INOVAAIR AirClean DV20 Air Purifier User Manual

June 4, 2024
INOVAAIR

INOVAAIR-logo

INOVAAIR AirClean DV20 Air Purifier

INOVAAIR-AirClean-DV20-Air-Purifier-product-image

INOVAAIR-AirClean-DV20-Air-Purifier-1

Important safety instructions

Please read these instructions before operating the InovaAir® System and keep for future reference.

To reduce the risk of fire, electric shock, or injury
  1. Do not detach motor-outlet module until the system has been switched off.
  2. Disconnect power, or unplug, before cleaning, performing any maintenance or replacing a filter.
  3. Use caution when moving the air purifier to avoid injury. We advise removing the filters prior to lifting or transporting the system.
  4. Do not operate unless all components are fully assembled, securely latched and in the upright position. Failure to do so may result in serious injury.
  5. Leave a distance of at least 100mm between the appliance and the nearest wall to allow for adequate air circulation.
  6. Always keep air intake and outlet of the unit unobstructed.
  7. Do not use near water or moisture or the immediate surroundings of a bath, shower, or swimming pool.
  8. Do not immerse the air purifier in water or any other liquid.
  9. Do not let objects, or liquid, enter the product.
  10. Do not handle any part of the appliance or plug with wet hands.
  11. Do not install near any heat sources.
  12. Do not operate this appliance if it has a damaged cord or plug, is not working correctly, or has been dropped.
  13. Do not use this appliance if it has been damaged or submerged in water.
  14. The appliance is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  15. If the supply cord is damaged, it must be replaced with a new cord. Contact our support team for a replacement.
  16. Keep power cord away from heated surfaces.
  17. Refer all servicing to qualified InovaAir® service personal. Servicing is required when the product has been damaged in any way. Do not attempt to service this product yourself. Opening or removing covers may expose you to dangerous voltages or other hazards and may void warranty.
  18. Unplug the air purifier during lightning storms or when unused for long periods.
  19. Do not use this appliance as sole protection against harmful pollutants.
  20. Do not use outdoors.
  21. Keep the appliance away from flammable liquids, vapours, air fresheners and essential oils.
  22. Do not use in explosive or flammable environments.
  23. Use only on solid, horizontal, and stable surfaces.
  24. Do not operate in high temperatures over 40°C

Introducing your InovaAir® AirClean system

Inside the DV20 box, you will find the InovaAir® unit, consisting:

  • DV20 System Case/Motor
  • Filter Base Plate (detachable)
  • Power Cable (located in base of box)
  • DV20 Pre-filter (pre-installed)
  • DV20 HEPA Filter (pre-installed)

INOVAAIR-AirClean-DV20-Air-Purifier-2

How your AirClean system works

INOVAAIR-AirClean-DV20-Air-Purifier-3

  • Air is drawn into the system through the sides of the unit.
  • Air passes through the fine dust pre-filter.
  • Air passes through the H13 HEPA filter which removes dust, allergens and sub-micron fine particle matter.
  • The purified air is then returned to the room via the high air-flow diffuser.

The digital controller

Connect the power cord supplied to the power cord inlet on the back of the unit, switch the Main Power On/Off Switch to ON. The system will initiate startup power cycle and all LEDS will illuminate momentarily. INOVAAIR-
AirClean-DV20-Air-Purifier-4

InovaSmartTM Digital Controller
Designed for intuitive operation the digital interface on your InovaAir system continuously keeps track of filter life by monitoring system usage based on hours of use and speed of the fan during operation.

  1. FILTER CHECK
    Filter Life indicator lights will illuminate separately when the “Filter Check” button is pressed and a number will appear in the LED display showing how many month(s) of life each filter has remaining.
    Filter longevity based on 24 hour usage: Pre-filter: 6 months; HEPA Filter: 36 Months
    Please note. The filter replacement intervals are calculated based on the current fan speed. Running the system at higher fan speeds will result in a reduced replacement
    interval.

  2. EXPRESS CLEAN
    When pressed this allows the user to preselect maximum speed for a period of between 15-90 minutes, using the fan speed control buttons (4), in 15 minute increments. After the set period elapses the system will resume to the previously set speed.

