CONDUCTIX wampfler Program 0380 Motorized Cable Trolley Instruction Manual

June 3, 2024
Conductix Wampfler

CONDUCTIX wampfler-logo

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig1

Required Tools

  • Wrenches for Sizes

    • 10 mm (all types suitable)
    • 13 mm (all types suitable)
    • 17 mm all types suitable
    • 19 mm (open-end wrench needed for one step; all other types suitable for other steps)
    • 36 mm (open-end wrench)
  • Belt Tension Measuring Device

  • Soft Head Hammer

  • Gear Puller

Working Steps

CAUTION

  • Risk of injury!
    • Secure the motorized festoon system from unexpected switch-on
    • Safety devices that have removed must be immediately remounted and inspected after work has been completed
    • Any used measuring tools must be cleaned up/collected after completion and their inventory must be checked
    • Before approaching systems with damping devices, they must first be released

NOTICE!: The main roller can only be replaced together with the drive shaft for the main roller.

Disassembly Steps

  1. Dismount protective cover.
    Loosen the 6 screws (1), 3 turns and dismount the cover (2).

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig6

  1. Dismount tooth belt (1).
    Untighten nuts (2 and 3) to retract tension pulley.
    Remove tooth belt (1) without applying force to it

  2. Remove screws (3) and dismount bracket (4)

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig8

  1. Remove screws treated with chemical thread (9) and dismount locking washer (10).

  2. Remove screw (11) and take off toothed belt disk (12) with covering disk (13).

  3. Lift up the motorized cable trolley until the main roller to be replaced (14) is no longer positioned on the track beam.

  4. Remove feather key (15).

  5. Remove screws (16) and dismount complete bearing housing (17).

  6. Remove distance sleeve (18).
    Dismount safety ring (21). Remove nilos-ring (only 3 KW).

  7. Push drive shaft (19) out of the bearing housing in the direction of the arrows.

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig12

Assembly Steps
The assembly is made in reverse order. Use the new standard and connecting elements.

  1. Press new drive shaft (19) into the bearing housing.
    To do this support the bearing housing on the inner ring of bearing 1 (22).

  2. Mount nilos-ring (20) and safety ring (21) (only 3 KW). Afterwards press on the distance sleeve (18)

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig13

  1. Clean contact surfaces. The surfaces must be absolutely clean.

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig14

  1. Install the bearing housing (17), it aligns via the two cylindrical pins.

  2. Mount the screws (16).

  3. Place the feather key (15) into the groove.

  4. Push toothed belt disk (12) onto the drive shaft.

  5. Mount cover disk (13) with screw (11).

  6. Mount locking washer (10) with screws treated with chemical thread locker (9).

  7. Put down the motorized cable trolley on the beam.

  8. Mount bracket (6) for guide roller with screws (5) (only 1.95 KW).

  9. Mount bracket (4) for protective cover with screws (3). Lock the screws with LOCTITE 243.

Mount bracket (4) with screws (3). Lock the screws with LOCTITE 243.

NOTICE!

  * After 6.000 crane operating hours both tooth belts must be replaced.  

Assembly works at the tooth belt drive must comply with the particularities of the belt design. The operating behavior, utilization and the lifetime are dependent on the quality of the producer’s recommendations.

  * In case of worn out or defective tooth belt, always replace both tooth belts.
  1. Mount tooth belt.
    Put on tooth belt (1) without applying force to it.
    Tighten nut (3) to extend tension pulley.
    Check and adjust tooth belt (1) tightening (for details see Mounting Instructions).
    Secure belt tensioner by tightening nut (2)

CONDUCTIX wampfler Program 0380 Motorized Cable Trolley-
fig20

  1. Mount protective cover.

ABOUT COMPANY

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Conductix Wampfler User Manuals

Related Manuals