CONDUCTIX wampfler 08-V015-0493 Conductor Rail System 0813 Instruction Manual
- October 30, 2023
- Conductix Wampfler
Table of Contents
CONDUCTIX wampfler 08-V015-0493 Conductor Rail System 0813
Product Information
The Disassembly Tool Program 0813 is a set of two tools that aid in the removal of a hanger clamp from the conductor rail. The tool is designed to be used by specialized technicians only and requires the use of personal protective equipment. The tool should only be used under appropriate operating conditions, and falling conductor rail system components may cause injury due to crushing of skin and limbs if not installed properly. Further installation instructions can be found in the operating instructions BAL0813-0007.
Product Usage Instructions
- Slide Tool 1 up to the stopper between the conductor rail and hanger clamp.
- Press the conductor rail against Tool 1 or against the hanger clamp, respectively.
- Insert Tool 2 on the open side of the conductor rail. The retaining clamp of the hanger clamp bends up.
- Pull out the conductor rail.
- Remove Tool 2 from the open side of the conductor rail.
- In order to remove Tool 1, the tension spring of the retaining clamp may need to be pushed away.
Note: Refer to Fig. 1-9 in the user manual for a visual representation of the steps mentioned above.
Risk of injury
Risk of injury due to crushing of skin and limbs!
There is a risk of crushing of skin and limbs due to
- Spring force/gravity (stored energy).
- Falling conductor rail system components, if they have not been properly installed or if operated under inappropriate operating conditions (e.g., environment that contains solvents).
- Only allow installation to be conducted by specialized technicians.
- Wear personal protective equipment!
- Further information on the installation of the conductor rail system can be found in the operating instructions BAL0813-0007
ASSEMBLY
The disassembly tool consists of two tools and is an aid for removing a hanger clamp from the conductor rail. Tool 1 is pushed between the hanger clamp and conductor rail, while Tool 2 opens the hanger clamp.
- Slide Tool 1 up to the stopper between the conductor rail and hanger clamp (see Fig. 3).
- Press the conductor rail against Tool 1 or against the hanger clamp, respectively (see Fig. 4). At the same time, insert Tool 2 on the open side of the conductor rail (see Fig. 6). The retaining clamp of the hanger clamp bends up (see Fig. 5).
- Fig. 3: Slide Tool 1 between the conductor rail and the hanger clamp
- Fig. 4: Press the conductor rail against Tool 1 or against the hanger clamp
- Fig. 5: The retaining clamp of the hanger clamp bends up
- Fig. 6: Insert Tool 2 on the open side of the conductor rail
- Pull out the conductor rail.
- Remove Tool 2 from the open side of the conductor rail (see Fig. 8).
- Fig. 7: The hanger clamp bends up
- Fig. 8: Remove Tool 2 from the open side of the conductor rail
- In order to remove Tool 1, the tension spring of the retaining clamp may need to be pushed away.
- Fig. 9: Remove Tool 1
Use the QR code (“click” or “scan”) to see our animation Disassembly Tool.
Conductix-Wampfler GmbH
Rheinstraße 27 + 33
79576 Weil am Rhein – Märkt
Germany
Phone: +49 (0) 7621 662-0
Fax: +49 (0) 7621 662-144
info.de@conductix.com
www.conductix.com
Importer for the United Kingdom:
Conductix-Wampfler Ltd.
1, Michigan Avenue
Salford
M50 2GY
United Kingdom
Phone: +44 161 8480161
Fax: +44 161 8737017
info.uk@conductix.com
www.conductix.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>