  3. NIGHT MODE
    Turns off all LED lights to improve sleeping conditions (except night mode LED which is dimmed).

  4. FAN SPEED
    Allows precise control of fan speed, levels 1 through 20, and increases time increments (express clean).

  5. LED DISPLAY
    This functions as the main display for the system numerically, showing: speed, filter life and Express Clean status.

  6. FAN SPEED INDICATOR
    LED bar increases with fan speed as a visual indicator of speed in addition to the numeric display.

Monitoring filter replacement

FILTER NAME FACTORY DEFAULT SETTING
Filter 1 – Wrap-around Pre-Filter 6 months
Filter 2 – H13 HEPA Filter 36 months
Filter 3 – Not used in V series systems N/A
  1. FILTER CHECK
    Press “Filter Check” button once and filters FILTER 1, FILTER 2 or FILTER 3 illuminate (illustration shows HEPA as example only) in sequence and display the remaining life of each filter. Filter life is displayed in months based on the current fan speed.

  2. STANDARD FILTER RESET
    When the filter light illuminates (illustration shows HEPA as example only) for the filter you are wanting to replace, press and continuously hold “Filter Check” for 5 seconds, the display screen will start to flash. When the flashing stops, filter life has been reset to factory default above.

  3. CUSTOMISING FILTER REPLACEMENT INTERVALS
    To increase or decrease filter life to a custom setting, press
    “Filter Check” button once to select the filter life to customise (illustration shows HEPA as example only). number of months are displayed, continue to hold down “Filter Check” button, the display will flash again for 5 seconds to indicate the new setting has been saved as your preferred (To revert to factory defaults see item 2 procedure above)

  4. CUSTOM FAN SPEED FOR NIGHT MODE
    Default night mode is set to speed 5, to set a custom fan speed for “Night Mode,” use the arrows to adjust the fan to the desired number. Then hold the “Night Mode” button for at least 5 seconds. When released the display will show “I II I” to confirm the new set speed.

System operation

Speed   Control
The system has a variable speed controller and uses an energy efficient European AC fan. Power consumption is relative to the selected speed.

Min 2 4 6 8 10 12 14 16 18 20
6 8 10 14 20 29 40 48 68 82 84
100 155 210 265 320 375 430 485 540 595 650

The higher the speed, the more times per hour the air in your living space will be cleaned, so it is recommended to run the system at the highest speed you are comfortable with. Higher fan speeds will generate higher sound levels .INOVAAIR-AirClean-DV20-Air-Purifier-7

Getting the most out of your AirClean system

Operate the system 24/7.
As contaminants are always present in the air, for maximum effectiveness you should operate the system continuously. By switching the system off you are only allowing these contaminants to build up in the interim until it is switched back on. InovaAir systems are designed for optimal energy efficiency.

Enclose the area where you are operating the system.
Closing doors will allow the system will be much more effective as it will only be filtering air in the one room.

Operate at the highest speed practical
All InovaAir systems include variable speed controls and the speed should be varied depending on the room size, the level of air pollutants present, and the specific application. The higher the operating speed the more effective the system will be in reducing contaminants in the air.INOVAAIR-AirClean-
DV20-Air-Purifier-8

Accessing the filters

INOVAAIR-AirClean-DV20-Air-Purifier-8

  1. Disconnect the power cord.
  2.  Ensure system is sitting on a flat and even surface.
  3.  Pull top of the latches (A) away from the main unit.
  4. Push the latches back towards the main unit (B)
  5. Ensure the latch clasps are clear of catches on the base (C).
  6. Lift casing clear of base to access filters.

Recommended filter replacement intervals

FILTER NAME **APPROXIMATE REPLACEMENT INTERVAL***
Pre-Filter (Wrap-around) 3-6 months (continuous use)
H13 HEPA Filter 3 years (continuous use)

Filter life will vary based on levels of dust present and system proximity to major pollution sources each of which may lower any of the filter lifespans. InovaAir does not warranty consumable filter life.

When to replace the filters

INOVAAIR-AirClean-DV20-Air-Purifier-9

  • Stage 1: Pre-filter
    The pre-filter is the initial stage of filtration, filtering large dust particles right down to ultra-fine sub-micron particles as well as viruses and bacteria. It is made from a patented material used in respirators and face masks.
    Dust levels in the ambient air will affect how long the pre-filter will last. Pre-filters are white and will turn grey within 1-2 weeks of use, this is nothing to be concerned about and simply means the filter is doing its job. In clinical settings, depending on the application and level of exposure to contaminants, the pre-filter should be replaced every 1-3 months.

