SAB H1630-S Carbon Tail Boom Conversion Kit Owner’s Manual

: October 30, 2023
: SAB

Table of Contents

GOBLIN RAW 420 TECHNICAL SPECIFICATIONS
TAIL GROUP ASSEMBLY
TAIL BOOM ASSEMBLY
TAIL BELT TENSION
INSTALLATION OF THE ESC/FBL
SPARE PARTS
Documents / Resources

CARBON TAIL BOOM CONVERSION KIT
[H1630-S]
Owner’s Manual

Bag 1
This kit is designed to convert the boom of the Raw 420 from a traditional aluminum round boom to a carbon fiber molded style boom.
This conversion kit is designed for use on the SAB Raw 420 [SG421] model only.
Please read this user manual carefully together with the kit manual, both manuals contain instructions for the proper assembly of this product.
Refer to our web site www.goblin-helicopter.com for updates and other important information. Thank you.

GOBLIN RAW 420 TECHNICAL SPECIFICATIONS

TAIL GROUP ASSEMBLY

Bag 4

TAIL BOOM ASSEMBLY

TAIL BOOM ASSEMBLY

TAIL BELT TENSION

To provide the correct tail belt tension, you can use the “zig-zag” method.
Figure 1: Loosen the 2 RED and the BLUE screws and push the tail side plate in he direction of the red arrow, tighten the BLUE screw while pushing.
Figure 2: Loosen the 2 RED and the YELLOW screws and push the tail side plate in the direction of the red arrow, tighten the YELLOW screw while pushing.
You can continue to do this back and forth until the tail belt is tight enough.
We recommend higher tension for hard 3D while you can have less tension for sport flying. When setting the belt tension, tighten all screws making sure the
tail shaft is perpendicular to the boom.
Figure 3: The tail output shaft must be perpendicular to the boom.

TAIL BOOM ASSEMBLY
**** Before installing the plastic links onto the threaded rod, be sure that you have waited for at least 12 hours and glue is fully cured.

INSTALLATION OF THE ESC/FBL

SPARE PARTS

Carbon Boom
[H1629-S]
– 1 x Carbon Boom.
– 1 x M8 Block.
– 2 x Blot M8.
– 2 x Tail Element Block.
– 2 x Double Side Tape.
– 4 x Nylon Nut M2.5.
– 4 x Finishing Washer M2.5.
– 4 x Socket Head Cap Screw M2.5x8mm.|
---|---
FBL Plate
[H1631-S]
– 1 x FBL Plate.
– 2 x Socket Head Cap Screw M2.5x5mm.|
Tail Fin
[H1633-S]
– 1 x Tail Fin.
– 1 x Tail Fin Sticker.
– 1 x Flanged Bearing 5x 13x4mm.|
Carbon Boom Block
[H1635-S]
– 1 x Carbon Boom Block.
– 4 x Socket Head Cap Screw M2.5x8mm.|
Tail Side Plate
[H1632-S]
– 1 x Tail Side Plate.
– 1 x Flanged Bearing Ø 5x Ø 13x4mm.|
Cross Tail Case
[H1634-S]
– 1 x Cross Tail Case.
– 2 x Socket Head Cap Screw M2.5x6mm.|
Carbon Rod Guide
[H1642-S]
– 1 x Carbon Rod Guide.
– 2 x Socket Head Cap Screw M2x6mm.|

SAB HELI DIVISION

Documents / Resources

| SAB H1630-S Carbon Tail Boom Conversion Kit [pdf] Owner's Manual
H1630-S Carbon Tail Boom Conversion Kit, H1630-S, Carbon Tail Boom Conversion Kit, Tail Boom Conversion Kit, Boom Conversion Kit, Conversion Kit
---|---