nVent 708SF Caddy Push Install Rod Wire Hanger Instruction Manual
- October 30, 2023
- nVent
Table of Contents
nVent 708SF Caddy Push Install Rod Wire Hanger
Product Information
The PUSH INSTALL ROD/WIRE HANGER WITH SHOT-FIRE BRACKET, 1/4 ROD is a product manufactured by nVent. Its catalog number is 708SF.The product is made of steel and spring steel finish with electrogalvanized coating. The nVent CADDY Armour Rod Size is 1/4, and the Wire Size is #8. The product has a height of 3 1/16 inches, width of 2 1/4 inches, A of 1.300 inches and can carry a static load of up to 100 lbs.
Features
- Material: Steel;Spring Steel
- Finish: Electrogalvanized
- nVent CADDY Armour Rod Size: 1/4
- Wire Size: #8
- Height: 3 1/16 inches
- Width: 2 1/4 inches
- A: 1.300 inches
- Static Load: 100 lbs
Additional Product Details
The product comes with diagrams for proper installation and usage. It is
important to note that nVent products should only be installed and used
according to the product instruction sheets and training materials provided by
nVent. Improper installation or misuse of the product may cause it to
malfunction, damage property, cause serious bodily injury or death, and/or
void the warranty.
Contact Information
For inquiries or support, you may contact nVent customer service
representatives through the following:
Europe
- Netherlands: +31 800-0200135
- France: +33 800 901 793
- Germany: 800 1890272
- Other Countries: +31 13 5835404
APAC
- Shanghai: + 86 21 2412 1618/19
- Sydney: +61 2 9751 8500
Brand Portfolio
nVent is a company that offers a powerful portfolio of brands, including
CADDY, ERICO, HOFFMAN, RAYCHEM, SCHROFF, and TRACER. All brands are owned by
their respective owners.
Product Usage Instructions
- Make sure to read the product instruction sheet and training materials provided by nVent before installing and using the product.
- Using the diagrams provided, install the PUSH INSTALL ROD/WIRE HANGER WITH SHOT-FIRE BRACKET, 1/4 ROD according to the instructions.
- Use the product to hang and support wires or rods. The product can carry a static load of up to 100 lbs.
- Do not misuse or apply excessive force on the product. This may cause it to malfunction or damage property.
- If you encounter any issues with the product, contact nVent customer service representatives for assistance.
CATALOG NUMBER
708SF
FEATURES
- Prmits pre-assembly of wire or plain rod
- Suspends wire or plain rod from horizontal structures
- Complete with shot-fire bracket and pre-assembled drive pin from DEWALT®
- Quickly and easily attaches to concrete, steel or composite metal decking
- Integrated pin installs easily using powder-actuated or single-shot gas-actuated tools
- ICC-ES ESR-2024 evaluation report available for drive pin from DEWALT®
PRODUCT ATTRIBUTES
- Material: Steel;Spring Steel
- Finish: Electrogalvanized;nVent CADDY Armour
- Rod Size: 1/4″
- Wire Size: #8
- Height: 3 1/16″
- Width: 2 1/4″
- A: 1.300″
- Static Load: 100 lb
ADDITIONAL PRODUCT DETAILS
Uses Powers Fasteners, Inc. part number 50032.
Static load was established based on a 1” (25.4 mm) embedment depth and 3,000
psi (20.68 MPa) lightweight concrete. For variations in embedment and material
please consult anchors.dewalt.com.
Pre-assembled drive pin from Powers Fasteners, Inc. works with Powers® C4CZ,
Simpson® GCN-MEPKT, SPIT® P1000, P200, P2201, P3500 / PA3500, P35s, P45, P60,
P7201, Sniper; Ramset® 721, Cobra, D45 / D60 / D60L, M70, SA270, T3SS, TS750P,
TS60P, Viper; Hilti® DX35, DX350 / DX351 / DX36M, DX100 / DX200, DX460, DXA40,
DXA41, DXE72 / DX400; Würth® Diva-1, BST-1, BST-2 or equivalent nailers.
For shot-fired supports in seismic design category D, E, or F, maximum load is
the lesser of 90 lb (400 N) or the published load.
DIAGRAMS
WARNING
nVent products shall be installed and used only as indicated in nVent’s
product instruction sheets and training materials. Instruction sheets are
available at www.nvent.com and from your nVent
customer service representative. Improper installation, misuse, misapplication
or other failure to completely follow nVent’s instructions and warnings may
cause product malfunction, property damage, serious bodily injury and death
and/or void your warranty.
North America
+1.800.753.9221
Option 1 – Customer Care
Option 2 – Technical Support
Europe
Netherlands:
+31 800-0200135
France:
+33 800 901 793
Europe
Germany:
800 1890272
Other Countries:
+31 13 5835404
APAC
Shanghai:
+ 86 21 2412 1618/19
Sydney:
+61 2 9751 8500
Our powerful portfolio of brands:
nVent.com CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER
© 2022 nVent. All nVent marks and logos are owned or licensed by nVent
Services GmbH or its affiliates. All other trademarks are the property of
their respective owners.
nVent reserves the right to change specifications without notice.
References
- Anchoring and Fastening Systems from DEWALT Anchors & Fasteners
- The Future of Connection and Protection | nVent
- The Future of Connection and Protection | nVent
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>