LAPETEK JONA SLIM-V 90 Island Kitchen Hood User Manual

LAPETEK JONA SLIM-V 90 Island Kitchen Hood User Manual

Product Information: JONA SLIM-V 90

The JONA SLIM-V 90 is a cooker hood designed for domestic use. It is available in three colors: black, stainless steel, and white.
The product code for the black version is 57009, for the stainless steel version is 57007, and for the white version is 57008. The appliance has a product version number of 001.

The dimensions of the JONA SLIM-V 90 are 905-1140mm (width) x 905-1140mm (depth) x 40mm (height). It has a maximum extraction rate of 600m³/h and a noise level of 130dB. The product comes with a grease filter and a single-use charcoal filter.

Before installation and use, it is important to read and follow the instructions provided in the user manual. Always keep the manual with the appliance for future reference.

Product Usage Instructions: JONA SLIM-V 90

1. Ensure that the appliance and its parts are not damaged before installation. If there is any damage, contact your dealer.
2. Installation work must be carried out by a professional.
3. During installation and maintenance procedures, wear protective gloves.
4. Before cleaning or maintenance, unplug the appliance or remove the fuse.
5. Do not use the appliance without a grease filter.
6. Ensure there is adequate exchanging air from outside in the room by opening a window when the hood is in use.
7. Clean the appliance and grease filter when necessary.
8. The grease filter must be cleaned regularly (whenever necessary or at least every 3 months) to prevent risk of fire. It can be washed in a dishwasher but should not be washed using the longest and hottest washing programs.
9. Single-use charcoal filters must be replaced at 3-4 times a year depending on usage.
10. The machine-washable Long Life charcoal filters (accessory) can be cleaned and activated by washing them in the dishwasher at 65 degrees.

This installation manual applies to the following products

For your safety and correct operation of the appliance, read this manual carefully and thoroughly before installation, wiring and use. Always keep these instructions with the appliance.

SAFETY INFORMATION

• All installation work must be carried out by a professional.

• Before installation, make sure neither the appliance nor its parts are damaged. Otherwise, please contact your dealer.
  Do not install a defective product! An installed appliance is considered tested and approved.

• Always follow the instructions in this manual. Lapetek is not liable for any damage, fires etc., resulting from improper or incorrect installation or use.

• The installation of the appliance must be carried out in a way that the cooker hood can be removed for maintenance without dismantling other room structures. In case of warranty maintenance, Lapetek is not liable for any costs resulting from dismantling other structures.

• The cooker hood may look different from the drawings in this booklet. However, instructions of use, maintenance and
  installation remain the same. Make sure the product and its version number correspond to the information in the manual.

• Always wear protective gloves during installation and maintenance procedures.

• The cooker hood is designed for extracting cooking fumes and is for domestic use only.

• Unplug the appliance or remove the fuse before cleaning or maintenance.

• Never use the appliance without a grease filter.

• Do not store or place anything on top of the appliance.

• Make sure there is adequate exchanging air from outside in the room by, for example, opening a window when the hood is in use. Inadequate ventilation prevents the hood from working properly.

• Do not flambé or set an open fire under or near the appliance.

• The amount of grease inside the hood and the grease filters should be monitored regularly by removing the grease filter and cleaning both the appliance and the grease filter when necessary.

• The grease filter must be cleaned regularly (whenever necessary or at least every 3 months) to prevent risk of fire.
  The grease filter can be washed in a dishwasher. Do not use the longest and hottest washing programs. The grease filters will wear out and should be replaced when their surface/color begins to be worn or faded.

• Single-use charcoal filters must be replaced at 3-4 times a year. However, the frequency in which the filters need to be replaced depends on usage.

• The machine-washable Long Life charcoal filters (accessory) are cleaned and activated by washing them in the dishwasher in 65 degrees. Please note that no other dishes are to be washed at the same time as the charcoal filter. Afterwards the filters are placed in a 100-degree oven on the grid for 10 minutes with upper and lower heat set. Cleaning and activating the filters should be done approximately every two months. After three years, the efficiency of the LongLife filters will be reduced by approximately 50% of the original.

CONTROL PANEL FUNCTIONS

Start
The appliance starts with the key for speed 1. The speed increases with every push of the key to the next higher speed 2,3, or 4. Speed 4 is intensive speed and only on for 5 minutes before returning to speed 3. The speed is reduced and the appliance is turned off using the key.

Timing
When pressing the timer key while the engine is running at speed 1, 2, or 3, the engine stops after a set time,  extracting the fumes of a hot pan on the cooker while the pan is cooling.

When the timer key is pressed, the number 0 will begin to flash on the display. Within 20 seconds the key can then be pressed to set the timer: the number on the display changes to represent the number of times (1,2,3…) the key is pressed, which in turn represents the timer setting (1=10, 2=20, 3=30, 4=40, 5=50, 6=60, 7=70, 8=80, 9=90 minutes).

Lighting control and dimming
Pressing the key briefly turns the lights on / off. The lights turn on at full luminous intensity suitable for working. In addition,
the lights have a three-stage dimming function. When the lights are on at full power, pressing the key for three seconds will dim the lights to general lighting. When pressing the key once more for three seconds, the lights dim to ambient lighting. The lights always turn on at full luminous intensity.

