance guide by scanning the QR code
You can find more relevant information on Bonbon Shade by scanning the QR code
You can also find the same information here hay.dk/downloads
Havnen 1 8700 Horsens Denmark
+45 3164 6000 /
hay@hay.com
www.hay.com
References
- HAY.dk – latest products, designer news and retailer info
- HAY – Danish-Inspired Furniture + Accessories for Modern Living
- HAY.dk – latest products, designer news and retailer info
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>