datavideo HBT-12 HDBaseT Receiver Box Instruction Manual

: June 5, 2024
: Datavideo

Table of Contents

Introduction
System Diagram
Connections
RS-232/RS-422 Pinout
Dimensions
Specifications
FCC Compliance Statement
Warranty
Service & Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

datavideo HBT-12 HDBaseT Receiver Box Instruction Manual

Introduction

The HBT-12 is an HDBaseT receiver designed to interface between transmitting and receiving devices. The receiver accepts up to 4K image quality video.

With the 56V power connected to one end of the HBT-12 HDBaseT receiver, the HBT-12 will thus be able to power the transmitting device by PoE plus technology (PoE++). Please only use Cat 7 Ethernet cables to connect PoE++ powered devices.

HDBaseT connection between the transmitter and the receiver can be established using a single Ethernet cable. In other words, HDMI video, DVIP control commands and power (PoE++) can be transmitted between the transmitter and the receiver over just one cable.

Features

Receives up to 4Kx2K video from the transmitter.
Extends video transmission to 120m (maximum).
Transmits video, audio, DVIP control, RS-422/232 control and PoE+ over a single Cat 7 cable.
56V PoE+ Power supply.
DVIP Control Protocol
RS-422/232 Control Protocol

System Diagram

Connections

Rear Panel

HDMI OUT
HDMI port for video output to devices such as switchers, recorders or monitors.

DVIP Port
The DVIP port can be connected to an Ethernet switch or router, serving as a communication port between the network and the HBT-12 receiver.

56V DC IN
56V DC power input connection
Power LED Indicator
ON: Power connected
OFF: Power disconnected

Front Panel

HDBaseT Port
Only use a Cat 7 Ethernet cable to connect between the PTR-10T MARK II robotic pan tilt head and the HBT-12 receiver.

Note: See Cable Selection for cable recommendations.

RS-232/RS-422 Port (RJ-45)
The RS-232/RS-422 port connects HBT-12 directly to Datavideo camera controllers such as RMC-180, RMC-300A or RMC-300C. Use the RS232 or RS-422 custom cable to connect. See RS232/RS-422 pinout for more information about the respective cabling.

DIP Switch
The receiver box allows long distance connectivity to PTR-10T MARK II of up to 120 meters while compromising on maximum supported resolution of up to 1080p. Select 4K mode (2160p) if the connection distance is less than 70 meters. If your system is not required to support resolutions higher than 1080p, you can activate long reach mode and enjoy longer cable reach of up to 120 meters.

The DIP Switch is used to select from the available connection modes listed as follows:

00: 4K Mode RS-232
01: 4K Mode RS-422
10: Long Reach RS-232
11: Long Reach RS-422

Note: See the Cable Selection section for cable recommendations.

RS-232/RS-422 Pinout

You can use RS-232 or RS-422 control protocol to control the PTR-10T MARK II behind the HBT-12 HDBaseT Receiver Box with Datavideo camera controllers such as RMC-180, RMC-300A or RMC-300C. You will need to use a custom Ethernet cable to connect between the controller
and HBT-12. Wire the connection cable according to the respective RS232 and RS-422 wiring diagrams shown below.

RS-232

RS-232 Pinout

RS-422

RS-422 Pinout

Dimensions

All measurements in millimeters (mm)

Specifications

HBT-12 HDBaseT Receiver Box

Video / Audio
Input| HDBaseT RJ-45 x 1
Output| HDMI x 1
Control
DVIP Ethernet| RJ-45 x 1
RS-422 / RS-232| RJ-45 x 1
Power
DC IN| DC 56 V
PoE Standard| IEEE 802.3bt
Dimensions
L x W x H| 131.8 x 85 x 45.2 mm
Physical and Operating Environments
Weight| 0.4 kg
Operating Temperature| 0 – 40 °C
Operating Relative Humidity| 10% – 80% (non condensing)
Storage Temperature| -10 – 60 °C
Storage Relative Humidity| 5% – 80% (non condensing)
HDBaseT Transmission Distance| 1080p@60 Up to 120M by Cat 7 Cable; 4K2K@30 Up to 70M by Cat 7 Cable

Cable Selection

The table below summarizes the recommended Cat 7 cable.

Cable	Range	Video Resolution
Cat 7	120 meters	Ultra HD video formats:

HDMI Deep color: 1080p, 60, 48 bpp.
4K x 2K
Data rates higher than 5.3 Gbps or above 255 MHz TMDS clock.
Recommended Cables for Ultra-HD Video at 120 meter range
Type| P/N| Manufacturer| Website
CAT7

S/FTP

Disclaimer of Product & Services

The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information. Datavideo Technologies always recommend that you double check the information in this document for accuracy before making any purchase decision or using the product. Datavideo Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the information contained within this manual.
Further advice on the content of this manual or on the product can be obtained by contacting your local Datavideo Office or dealer.

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Warnings and Precautions

Read all of these warnings and save them for later reference.
Follow all warnings and instructions marked on this unit.
Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use this unit in or near water.
Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage.
Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit should not be placed in a built-in installation unless proper ventilation is provided.
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company.
Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be walked on, rolled over, or otherwise stressed.
If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord rating.
Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15 amperes.
Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock.
Never spill liquid of any kind onto or into this unit.
Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous voltage points or other risks, and will void your warranty. Refer all service issues to qualified service personnel.
Unplug this product from the wall outlet and refer to qualified service personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust only those controls that are covered by the operating instructions in this manual; improper adjustment of other controls may result in damage to the unit and may often require extensive work by a qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for service.

Warranty

Standard Warranty

Datavideo equipment are guaranteed against any manufacturing defects for one year from the date of purchase.
The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty.
The product warranty period begins on the purchase date. If the purchase date is unknown, the product warranty period begins on the thirtieth day after shipment from a Datavideo office.
All non-Datavideo manufactured products (product without Datavideo logo) have only one year warranty from the date of purchase.
Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered under warranty.
Viruses and malware infections on the computer systems are not covered under warranty.
Any errors that are caused by unauthorized third-party software installations, which are not required by our computer systems, are not covered under warranty.
All mail or transportation costs including insurance are at the expense of the owner.
All other claims of any nature are not covered.
All accessories including headphones, cables, and batteries are not covered under warranty.
Warranty only valid in the country or region of purchase.
Your statutory rights are not affected.

Three Year Warranty

All Datavideo products purchased after July 1st, 2017 are qualified for a free two years extension to the standard warranty, providing the product is registered with Datavideo within 30 days of purchase.
Certain parts with limited lifetime expectancy such as LCD panels, DVD drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting, Camera module, PCIe Card are covered for 1 year.
The three-year warranty must be registered on Datavideo’s official website or with your local Datavideo office or one of its authorized distributors within 30 days of purchase.

Disposal

For EU Customers only – WEEE Marking
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

CE Marking is the symbol as shown on the left of this page. The letters “CE” are the abbreviation of French phrase “Conformité Européene” which literally means “European Conformity”. The term initially used was “EC Mark” and it was officially replaced by “CE Marking” in the Directive 93/68/EEC in 1993. “CE Marking” is now used in all EU official documents.

Service & Support

It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo.com for answers to common questions, support requests or contact your local office below.

Please visit our website for latest manual update.
http://www.datavideo.com/product/HBT-12

Service & Support