  • Stage 2: Medical-grade HEPA filter
    The H13 HEPA filter is designed to last 3 years under normal use. As with other filters, the environment in which it is used will determine the filter life. The outside of the HEPA filter will change colour and turn dark grey when it needs replacing. Generally for the first two years of use, the filter will remain white and then gradually get darker in the final months of its life. Please note, the inside of the HEPA filter will always remain white so it is important to check the outside of the filter which is visible when the pre-filter is being changed.

When changing filters
Turn off and unplug the system before unlatching system housing.
To reduce the risk of infection please follow your organization’s personal protective equipment (PPE) guidelines. This may include protective clothing, gloves, a mask or a respirator as the used filters may be extremely dirty, dusty or considered a biohazard if there has been any exposure to infection.
Remove filter and place in a large, sealable bag. Seal the bag closed. Discard the bagged filter in an outdoor waste container or contaminated waste receptacle if available.
Important: Do not attempt to vacuum the HEPA or Pre-filter as this will damage the fine filter fibers and reduce efficiency.
Air intake vents on the sides of the system can be vacuumed with a HEPA grade vacuum, including the base plate which sits under the filters.

Replacing filters

INOVAAIR-AirClean-DV20-Air-Purifier-10

Ordering new filters

Replacement filters can be ordered from the InovaAirTM website using the URL or QR code below. www.inovaairpurifiers.com.au/replacement- filters

INOVAAIR-AirClean-DV20-Air-Purifier-11

Commited to clean air.
InovaAir® is an Australian-owned company that, for more than a decade, has engineered and manufactured air purifiers for home, commercial and industrial use. InovaAir® purifiers are built in a modern factory on the NSW Central Coast, one hour north of Sydney.
InovaAir® has an uncompromising approach to building the world’s best air purifiers with airtight seals that are guaranteed 100% leak-free. The company is committed to using Australian-made components wherever possible. If components must be sourced from overseas, they are always the best available.
Over the years, InovaAir® has developed a reputation for the quality and performance of its unique range of air purifiers. InovaAir® purifiers are built to operate for decades, to be easy to service, to have filters that are easy to replace, to work quietly, effectively and efficiently and to dramatically improve the lives of those who use them.
InovaAir® has a strong commitment to research and development, and continuous improvement is the hallmark of its products. InovaAir’s scientifically proven air cleaning technologies work and their performance can be certified with a laser particle counter.INOVAAIR-AirClean-DV20-Air-
Purifier-12

System warranty

Definitions
In this warranty:
“ACL” refers to the Australian Consumer Law . “Back to Base” means where delivery to and collection of your product from the Service Agent is your responsibility.
“Consumable” includes (without limitation) filters and pre-filters. “InovaAir® Australia” means InovaAir® Australia Pty Ltd ACN 103 549 435. “Factory Second” means a Product sold by InovaAir® Australia or any other authorised person as a ‘second’ meaning a product with a small imperfection that does not impede functioning. “Genuine” means manufactured by or on behalf of InovaAir® Australia. “Product” means a Genuine Product supplied new by InovaAir® Australia. “Purchase Date” means the date of first purchase from InovaAir® Australia or any other authorized person seller or distributor. “Any other authorized person” means a dealer, reseller or retailer of the Product.
“Service Agent” means an authorized InovaAir® Australia service agent. “You” means the End User and “your” has a corresponding meaning.

Introduction

Subject to these conditions, InovaAir® Australia Pty Ltd offers this Warranty on a Product

  1. This Warranty applies in addition to the conditions and warranties implied by the Act in relation to a Product.

  2.  Any other authorized person who has sold a Product to you has acted as principal and has no authority to give any additional warranty or guarantee in relation to the Product on behalf of InovaAir® Australia.

  3. InovaAir® Australia will not be liable for any consequential loss, indirect or special damage arising from your use of the Product. In particular (but without limitation) InovaAir® Australia excludes any liability for actual or expected revenue loss or other loss.
    NB. This exclusion is subject to any relevant Commonwealth or state law, which is intended to override such exclusions.

