datavideo CM-10 Professional Ceiling Mount for Robotic Pan Tilt Head Instruction Manual

datavideo CM-10 Professional Ceiling Mount for Robotic Pan Tilt Head

Product Information

CM-10 Warranty The CM-10 comes with a standard warranty against manufacturing defects for one year from the date of purchase. Non-Datavideo manufactured products have a one-year warranty period from the date of purchase. Damage caused by accident, misuse, unauthorized repairs, sand, grit, or water is not covered under warranty. Viruses and malware infections on computer systems are also not covered under warranty. The product warranty period begins on the purchase date. All accessories including headphones, cables, batteries, metal parts, housing, cable reel, and consumable parts are not covered under warranty. A three-year warranty extension is available for all Datavideo products purchased after July 1st,
2017, if registered with Datavideo within 30 days of purchase.

Disposal Please dispose of the CM-10 in accordance with local regulations.

Product Introduction

The CM-10 is a ceiling mount designed for PTR robotic pan tilt head. It secures your PTR robotic pan tilt head to the ceiling.

Product Parts Assembly and Installation

Before assembly and installation, please ensure that you have all the parts listed below:

To assemble and install your CM-10, follow these steps:

1. Attach the Ceiling Mount Bracket A to the ceiling using the Expansion Bolts. Use a bubble level meter to ensure that the bracket is level.
2. Attach the Ceiling Mount Bracket B to the Camera Mount Arm using the M3 x 6mm Screws.
3. Attach the Camera Mount Arm to the Ceiling Mount Bracket A using the M3 x 6mm Screws.
4. Secure your PTR robotic pan tilt head to the Camera Mount Arm.

Disclaimer of Product & Services
The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information. Datavideo Technologies always recommend that you double check the information in this document for accuracy before making any purchase decision or using the product. Datavideo Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the information contained within this manual. Further advice on the content of this manual or on the product can be obtained by contacting your local Datavideo Office or dealer.

Warranty

Standard Warranty

• Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of purchase.
• The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty.
• The product warranty period beings on the purchase date. If the purchase date is unknown, the product warranty period begins on the thirtieth day after shipment from a Datavideo office.
• All non-Datavideo manufactured products (product without Datavideo logo) have only one year warranty from the date of purchase.
• Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered under warranty.
• Viruses and malware infections on the computer systems are not covered under warranty.
• Any errors that are caused by unauthorized third-party software installations, which are not required by our computer systems, are not covered under warranty.
• All mail or transportation costs including insurance are at the expense of the owner.
• All other claims of any nature are not covered.
• All accessories including headphones, cables, batteries, metal parts, housing, cable reel and consumable parts are not covered under warranty.
• Warranty only valid in the country or region of purchase.
• Your statutory rights are not affected.

Three Year Warranty

• All Datavideo products purchased after July 1st, 2017 qualify for a free two years extension to the standard warranty, providing the product is registered with Datavideo within 30 days of purchase.
• Certain parts with limited lifetime expectancy such as LCD panels, DVD drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting, Non-PCIe Card and third party provided PC components are covered for 1 year.
• The three-year warranty must be registered on Datavideo’s official website or with your local Datavideo office or one of its authorized distributors within 30 days of purchase.

Disposal

For EU Customers only – WEEE Marking
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

CE Marking is the symbol as shown on the left of this page. The letters “CE” are the abbreviation of French phrase “Conformité Européene” which literally means “European Conformity”. The term initially used was “EC Mark” and it was officially replaced by “CE Marking” in the Directive 93/68/EEC in 1993. “CE Marking” is now used in all EU official documents.

Introduction

CM-10 is a ceiling mount designed for PTR robotic pan tilt head, securing your PTR robotic pan tilt head to the ceiling.

Parts Assembly and Installation

In this section, you will be shown how you can assemble and install your CM-10.

Pre-work

First check you have all the parts listed in the table below.
Note: There is a bubble level meter on the ceiling bracket A.

Procedure

Follow the steps outlined below to assemble the ceiling and camera mounts and secure them to your PTR robotic pan tilt head.

1. Secure the ceiling mount bracket B to the ceiling. The dimensions diagram of the ceiling mount bracket B is shown below.
   If your ceiling is made of concrete, then on the surface where the PTR robotic pan tilt head is to be installed, drill six holes spaced according to the dimensions indicated in the diagram above (enclosed by six rectangles) then use the six expansion bolts in your product package to secure the ceiling mount bracket B to the ceiling.
   If your ceiling is made of wood, then on the surface where the PTR robotic pan tilt head is to be installed, drill four holes spaced according to the dimensions indicated in the diagram above (see the arc shaped holes enclosed in a circle) then use four self-tapping screws to secure the ceiling mount bracket B to the ceiling. Please note that self-tapping screws are not provided in the product package.

2. Remove the screws as depicted in the diagram below to unload the camera mount of the PTR robotic pan tilt head.

3. Re-assemble the camera mount

4. Secure the camera mount to the PTR robotic pan tilt head.

5. Secure the ceiling mount bracket A to the base of the PTR robotic pan tilt head.

6. As shown in the diagram, push the ceiling mount bracket A along with the PTR robotic pan tilt head into the ceiling mount bracket B secured to the ceiling then backwards until the two brackets click into place.

7. Insert the four M4 x 8mm screws (black) into each of the four holes in the four corners of the ceiling mount bracket A then tighten.

8. Finally secure your camera to the camera mount base as shown in the diagram below.

Frequently Asked Questions

This section describes problems that you may encounter while using CM-10. See related items for suggested solutions. If problem still exists, please contact your distributor or the service center.

the PTR robotic pan tilt head is not aligned**

after installation.

| You can insert some soft pads into the space between the ceiling mount bracket B and the ceiling to align the PTR robotic

pan tilt head horizontally.

Dimensions and Weight

Ceiling Mount
Unit: mm

Weight: 1.66 kg (3.66 lb)

Camera Mount Arm
Unit: mm

Weight: 0.35 kg (0.7716 lb)

Specifications

Tilt Head

Weight| Ceiling Mount: 1.66 kg (3.66 lb)

Camera Mount Arm: 0.35 kg (0.7716 lb)

Dimensions| Ceiling Mount: 208 x 221 x 35 (mm)

Camera Mount Arm: 7 x 141 x 226 (mm)

Max. Load Weight| 10 kg

Service & Support

It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo.com for answers to  common questions, support requests or contact your local office below.
Please visit our website for latest manual update.
https://www.datavideo.com/product/CM-10

All the trademarks are the properties of their respective owners. Datavideo Technologies Co., Ltd. All rights reserved 2020

References

• CM-10 Celling Mount | Datavideo | Datavideo | Professional end-to-end solutions provider for your live video production.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>