Color temperature adjustment
Pressing the and keys simultaneously activates the color temperature adjustment of the lights and the letter L starts flashing on the display. Pressing the key increases the color temperature (max. ~ 6000 K) and pressing the key decreases the color temperature (min. ~ 3000 K). The selected color temperature remains set if the switch panel is not touched within 20 seconds.

INSTALLATION HEIGHT

• The maximum installation height is 750 mm from the cooker. In this case, the ceiling height of the room can be 2730 mm (please take into account all the other dimensions and measurements in the picture).
• A taller, 860 mm lower part of the chimney pipe is available as an accessory.

REPLACEMENT OF LIGHTING

1. Remove the grease filters before replacing the lamp.
2. Push the lamp gently inwards to release it from the body of the hood. Gently push the lamp inside the hood in the direction of the arrow pressing from outside to loosen it.
3. Carefully pull out the lamp.
4. Disconnect the cable (quick connector 5) and replace the lamp. Install the new lamp in reverse order. Finally, slide the lamp back into place.

WARRANTY AND MAINTENANCE

• Lapetek cooker hoods are covered by a two-year (2) warranty. Lapetek is not liable for any indirect defect or damage. The warranty does not cover consumable parts such as lamps, light sources, filters, etc.
• This device is manufactured in accordance with EU Directive 2012/19/UE (SER).
• Cleaning the grease filter (for further instructions, see installation instructions steps 12-14).
• Replacing the charcoal filter (for further instructions, see installation instructions step 15).
• Replacing the LED-light (for further instructions, see page 6).
• Additional information: lapetek.fi 

INSTALLATION

1. Remember to wear protective gear.

2. Installation either ducted or recirculated (with optional charcoal filter). Includes a 1,5 m long power supply cable and a 120/150 flue connection reducing socket and a non-return valve.

3. Measurements of the appliance.

4. Mark the exact middle of the appliance in the ceiling in relation to the cooker

5. Minimum distance from the cooker:
   Electric cooker 55 cm, Gas cooker 65 cm, Recommended max. installation height 75 cm from the cooker.

6. For ceiling mounting, use fasteners recommended by the ceiling manufacturer, available from hardware stores.

7. Use either a 160 mm or 125 mm vent pack.

8. Note the space required by both the power supply cable and the chimney pip.

9. Lift up the ceiling frame (A) to the previously marked area on the ceiling and secure it at the four corners. Ensure the length of the chimney pipe before finalizing the installation to the ceiling

10. Place the chimney pipes (one inside the other) in the ceiling frame

11. Temporarily secure the chimney pipes in the up position with a screw to make sure they do not fall down and prevent the hood from being attached to the ceiling frame.

• Lift up the body of the hood to the ceiling frame and secure with 4 screws.

• Remove the screw secured in figure 11 and lower and secure the lower part of the chimney pipe to the hood.Secure the upper part to the top of the ceiling frame with screws

• Removing the grease filter. Connect the cables for the lights and control panel behind the grease filters

• Inserting the grease filter.

• The grease filter can be washed in a dishwasher. Do not use the longest and hottest washing programs.
  The grease filters will wear out and should be replaced when their surface/color begins to be worn or faded.

• Installing the charcoal filter.

PRODUCT TEST DOCUMENT

INSTALLER SIGNED PRODUCT TEST DOCUMENT
During installation, the installer must check the points below. Please note that the first checkpoints take place before the actual installation. By signing the document, the installer ensures the installation has been carried out in accordance with the installation instructions and that the appliance is functioning properly and is flawless.

Before installation:

1. The appliance is externally in good condition when removed from packaging and includes all its parts. The appliance has no imperfections/visible defects/color defects/bumps/scratches/etc.                                       

2. Before mounting on the wall/ceiling or under the cabinet: all motor speeds work, the suction power is perfect and there are no abnormal noises from the motor.                                                                                                 

3. The lights work.                                                                                                                                                                                                                                                                                                                                                                       

4. The timer works.                                                                                                                                                                                                                                                                                                                                                                     

5. The non-return valve is installed and working.                                                                                                                                                                                                                                                                                                                 

6. There are no strange noises from the cooker hood.                                                                                                                                                                                                                                                                                                         
   After installation:

7. The suction power is perfect after installation. In case the suction power is poor after installation, the part of the ventilation duct causing the decrease in power must be determined.                                                             

• In case any of the checkpoints 1) to 6) above are not in order, the installer must immediately contact the seller/customer as well as Lapetek service at +358 9 2511 030 for further information.
• In case checkpoint 7) is not in order, the installer must contact the customer/seller and let them know that the house has a problem in the ventilation duct that decreases airflow.
• The warranty granted by Lapetek is conditional on the completion of this document and the certification of the condition of the checkpoints. A copy of the test document must be submitted with a reclamation.

Installer’s signature
Date and place____
Clarification of the installer’s name
Company name___

CONTACT
Oy Lapetek Ab
Website: www.lapetek.fi
Sales, technical support and service: sales@lapetek.fi

References

• Lapetek
• Lapetek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>