FUFU GAGA KF020227-01 66 Inch Integrated LED Indoor Black Ceiling Fan Instruction Manual
- October 30, 2023
- FUFU GAGA
Table of Contents
Installation Instruction
USE AND CARE GUIDE
CEILING FPAN
Security Information
Please read all safety instructions before installing the ceiling fan and save this document for future reference.
- Carefully open the packaging. Remove the items from the box. Place the motor body on carpet or foam to avoid damaging the finish. Do not discard the fan carton or foam insert In the case of returns or repairs.
- To prevent injury and damage, please ensure that the hanging position allows the blade to maintain a gap of 7.6 feet (2.3 meters) and 20 inches (50 cm) with any walls or obstacles, and the installation must support at least 35 pounds (15.9 kg)
- Turn off the power to the fuse box breaker before starting to install the fan.
- Read allinstructions and safety information before installing a new fan.
- All wiring must comply with national and local electrical codes. ANSI/NFPA70. If you are not familiar with wiring, please use a qualified electrician.
- Do not bend the blades when installing or balancing the blades or cleaning the fan.
- o not insert foreign objects between rotating fan blades. Make sure that the installation location you choose allows the fan blades to rotate without obstacles.
- To reduce the risk of electric shock, disconnect the power circuit before installing the lamp kit.
- After installing the fan, please make sure that all installation parts are fixed to prevent the fan from falling.
- Turn off the fan and wait for the blades to stop completely before performing any maintenance or cleaning.
Ceiling fan installation process
1.Pre-installation
1.Mounting Bracket
2.Canopy
3.Canopy Screws
4.Downrod (Shortrod 12. 5cm) (Long pole25cm)
5.Cross pin
6.Cottre pin
7.Yoke cover
8.Motor housing| 9.Motor
10.Blade
11.Lamp panel
12.LED
13. Glass lampshade
14. Receiver
15. Remote control
---|---
2. Tools Needed
You may need the
tools below:
« Screwdrivers
« Wrench
« Ladder| « Wire Strippers
« Insulation Tape
« Power drill
---|---
3. Parts Inventory
1. Mounting Bracket
2. Top Canopy
3. Downrod Canopy
4. Motor Body
5. Lamp panel
6. Chimney| 7. Blades
8. Screws
9. Blades Screws
10. Downrods (5’/10″)
11. Plastic wire nut (not to scale)
12. Receiver
13. Remote control (lucluding battery)
---|---
4. Secure Bracket
» Secure to Outlet Box
If there isn’t an existing outlet box, then install one using the following
instructions:
« Disconnect the power by removing the fuses or turning off the circuit
breakers.
« Secure the outlet box (A) (not included) directly to the building structure.
Use appropriate fasteners and materials (not included). The outlet box and its
bracing must be able to fully support the weight of the moving fan (at least
35 Ibs).
« Figures show three different ways to mount the outlet box (A) (not
included).
Using the existing screws provided with your outlet box to secure the mounting bracket to the outlet box tightly (a loose mounting will the fan to wobble).
* Secure Bracket
« Attach the mounting bracket to the ceiling. There are two types of screws
included in the pack.
« For wooden ceiling Drilling a pilot hole in your ceiling with the power
drills first, then secure the plate with wood screws
« For concrete ceiling Drill a hole in the base material with a hammer drill
and a correctly sized carbide drill bit for the anchor and clean out the hole
of all debris. Knock expansion screw into the hole and then tighten it with a
wrench
5. Assembly of Downrod
» Choose the proper downrod
- Put the downrod through the top canopy and the downrod canopy
- Pass the wire from the motor body through the downrod
- Secure the downrod and motor body with downrod setscrews and celvis pin
6. Mount Fan to Bracket
- Pull out the long screws (Pin) on the hanger and loosen the screws on both sides (Downrod setscrwe).
- Insert the hanger rod into the round hole of the hanger, and pass the long screw through the hanger rod, align it with the hanger hole, and tighten the screw
- Tighten screws on both sides.
Note: Make sure to tighten the three screws on the hanger; otherwise, the fan may shake.
7. Wiring
Insert the receiver into the top of the fan body and make wire connections according to wire colors, labels, and diagram above.
- Wrap each wire connector separately with electrical tape as an extra safety measure.
- After wiring finished, leave the receiver in the bracket and secure it the the electrical tape then secure the canopy to the bracket
8.
Blade Installation
Attach blades to motor by using screws provided in hardware bag.
(* Repeat step until all 5 blades are installed firmly.)
First remove the
motor shell, and then install the blade.