  4.  In no event shall InovaAir® Australia, its agents, employees, or distributors be liable for special, incidental, consequential, or indirect damages.

  5. The provisions of this warranty supersede and are in lieu of any other
    warranty, whether express or implied, written or oral, including any warranty of merchantability or fitness for a particular purpose.
    NB. This exclusion is subject to any relevant Commonwealth or state law, which is intended to override such exclusions.

  6.  Maximum liability shall not exceed the actual purchase price paid for this product.

  7. This warranty is non-transferable.

  8. Should any of the conditions of the warranty be deemed unenforceable then same shall be severable from the balance of warranty conditions, which shall remain legally binding.

5 Year warranty

InovaAir® Australia warrants that your Product will be free from defects in materials or workmanship for five (5) year/s from your Purchase Date. One (1) year in commercial applications).
At its discretion, InovaAir® Australia will repair or replace your Product, if it is found be defective. InovaAir® Australia will, if it deems the unit defective, either repair or replace the unit at its sole option (and, based on availability, may elect to replace the unit with an air purifier of similar function or value).
To make a Warranty claim, you must:

  • First call InovaAir® Australia’s Contact Centre on 1 300 137 244;
  • Return the Product (if warranty service is required) in its original packaging (or suitable alternative) to a Service Agent, as discussed with the Contact Centre; and
  • Provide a copy of your purchase receipt, to show that this Warranty applies to your Product at the date of your claim.

You are responsible for the cost of and risk in delivery of your Product to and its collection from the Service Agent.

Warranty application

This Warranty applies only:

  • To a Product that is supplied new to You by InovaAir® Australia or by any other authorized person;
  • If you use the Product for your own private or business purposes; and
  • You have not bought the Product for resale.
Warranty exclusions

This Warranty will not apply if during the warranty period:

  •  A Product’s serial number or any rating label is removed or changed in any way; This warranty shall immediately become void if the unit’s serial number label is removed, altered, or is no longer clearly legible;
  • A Product is repaired other than by a Service Agent;
  • You use a Product contrary to any technical or operating environment or safety guidelines recommended in its user guide or manual;
  • No fault found service calls where the perceived problem is explained within the Operating Manual or the trouble shooting section of the operating manual.
  •  This Warranty does not cover costs associated with delivery, handling, freighting or damage to product in transit.
  • This Warranty does not apply to a Product’s malfunction or failure resulting from:
    • Deliberate or accidental damage;
    • Rust or damage to paintwork, varnishes or seals caused by a corrosive atmosphere;
    •  Vermin infestation;
    •  Any modification by the purchaser which affects the reliability or performance of the unit, not attributable to faulty manufacture, parts and labour;
    • Where a unit is installed incorrectly by the purchaser or its servants agents employees or by unqualified persons;
    • Failure is due to improper installation or faulty installation;
    • Failure is due to improper maintenance by customer (refer to maintenance section of Operating Instructions);
    • Misuse, abuse or neglect;
    • Incorrect voltage or a power surge; or
    • Your use of any non-genuine Consumables parts accessories or interfacing;
    • Failure to remove or replace out of date or non-functioning filter.
  •  This warranty covers only manufacturing defects, and not normal wear and tear, including filters which are considered consumables.
  •  InovaAir® does not warrant the Product as a health safety device. The product is not a Medical Device or Therapeutic Device as defined by the Therapeutic Goods Act 1989.
  • All exclusions as determined by InovaAir® Australia at its sole discretion.
  • Filter life: InovaAir® does not warrant the useful life of filter consumables. The filter consumables working life will depend entirely on the environments in which it is used. In dusty environments filter life will be reduced. The Products and their filters are not intended to be used for dust extraction in industrial or commercial applications.

Non-genuine items
InovaAir® Australia advises that if you use non-Genuine Consumables, replacement parts or accessories, you may damage your Product and may void your warranty.

Australian Consumer Law
In addition to your rights under the InovaAir® guarantee, we also provide the following statement as required by the Australian Consumer Law: In Australia, your InovaAir® appliance comes with statutory guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have your InovaAir® appliance repaired or replaced if it fails to be of acceptable quality and the failure does not amount to a major failure.
InovaAir Australia Pty Ltd Unit 8, 1 Reliance Drive, Tuggerah, NSW 2259 Australia
TEL: 1300 137 244
www.airclean.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals