Lenovo 61FCMAT6EU ThinkVision T24v-20 24 Inch FHD Monitor Instruction Manual

October 30, 2023
Lenovo

Lenovo 61FCMAT6EU ThinkVision T24v-20 24 Inch FHD Monitor

Lenovo-61FCMAT6EU-ThinkVision -20-24-Inch-FHD-Monitor-
PRODUCT

Product Information

Lenovo T24v-20 Monitor

The Lenovo T24v-20 is a monitor with a 23.8-inch display and a resolution of 1920 x 1080 pixels. The monitor has an IPS panel with a 178-degree viewing angle and a contrast ratio of 1000:1. It also has a response time of 4ms and a brightness level of 250 nits. The monitor has an HDMI port, a VGA port, and a USB hub with two USB 3.0 ports.

Product Usage Instructions

Dismantling

If you need to dismantle the Lenovo T24v-20 monitor, follow these instructions:

  1. Precaution: Before starting the dismantling process, make sure all power connectors are removed and the monitor is turned off. Prepare a soft cloth and sponge as a working platform to place the LCD monitor horizontally. Carefully hold the LCD by the side and avoid touching or pressing the panel directly.
  2. Appropriate tools: Select the appropriate tools for disassembly and re-assembly, including a Phillips screwdriver (#2), spacer screwdriver, C/D disassembly tool, and gloves or soft cloth.
  3. Disassembly SOP:
  4. Put the monitor on a flat surface (put the EPE on under the monitor).
  5. Push the button to release the stand.
  6. Remove the four screws using a screwdriver #2.
  7. Use the C/D disassembly tool to release Rear cover hook from disassemble hole on bottom.
  8. Remove the chassis screw and all tape and light bar connector using a screwdriver #2.
  9. Hold the main chassis to release the Panel cable and overturned the chassis.
  10. Take out the mylar sheet from Main chassis.
  11. Remove PCB screw and peel off the tape of all using a screwdriver #2 and spacer screwdriver.
  12. Hold the PCB and release all connectors.
  13. Remove screws to take out the front bezel using a screwdriver #2.
  14. Remove screws to take out the Camera module using a screwdriver #1.
  15. Use force to release the knob as shown by the red arrow and take out the camera stand and knob.
  16. Remove screws to take out the camera stand using a screwdriver #1.
  17. Remove screws to take out the Camera hinge using a screwdriver #1.
  18. Use force to release the camera front and camera back cover as shown by the red arrow.

Note: These instructions are only for dismantling the Lenovo T24v-20 monitor. For any other issues, please refer to the user manual or contact customer support.

Exploded Diagram

Lenovo-61FCMAT6EU-ThinkVision -20-24-Inch-FHD-Monitor-
FIG-1

Precaution

  • Please read the precaution as follows to prevent any damages to the LCD Monitor.
  • Make sure all power connector is removed. Be sure that the LCD Monitor is in power off status.

Prepare soft cloth and sponge as working platform

to place LCD monitor horizontally.

|
---|---
Hold LCD by the side carefully and DON’T touch or press panel directly.|

Appropriate tools

Select the Appropriate tools for disassembly and re-assembly.

Phillips screwdriver (#2)|
---|---
spacer screwdriver|
C/D disassembly tool|
Gloves or soft cloth|

Disassembly SOP

Put the monitor on a flat surface (Put the EPE on under the monitor)| Lenovo-61FCMAT6EU-ThinkVision -20-24-Inch-FHD-Monitor-
FIG-8

---|---
Push the button to release the stand| *
Remove the screw
4pcs Tool : Screwdriver #2| **

Use the C/D disassembly tool to release Rear cover hook from disassemble hole on bottom| ****
Remove the chassis screw. Remove All tape and light bar connector

Tool : Screwdriver #2

|

---|---
Hold the main chassis to release the Panel cable and overturned the chassis|


Take out the mylar sheet from Main chassis| ****
Remove PCB screw and Peel off the tape of all.

Tool : Screwdriver #2 And Spacer screwdriver

|
Hold the PCB and release all connector.|

Remove screws to take out the Front bezel.

Tool : Screwdriver #2

|

---|---
Remove screws to take out the Camera module

Tool : Screwdriver #1

|
Used the force to release the knob as red arrow showing.|

Take out the camera stand and knob.| ****
Remove screws to take out the Camera stand

Tool : Screwdriver #1

| ****
Remove screws to take out the Camera hinge

Tool : Screwdriver #1

|

---|---
Used the force to release the camera front and camera back cover as red arrow showing.| ****

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Lenovo User Manuals

Related Manuals