SAB H1653-K 3 Blades Rotor Tail Instruction Manual
- October 30, 2023
- SAB
Table of Contents
SAB H1653-K 3 Blades Rotor Tail
Product Information: 3-Blades Rotor Tail Kit [H1653-K]
The 3-Blades Rotor Tail Kit is designed to convert the 2-blade rotor of the RAW 700 and KRAKEN 700 into a 3-blade rotor. It comes with various parts including Tail Pitch Slider Assembly, Tail Blade Grip Assembly, Tail Pulley Assembly, and Tail Rotor System Assembly. The kit also includes spare parts such as Tail Hub, Tail Shaft, Pin M2, and Tail Blade Grip.
Parts Included
- Tail Pitch Slider Assembly
- Tail Blade Grip Assembly (x3)
- Tail Pulley Assembly
- Tail Rotor System Assembly
Spare Parts
- Tail Hub [H0418-S]
- Tail Shaft [H0419-S]
- Pin M2 [H0435-S]
- Tail Blade Grip [H1033-S]
Recommended Tail Blades
- SAB blades for 3 blades tail rotor 105 mm
- SAB blades for 3 blades tail rotor 115 mm
Recommendations
- These parts should be used only with models SAB.
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapter 2, Important notes.
- Use Loctite on all threads.
- Prior to use, lubricate all movements with spray lubricant.
Product Usage Instructions
- Read the user manual carefully before starting the assembly of the kit.
- Refer to the website www.goblin-helicopter.com for updates and other important information.
- Use Loctite on all threads during assembly.
- Lubricate all movements with spray lubricant prior to use.
- After the use of Loctite, check the proper sliding off all command.
- It is normal for the tail to feel a bit tight after initial assembly. After 2-5 flights allowing the system to become smooth.
- The set screw should align with the hole in the tail shaft.
This KIT is designed to convert the 2-blade rotor of the RAW 700 and KRAKEN 700 into a 3-blade rotor. Please read this user manual carefully, it contains instructions for the correct assembly of the KIT. Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You..
Tail Pitch Slider Assembly
Tail Blade Grip Assembly …..x3
Tail System Assembly
NOTE:
After the use of Loctite, need to the check the proper sliding off all command
NOTE:
It is a normal for the tail to feel a bit tight after initial assembly. After
2-5 flights allowing the system to become smooth.
Tail Pulley Assembly
RECOMMENDATIONS
- These parts should be used only with models SAB.
- Please follow all the instructions shouwn in the Goblin main manual. In this manual please read Chapter 2, Important notes.
- Use Loctite on all threads.
- Prior to use, lubricate all movements with sprat lubricant.
- Possible to use with the follow Tail blades:
- SAB blades for 3 blades tail rotor 105 mm
- SAB blades for 3 blades tail rotor 115 mm
SPARE PARTS
Tail Hub [H0418-S]
- 1 x Tail Hub.
- 1 x Set Screw M4x6mm.
- 3 x Socket Head Cap Screws M3x8mm.
- 3 x Washer Ø3xØ7x1mm.
- 3 x Washer Ø5xØ7×0,2mm.
Tail Shaft [H0419-S]
- 1 x Tail Shaft.
- 2 x Set Screws M4x6mm.
Pin M2 [H0435-S]
- 3 x Pin M2.
- 3 x Spacer 2x 3x3mm.
- 3 x Tail Pitch Slider Link.
- 6 x Socket Head Cap Screws M2x6mm.
Tail Blade Grip [H1033-S]
- 2 x Aluminum Tail Blade Grip.
- 4 x Bearing Ø5xØ10x4mm.
- 2 x Thrust bearing Ø5xØ10x4mm.
- 2 x Washer Ø7.5xØ10×0,5mm.
Tail Pulley Z26 [H1098-26-S]
- 1 x Tail Pulley Assembly.
- 1 x Set Screw M4x6mm.
Tail Pitch Slider [H1294-S]
- 1 x Tail Pitch Slider 01.
- 1 x Tail Pitch Slider 02.
- 1 x Tail Pitch Slider 03.
- 1 x Spacer 8x 9×3.2mm.
- 2 x Flanged Bearings 8x 12×3.5mm
This KIT is designed to convert the 2-blade rotor of the RAW 700 and KRAKEN 700 into a 3-blade rotor. Please read this user manual carefully, it contains instructions for the correct assembly of the KIT. Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>