LAPETEK 590ACX1 Island Stainless Steel User Manual

APOLLO-V X1
Installation and user manual

590ACX1 Island Stainless Steel

This installation manual applies to the following products

For your safety and correct operation of the appliance, read this manual carefully and thoroughly before installation, wiring and use. Always keep these instructions with the appliance.

SAFETY INFORMATION

• All installation work must be carried out by a professional.

• Before installation, make sure neither the appliance nor its parts are damaged. Otherwise, please contact your dealer.
  Do not install a defective product! An installed appliance is considered tested and approved.

• Always follow the instructions in this manual. Lapetek is not liable for any damage, fires etc., resulting from improper
  or incorrect installation or use.

• The installation of the appliance must be carried out in a way that the cooker hood can be removed for maintenance without dismantling other room structures. In case of warranty maintenance, Lapetek is not liable for any costs resulting from dismantling other structures.

• The cooker hood may look different from the drawings in this booklet. However, instructions of use, maintenance and installation remain the same. Make sure the product and its version number correspond to the information in the manual.

• Always wear protective gloves during installation and maintenance procedures.

USE

• Speed 1 is used for extracting cooking fumes and basic ventilation.
  Increase the speed as the fumes become stronger or when more efficient ventilation is needed. Use maximum speeds only when necessary.

• Make sure there is adequate exchanging air from outside in the room by, for example, opening a window when the hood is in use. Inadequate ventilation prevents the hood from working properly.

• The cooking hood can be cleaned with all-purpose kitchen cleaner which can be purchased at grocery stores. After cleaning, the detergent residues must be removed with a clean, damp cotton cloth (or similar)  that doesn’t scratch the surface.
  Residues that have not been properly rinsed and dried may result in changes on the surface of the cooker hood, e.g. rust-like changes in color.

• The cooker hood is designed for extracting cooking fumes and is for domestic use only.

• Unplug the appliance or remove the plug before cleaning or maintenance.

• Never use the appliance without a grease filter.

• Do not flambé or set an open fire under or near the appliance.

• The amount of grease inside the hood and the grease filters should be monitored regularly by removing the grease filter and cleaning both the appliance and the grease filter when necessary.

• The grease filter must be cleaned regularly (whenever necessary or at least every 3 months) to prevent risk of fire. The grease filter can be washed in a dishwasher. Do not use the longest and hottest washing programs.

• The grease filters will wear out and should be replaced when their surface/color begins to be worn or faded.

CONTROL PANEL FUNCTIONS

When the appliance is connected to mains power source, the operational mode of the appliance must be set to X1 (within 1 minute of connecting to mains current) by pressing the and keys simultaneously for at least 4 seconds. After, press the ****or  keys until number 1 (= X1 mode chosen) appears on the display. Save the X1 mode by pressing the timer key .The operational mode of the appliance can be re-set by disconnecting and re-connecting the appliance to mains current.
When pressing the timer key while the engine is running at speed 1, 2, or 3, the engine stops after a set time, extracting the fumes of a hot pan on the cooker while the pan is cooling.
When the timer key is pressed, the number 0 will begin to flash on the display. Within 20 seconds the key can then be pressed to set the timer: the number on the display changes to represent the number of times (1, 2 ,3…) the key is pressed, which in turn  represents the timer setting (1=10, 2=20, 3=30, 4=40, 5=50, 6=60, 7=70, 8=80, 9=90 minutes).
Press the timer button to confirm delay.
Timer indicator starts blinking.
After the 180 minutes without any user action, the motor is turned off.

AC-models
Pressing the key briefly turns the lights on/off.
EC-models
Pressing the  key briefly turns the lights on / off. The lights turn on at full luminous intensity which is suitable for working. In addition, the lights have a three-stage dimming function. When the lights are on at full power, pressing the key for three seconds will dim the lights to general lighting. When pressing the key once more for three seconds, the lights dim to ambient lighting. The lights always turn on at full luminous intensity.

INSTALLATION HEIGHT

• The maximum installation height is 750 mm from the cooker. In this case, the ceiling height of the room can be 2820 mm (please take into account all the other dimensions and measurements in the picture).

EXTERNAL MOTOR CONNECTIONS X1/AC

1. ■ The control unit (A) is attached to the cooker hood by screwing as shown in the picture. The PE-wires of the control unit (3 pcs) (B) are attached to the attachment point (C) as shown in the picture.
2. ■ X1/AC Hood with a roof fan: Connect the keyboard cable (F) to the control unit (A). Push the lamp cable (D) inside the chamber as shown in the picture and connect the lamp cables to the connectors leaving of the lamp unit.
   ■ X1/AC Connection: Connect the input cables (E) to the AC roof fan.

