HALL TECHNOLOGIES HT-AIM-70 4K 60Hz 4:2:0 HDBT Extender User Manual

: June 12, 2024
: HALL TECHNOLOGIES

Table of Contents

HALL TECHNOLOGIES HT-AIM-70 4K 60Hz 4:2:0 HDBT Extender
Product Information
Usage Instructions
Important Safety Instructions
Introduction
Package Contents
Connectors & Indicators
Product Wiring and Connection Diagram
Applications
Setup
Troubleshooting
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HALL TECHNOLOGIES HT-AIM-70 4K 60Hz 4:2:0 HDBT Extender

Product Information

The HT-AIM-70 is a slimline HDBaseT extender pair that can transmit HDMI signals of up to 4K 60Hz (4:2:0 8-bit) along 70m of category cabling. It comes with a transmitter unit and a receiver unit, along with a power adapter, IR emitter cable, IR receiver cable, 3.5mm 3-pin Phoenix connector, and mounting brackets. The extender pair also features bi-directional PoC two-way IR and RS232 pass-through.

Features

Transmits up to 4K@60Hz 4:2:0 8-bit and HDCP2.2 over a single category cable
Uses Cat6a/7 cable to extend 4K@60Hz 4:2:0 8-bit up to 40m/130ft and 1080P up to 70m/230ft
Uses Cat5e/6 cable to extend 4K@60Hz 4:2:0 8-bit up to 35m/115ft and 1080P up to 60m/200ft
Bi-directional PoC (Power over Cable) with one power adapter at either end
Supports bi-directional IR and RS232 pass-through

Usage Instructions

Before using the HT-AIM-70, please read the important safety instructions mentioned in the user manual carefully. Ensure that the apparatus is not exposed to rain, moisture, dripping or splashing, and is well ventilated. Do not obstruct its ventilation openings, install it near any heat sources, or place sources of naked flames on it. Clean the apparatus only with a dry cloth, and unplug it during lightning storms or when unused for long periods of time. Protect the power cord from being walked on or pinched particularly at plugs, and only use attachments / accessories specified by the manufacturer.

To use the extender pair, follow these steps:

Connect the transmitter unit to the source device (e.g. Blu-ray player) using an HDMI cable.
Connect the receiver unit to the display device (e.g. TV) using an HDMI cable.
Connect the transmitter and receiver units using a category cable (Cat6a/7 or Cat5e/6).
Connect the IR emitter and receiver cables to the transmitter and receiver units respectively.
Connect the power adapter to either end of the extender pair, ensuring that bi-directional PoC is enabled.
Turn on the source and display devices.

With the built-in control pass-through, users can control the source from the display’s location or control the display from the source’s location. The small form factor of the extenders makes them easy to install in many locations.

Important Safety Instructions

Do not expose this apparatus to rain, moisture, dripping, or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure the unit is well-ventilated.
To prevent risk of electric shock or fire hazard due to overheating, do not obstruct the unit’s ventilation openings with newspapers, tablecloths, curtains, and similar items.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not place sources of naked flames, such as lighted candles, on the unit.
Clean this apparatus only with dry cloth.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Protect the power cord from being walked on or pinched particularly at plugs.
Only use attachments/accessories specified by the manufacturer

Introduction

OVERVIEW
The AIM-70 is a slimline HDBaseT extender pair that can transmit HDMI signals of up to 4K 60Hz (4:2:0 8-bit) along 70m of category cabling. CAT6 cable supports 4K 60Hz (4:2:0 8-Bit) up to 35m and 1080p 60Hz HDMI signals can also be extended up to 60m. CAT6A / 7 cabling offers increased distances of 40m for 4K 60Hz (4:2:0 8-Bit) resolutions and 70m for 1080p 60Hz. The AIM-70 also features bi-directional PoC two-way IR and RS232 pass-through.
With the built-in control pass-through, users can control the source from the display’s location or can control the display from the source’s location. And, with their small form factor, the extenders are easy to install in many locations.

FEATURES

Up to 4K@60Hz 4:2:0 8-bit and HDCP2.2 over a single category cable.
Using a Cat6a/7 cable extends 4K@60Hz 4:2:0 8-bit up to 40m/130ft and 1080P up to 70m/230ft.
Over a Cat5e/6 cable, extends 4K@60Hz 4:2:0 8-bit up to 35m/115ft and 1080P up to 60m/200ft.
Bi-directional PoC (Power over Cable) with one power adapter at either end.
Supports bi-directional IR and RS232 pass-through.

Package Contents

HT-AIM-70

1x Transmitter Unit
1x Receiver Unit
1x Power Adapter (DC 18V 1A)
1x IR Emitter Cable
1x IR Receiver Cable
2x 3.5mm 3-Pin Phoenix Connector
4x Mounting Brackets (with screws)

Connectors & Indicators

HT-AIM-70 FRONT PANEL

HALL-TECHNOLOGIES-HT-AIM-70-4K-60Hz-420-HDBT-Extender-
FIG-1

No.	Name	Description
1	POWER	· On: The device is powered on.

· Off: The device is powered off.

2| STATUS| · On: The device is working properly.

· Off: The device is not working properly.

3

| ****

HDCP

| · On: HDCP protected content is being transmitted.

· Blinking: Non-HDCP protected content is being transmitted.

· Off: No content is being transmitted.

4| LINK| · On: HTBaseT link is normal.

· Blinking/Off: No HDBaseT link or link error.

HT-AIM-70 REAR PANEL

HALL-TECHNOLOGIES-HT-AIM-70-4K-60Hz-420-HDBT-Extender-
FIG-2

No.	Name	Description
1	POWER	DC 18V power supply. (Only one side needs to be powered.)
2	HDBT IN	HDBaseT input, connected to the transmitter output via Cat5e/6/7

Product Wiring and Connection Diagram

HALL-TECHNOLOGIES-HT-AIM-70-4K-60Hz-420-HDBT-Extender-
FIG-3

Applications

A laptop, or other HDMI source, is connected to the HDMI input on the HT- AIM-70-TX and then transmitted over the category cable to the HT-AIM-70-RX, where a display, connected to the HDMI output, shows the HDMI source. Control via RS232 or IR is also passed through the category cable for display control.

Note: In this application the HT-AIM-70-RX is locally powered and providing power via PoC (Power over Cable) to the HT-AIM-70-TX. Only one side needs to be powered, meaning the local power supply could be moved to the HT- AIM-70-TX if that is more convenient for installation.

HALL-TECHNOLOGIES-HT-AIM-70-4K-60Hz-420-HDBT-Extender-
FIG-4

Setup

INSTALLATION

Note: Before installation, please ensure the devices are disconnected from the power source.

To install the device on a surface:

Secure the included L-bracket mounts to each side of the transmitter/receiver using the included screws.
The bottom part of the L-bracket will slightly raise the transmitter/receiver and will create a small gap between the device and the mounting surface.
Using the appropriate hardware (not included), mount the bottom of the L-brackets to the desired surface.

Troubleshooting

Problem Type	Problem	Options

Video

|

No video on display

| Confirm the connectors are properly seated on each device
Confirm at least one side (typically the receiver) has local power connected
Test the category cable to confirm proper pinout and no shorts in the cable
Confirm the distance between the transmitter and receiver does not exceed specifications (depending on the desired resolution)
Confirm the HDMI input of the display is correctly selected
Confirm the connected source is sending video to the HT-AIM (i.e. verify laptop is in duplicate or extend mode)