datavideo ZEK-2 01 Zoom Control Kit Instruction Manual
- June 4, 2024
- Datavideo
Table of Contents
ZOOM CONTROL KIT
FOR TILTA NUCLEUS-M
MOTOR
ZEK-2
Instruction Manual
may not be correct or may be incomplete. This manual may contain typing
errors, omissions, or incorrect information. Datavideo Technologies always
recommend that you double-check the information in this document for accuracy
before making any purchase decision or using the product. Datavideo
Technologies is not responsible for any omissions or errors, or for any
subsequent loss or damage caused by using the information contained within
this manual.
Further advice on the content of this manual or on the product can be obtained
by contacting your local Datavideo Office or dealer.
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Warnings and Precautions
-
Read all of these warnings and save them for later reference.
-
Follow all warnings and instructions marked on this unit.
-
Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
-
Do not use this unit in or near water.
-
Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage.
-
Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure the safe and reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit should not be placed in a built-in installation unless proper ventilation is provided.
-
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company.
-
Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be walked on, rolled over, or otherwise stressed.9.
If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord rating. -
Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15 amperes.
-
Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.
Never spill liquid of any kind onto or into this unit. -
Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous voltage points or other risks, and will void your warranty. Refer all service issues to qualified service personnel.
-
Unplug this product from the wall outlet and refer to qualified service personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When the liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust only those controls that are covered by the operating instructions in this manual; improper adjustment of other controls may result in damage to the unit and may often require extensive work by a qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for service.
Warranty
S tandard Warranty
- Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of purchase.
- The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty.
- The product warranty period beings on the purchase date. If the purchase date is unknown, the product warranty period begins on the thirtieth day after shipment from a Datavideo office.
- All non-Datavideo manufactured products (products without the Datavideo logo) have only one year warranty from the date of purchase.
- Damage caused by accident, misuse, unauthorized repairs, sand, grit, or water is not covered under warranty.
- Viruses and malware infections on computer systems are not covered under warranty.
- Any errors that are caused by unauthorized third-party software installations, which are not required by our computer systems, are not covered under warranty.
- All mail or transportation costs including insurance are at the expense of the owner.
- All other claims of any nature are not covered.
- All accessories including headphones, cables, batteries, metal parts, housing, cable reel, and consumable parts are not covered under warranty.
- Warranty only valid in the country or region of purchase.
- Your statutory rights are not affected.
Three Year Warranty
- All Datavideo products purchased after July 1st, 2017 qualify for a free two years extension to the standard warranty, providing the product is registered with Datavideo within 30 days of purchase.
- Certain parts with limited lifetime expectancy such as LCD panels, DVD drives, Hard drives, Solid State drives, SD Card, USB Thumb drives, Lighting, Non-PCIe Card, and third-party-provided PC components are covered for 1 year.
- The three-year warranty must be registered on Datavideo’s official website or with your local Datavideo office or one of its authorized distributors within 30 days of purchase.
Disposal
For EU Customers only – WEEE Marking This symbol on the product or on its
packaging indicates that this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate
collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more information about
where you can drop off your waste equipment for recycling, please contact your
local city office, your household waste disposal service, or the shop where
you purchased the product.
CE Marking is the symbol as shown on the left of this page. The letters
“CE” are the abbreviation of the French phrase “Conformité Européene” which
literally means “European Conformity”. The term initially used was “EC Mark”
and it was officially replaced by “CE Marking” in Directive 93/68/EEC in 1993.
“CE Marking” is now used in all EU official documents.
Introduction
ZEK-2 Zoom Encoder Kit is a mechanical device that allows you to mount the
Tilta Nucleus-M motor which adds automatic zoom positioning to the Panasonic
Lumix BGH-1 camcorder mounted on the PTR-10/10T MARK II Robotic Pan Tilt Head.
Please note that you can purchase the Tilta Nucleus-M motor from the Tilta
official website https://tilta.com/shop/nucleusm-motor-kit-i/).