EXTERNAL MOTOR CONNECTIONS X1/EC

1. ■ The control unit (A) is attached to the cooker hood by screwing as shown in the picture. The PE-wires of the Control unit (3 pcs) (B) are attached to the attachment point (C) as shown in the picture.
2. ■ X1/EC Hood with a roof fan: Connect the keyboard cable (F) to the control unit (A). Push the lamp cable (D) inside the chamber as shown in the picture and connect the lamp cables to the connectors leaving of the lamp unit.
   ■ X1/EC Connection: Connect the input cables (E) to the EC roof fan.

VENTILATION CONTROL

REPLACEMENT OF LIGHTING

1. Before replacing the lamp, open the hatch.
2. Remove the screws of the back cover and then the back cover.
3. Disconnect the quick connector of the lamp. Replace the lamp and reassemble in reverse order.

WARRANTY AND MAINTENANCE

• Lapetek cooker hoods are covered by a two-year (2) warranty. Lapetek is not liable for any indirect defect or damage.
  The warranty does not cover consumable parts such as lamps, light sources, filters, etc.

• This device is manufactured in accordance with EU Directive 2012/19/UE (SER).

• Cleaning the grease filter (for further instructions, see installation instructions steps 15-16).

• Replacing the LED-light (for further instructions, see page 6).

• Additional information: lapetek.fi

INSTALLATION

1. Remember to wear protective gear.

2. Installation ducted. Includes a 1,5 m long power supply cable.

3. Measurements of the appliance.
   N.B.! Please note the measurements of the ceiling frame when determining the direction of installation.

4. Mark the exact middle of  the appliance in the ceiling in relation to the cooker.

5. Minimum distance from the cooker: Electric cooker 55 cm, Gas cooker 65 cm, Recommended max. installation height 75 cm from the cooker.

6. For ceiling mounting, use fasteners recommended by the ceiling manufacturer, available from hardware stores.

7. Use either a 160 mm (or 125 mm) vent pack.

8. Note the space required by both the power supply cable and the chimney pipe, and mark the mounting point of the frame on the ceiling.

9. Lift up the ceiling frame (A) to the previously marked area on the ceiling and secure it at the four corners. Ensure the length of the chimney pipe before finalizing the installation to the ceiling.

10. Attach the side panels to the ceiling frame.

11. Place the top of the hood (B) in the frame.  

12. Secure the top of the hood to the ceiling frame with screws.
    N.B.! Leave the screws loose and tighten only in step 13, where you’ll attach the lower part of the hood approx. 1 cm over the top part.
    This makes it easier to secure the lower part.

13. Place the lower part of the hood (C) in the frame.

14. Secure the lower part of the hood on the ceiling frame with four screws.

15. Remove the grease filter and connect the cables for the lights and control panel behind the grease filters. Insert the filter back to its place.

16. The grease filter can be washed in a dishwasher. Do not use the longest and hottest washing programs. The grease filters will wear out and should be replaced when their surface/color begins to be worn or faded.

PRODUCT TEST DOCUMENT

INSTALLER SIGNED PRODUCT TEST DOCUMENT
During installation, the installer must check the points below. Please note that the first checkpoints take place before the actual installation.
By signing the document, the installer ensures the installation has been carried out in accordance with the installation instructions and that the appliance is functioning properly and is flawless.

Before installation:

1. The appliance is externally in good condition when removed from packaging and includes all its parts.
   The appliance has no imperfections/visible defects/color defects/bumps/scratches/etc.

2. All motor speeds work and the suction power is perfect.
3. The lights work.
4. The timer works.
5. The non-return valve is installed and working.
6. There are no strange noises from the cooker hood.
7. The suction power is perfect after installation. In case the suction power is poor after installation, the part of the ventilation duct causing the decrease in power must be determined.|
---|---

• In case any of the checkpoints 1) to 6) above are not in order, the installer must immediately contact the seller/customer as well as Lapetek service at +358 9 2511 030 for further information.
• In case checkpoint 7) is not in order, the installer must contact the customer/seller and let them know that the house has a problem in the ventilation duct that decreases airflow.
• The warranty granted by Lapetek is conditional on the completion of this document and the certification of the condition of the checkpoints. A copy of the test document must be submitted with a reclamation.

CONTACT

Oy Lapetek Ab
www.lapetek.fi
Sales, technical support and service
sales@lapetek.fi

References

• Lapetek
• Lapetek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>