After the blade installation is completed, install the motor shell,
9. Instaliation of Light Kit
- Connect 2-pin male terminal connector from light kit to 2-pin female terminal connector from fan.
- Loosen 3 screws on switch cap.
- Attach light kit pan until 3 screw on switch cap are engaged with 3 key holes on Light kit pan.
- Rotate L ight kit pan slightly until 3 screws heads are engaged in the narrow and of key holes.
- Tighten 3 screws.
Function Inistruction of Emitter
- LED indicated light
- ON/OFF the light—— The first click is 6000K, the second click is 3000K, and the third click is 4500K. Press again to turn off
- OFF the fan
- Speed of thefan (1-6)
- Direction of the fan ( Reverse switch )
- Naturl wind
- Simulate a human burglar lamp
- Delay closing of the fan
- Timing control of the fan
Kindly Renminders
-
Learning code matching mode is used between emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s ”3 OFF the fan’ button for 5 seconds, it can load normally after hearing a long sound “bee”, which means learning
successfully and it can works normally. (PS: Leaming mode is not accepted after turn “ON” the supply power 30 seconds) -
When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
-
When the emitter cannot the receiver, please check there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
-
Low voltage of battery will affect the sensitibity of the emitter and the signal reception acordingly (the indicated light will flash out its waming when the battery get low voltage). must replace if battery is getting low voltage.
-
Please take out the battery from the emitter when leaving unused for long time.
-
Supporting 200W lighting power at maximum.
-
When installing the fan. the fan ceiling cover don’t press the antenna(or other wire). it is easy to breakdown the wire and short – circuited.
Operating Your fan
Turn on the power and check the operation of the fan The remote controls the
fan speed and light.
The appropriate speed settings for warm or cool weather depends on factors
such as the room size, ceiling height, and number of fans.
The switch controls the direction of the blades:
forward or reverse.
A. Warm Weather (summertime)
NOTE: Wait for the fan to stop before reversing the direction of the blade rotation
A. Warm weather-(Forward) A downward airflow creates a cooling effect. This
allows you to set your air conditioner on a highter setting without affecting
your comfort.
B. Cool weather-(Forward) An upward airflow moves warm air off of the ceiling.
This allows you to set your heating uniton a lowering setting without
affecting your comfort.
Maintenance
Here are some suggestions to help maintain your fan
- Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachment twice a year. Make sure they are secure.
- Clean your fan periodically to help maintain its new appearance over the year. Do not use water when cleaning. This could damage the motor, or possibly cause electrical shock.
- Use only a soft brush or lint-free cloth to avoid scratching the finish. Cleaning products may damage the finished
- There is no need to oil your fan. The motor has permanently lubricated bearings.
- If installed in a coastal, humid environment, regular surface cleaning may be necessary to avoid deterioration or oxidizing effects of salt or other corrosive elements. A Damp Location rating is not an assurance of finish durability. Preventative measures should be taken depending on the environmental exposures your fan will undergo to preserve and protect the finish quality and appearance of your fan.
WARNING
Before servicing or cleaning your fan, switch power off at the service panel
and lock the service disconnecting means to prevent power from being switched
on accidentally.
Troubleshooting
Please read all installation instructions carefully.
After reviewing the following tips, if you are unable to solve a problem,
please contact customer service for additional assistance
WARNING
Before servicing or cleaning your fan, switch power off at the service panel
and lock the service disconnecting means to prevent power from being switched
on accidentally.
Fan not reponding to remote control
- Check that all wire connections are secure and made as instructed.
- Verify that power is on and reaching the receiver by a voltmeter.
- Verify that controller batteries are installed with proper polarity as indicated inside the battery cover
Light does not work
- Check wire connections at ceiling and receiver.
- Confirm that LED wire leads and terminal block are properly connected to the LED board.
Fan makes repetitive ticking noise
- Check for obstructions in the rotor path.
- Make sure mounting hardware at the ceiling is secure.
- Make sure all other hardware and blade attachments are tight.
- Give fan adequate “Break in Period” of several hours to several days then repeat steps above.
Fan makes humming noise
- Be sure you are using the control set supplied with your fan
- Make sure all fittings are firmly secured. Loose parts will often cause vibrational noise or humming. Removal and re-attachment can sometimes remedy such resonant vibrational noise.
Fan woobles
- Make sure the mounting plate and hardware at the ceiling are secure and firmly fastened. If necessary, use the wood screws provided to further secure the outlet box to the joist.
- Carefully lower motor housing and verify that the mounting plate is secure to the outlet box, screws are tight.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>