Features
- Automatic zoom positioning
- Flexible mount positions
Assembly
There are two sections in this chapter. We will describe different parts of
the ZEK-2 in the first section and the assembly procedure will be outlined in
the second section.
Product Parts
The table below lists all the parts that you will find in the product package.
| Name | Descriptions |
|---|---|
| Tilta Nucleus-M Motor | The Tilta Nucleus-M motor should engage
with the gear ring belt wrapped around the camcorder’s zoom ring. The two Ext.
ports should be connected to the PTR-10/10T MARK II Robotic Pan Tilt Head’s DC
OUT and Zoom Sensor ports.
Note: The Tilta Nucleus-M motor is not
provided as part of the ZEK-2. To purchase, please follow the link below:
https://tilta.com/shop/nucleus-m-motorkit-i/
D-Tap PowerBreakout
Cable| Connect the D-Tap end of the D-Tap power breakout cable to the DC OUT
port of the PTR-10/10T MARK II. On the breakout end, the Tilta 7pin connector
should be connected to the Tilta Nucleus-M motor and the DC jack should be
connected to the power socket on the Panasonic Lumix DCBGH-1 camera.
Tilta ControlCable| Use the Tilta control cable to connect the zoom sensor
port of the PTR-10/10T MARK II Robotic Pan Tilt Head to one of the Ext.
ports of the Tilta Nucleus-M motor. 
Metal Bar| The metal bar holds the Tilta Nucleus-M motor in place. 
Bar Holder| Insert the metal bar into the bar holder then mount it to the
camera mount plate of the PTR-10/10T Mark II with the three
screws provided in the product package. 
M0.8 Gear Ring Belt| Wrap the gear ring belt around the Panasonic Lumix DC- BGH-1 camera’s zoom ring then push the Tilta Nucleus-M motor
towards the belt until they engage.
Note: The M0.8 gear ring belt is a
general-purpose part.
To find a better fit for a specific application, please follow the link below:
https://tilta.com/shop/seamless-focusgear-ring/
Instructions
-
Step 1
As shown in the diagram below, insert one end of the metal bar into the bar holder and another end of the metal bar into the Tilta Nucleus-M motor then tighten.
-
Step 2
Use the three screws provided in the plastic zipper bag to secure the bar holder along with the metal bar and the Tilta Nucleus-M motor to the camera mount plate of the PTR-10/10T MARK II as shown in the diagram below.
-
Step 3
Wrap the gear ring belt around the Panasonic Lumix DC-BGH-1 camera’s zoom ring then push the Tilta Nucleus-M motor towards the belt until they engage.
-
Step 4
Connect the three cables listed below for operation and power supply.
D-Tap Power Breakout Cable
Connect the D-Tap end of the D-Tap power breakout cable to the DC OUT port of
the PTR-10/10T MARK II. On the breakout end, the Tilta 7-pin connector should
be connected to one Ext. the port on the Tilta Nucleus-M motor, and the DC
jack should be connected to the power socket on the Panasonic Lumix DCBGH-1
camera.
Tilta Control Cable
The Tilta control cable should connect between the Zoom Sensor port of the
PTR-10/10T MARK II and one Ext. the port on the Tilta Nucleus-M motor.
Remote Cable
The remote cable is a standard cable shipped with the PTR10/10T MARK II
Robotic Pan Tilt Head. The remote cable can be used to connect the Remote port
of the PTR-10/10T MARK II to the REMOTE terminal of the Panasonic Lumix DC-
BGH-1 camera. The 8pin snap-and-lock mini-din connector of the remote cable
will be securely fastened once plugged into the Remote port. To remove, use
two fingers to gently hold the part of the plug labeled by two arrows then
pull the connector outward.
The diagram below illustrates the wire connections from the side panel of the PTR-10/10T MARK II to the Panasonic Lumix DC-BGH-1 camera and the Tilta Nucleus-M motor.
