saxby lighting 103850 MW Sensor Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
lighting 103850 MW Sensor
Instruction Manual
Instruction manual
MW SENSOR
103850
103850 MW Sensor
Settings
Detection area, hold time and daylight sensor can be set using DIP switches on
the sensor. Note that reducing the detection area will also reduce the
sensitivity.
-
Detection area
I: up to 100%
I upt075%
111z up to 50%
IV: up t0 25% -
Hold time
Refers to the time period the lamp remains at 100% illumination after no motion detected
I 5s
II:13S
III: 1min
IV: 3mins
V: 20mins
VI: 30mins -
Daylight sensor
The sensor can be set only to allow the lamp to illuminate below a defined ambient brightness threshold. The settings are as follows:-
I: 2Lux, dakness operation only or open at 10Lux and close at 20Lux
II: 10Lux, dakness operation only or open at 25Lux and close at 75Lux
I: 25Lux, twilight operation or open at 50Lux and close at 100Lux
IV: 50Lux, twilight operation or open at 100Lux and close at 200Lux
V: 100Lux, brightness operation or open at 150Lux and close at 300Lux
VI: Disable When set to Disable mode, the daylight sensor will switch on the lamp when motion is detected regardless of ambient lamp levels. -
Mode
Select motion mode or photocell mode.
I: Motion function is available only.
Il: Photocell is available only.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish For your safety, always switch off
the power supply before changing lightbulbs, or cleaning
‘Thank you for purchasing this light fitting. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this
product. Please retain these instructions for future reference.
Warning
Please read these instructions carefully before commencing any work
“This unit must be fitted by a competent and qualified electrician
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
If you are in any doubt, please consult a qualified electrician
The sensor should not be modified in any way.
The sensor should be connected to a stable power supply (220-240V~50Hz).
Microwaves cannot pass through metal or brick walls if thicker than 20cm. They
will pass through thinner walls but there will be some attenuation.
Installation inside a glass of plastic housing will resulting a reduction of
detection sensitivity. Expect a reduction of 20% for every 3mm of thickness.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP
rating of the product.
- If installing directly to product, create knock out hole in desired location so microwave sensor can be installed.
- Remove nut from thread and place threaded end through created knock out. Refit nut from other side and tighten o secure.
- Wire as detailed wiring diagram.
Wiring
Having correctly identified the wiring from your existing light fitting,
connect to the connection block inside the product in the following way:
Please note: termination is not supplied. If you are not connecting the sensor
to another unit then the switched live (S/L) wire will need to be terminated,
Check that…
- You have correctly identified the wires.
- The connections are tight.
- No loose strands have been left out of the connection block
Technical Specifications
| Voltage: | 220-240V 50Hz a.c. |
|---|---|
| Load: | 400W (inductive), BOOW (resistive) |
| HF System: | 5.8GHz+75MHz, ISM wave band |
| Transmitting Power: | <0.5mwW |
| Power Consumption: | < 0.5W (standby) |
| Detection zone: | Max. (D x H): 12m x 10m |
| Detection sensitivity: | 25% /50% / 75% / 100% |
| Hold Time: | 5s/30s/1min / 3mins / 20mins / 30 mins. |
| Daylight sensor. | 2Lux /10Lux / 25Lux/ 50Lux / 100Lux / Disable |
| Daylight open/close: | 10Lux/ 50Lux; 25Lux / 75Lux; 50Lux / 100Lux; 100Lux / |
200Lux; 150Lux / 300 Lux; Disable.
Mounting height:| 6m Max.
Motion detection:| 0.5~3m/s
Detection angle:| 150° (wall installation) / 360° (ceiling installation)
Operating temperature:| -25°C to +60°C
IP rating:| 65
Override Function
Quick switch ON/OFF 3 times within 2sec to override sensor function. Lights
will switch on all the time. Power off and on again to recover sensor
function.
Factory Setting
Detection Area: 100%, Hold Time: 5S, Daylight Sensor: Disable, Mode Settings:
Motion
Detection Pattern
| 1) Ceiling mounting | 2) Walling mounting |
|---|---|
| Horizontal installation: 2m |
Sensor range setting: 100%/75%/50%/25%
V1 29/07/2022
UK Manufacturer: BH17 78Y
EU Manufacturer: Brilliant AG,
Brilllantstrasse 1, D-27442 Gnarrenburg
www.seabylighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>