- Step 5
In this step, we will show you how to configure the PTR-10/10T MARK II and the Panasonic Lumix DC-BGH-1 camera.
PTR-10/10T MARK II Settings
-
Toggle the DC Output to 12 V by setting positions 7 and 8 of the DIP switch to ON.
-
On the OSD menu, Set Remote Out Mode to LANC
Panasonic because the Panasonic Lumix DC-BGH-1 camera can be accessed via the LANC interface.
4. Remote Control
→ 6. Set Remote Out
→ 1. Remote Out mode
→ LanC Panasonic -
Set Zoom Encoder Mode to Tilta-CTL.
-
Reboot the device in order for the changes to be effective.
BGH-1 Settings
The camera’s OSD menu settings
-
Set the Focus Mode
Follow the menu path below and set the focus mode to MF to manually adjust the focus.
[MENU/SET] [Focus Mode]
-
Set the Exposure Mode (IRIS)
Follow the menu path below and set the exposure mode to A or M mode.
[MENU/SET] [Exposure Mode] A mode is the aperture priority mode allowing you to set the aperture manually while the camera automatically selects a shutter speed.
M mode allows you to set the aperture and shutter speed manually.
Note: If you find that focus or iris cannot be adjusted, try power cycling the BGH-1 and PTR-10 MARK II.
-
Step 6
Push the lens of the Panasonic Lumix DC-BGH-1 camera to the AUTO mode so that lens movement is dependent on the camera’s OSD menu settings.
Note: Do not push the lens to the Full Manual mode. -
Step 7
On the remote control of the PTR-10/10T MARK II, press the Home button (enclosed in the red rectangle) as depicted in the diagram below to start calibrating the Tilta Nucleus-M motor.
Calibration is complete after the motor makes one full rotation and then returns to its original position. You can start adjusting the camera zoom after the motor is calibrated.
Notes ……………..
Specifications
| Name | Zoom Encoder Kit |
|---|---|
| Model No. | ZEK-2 |
| Zoom | Automatic zoom positioning |
| Mount | Flexible mount positions |
Accessory List
| No | Item | Qty |
|---|---|---|
| 1 | Tilta control cable (mini-Din 4 Pin to Tilta 7 pin) | 1 |
| 2 | D-tap power breakout cable (D-tap to Tilta 7 pin and DC 5.5mm) | 1 |
| 3 | Gear Ring M0.8 | 1 |
| 4 | Metal Bar | 1 |
| 5 | Bar Holder | 1 |
| 6 | Gear Screw M3 x 4 mm | 3 |
Service & Support
It is our goal to make your product ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our website www.datavideo.com for answers to common questions, and support requests, or contact your local office below.
Please visit our website for the latest manual update.
www.datavideo.com/product/ZEK-2
| @DatavideoUSA
@DatavideoEMEA
@DatavideoTaiwan
@DatavideoAsia| @Datavideolndia201 6
@Datavideojapan
@DatavideoLatam
@DatavideoBrasil
---|---|---
| @DatavideoUSA
@DVDAIDVC
---|---
| @Datavideo
@Datavideo EMEA
@Datavideo Taiwan
---|---
| @DatavideoUSA
@DatavideoEurope
All the trademarks are the properties of their respective owners.
Datavideo Technologies Co., Ltd. All rights reserved 2020
G082067864E1 Jan-07.2022
Ver: El
References
- ZEK-2 Zoom Control Kit for Tilta Nucleus-M Motor | Datavideo | Datavideo | Professional end-to-end solutions provider for your live video production.
- Nucleus-M: Wireless Lens Control System | Tilta
- Nucleus-M Motor Kit I | Tilta
- Nucleus-M Motor Kit I | Tilta
- Seamless Focus Gear Ring | Tilta
- Seamless Focus Gear Ring | Tilta
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>