LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board User Manual

June 4, 2024
LUMINOUS

GYROCOPTERS SELF BALA\CING HOVERBOARD
USER MANUAL

Before You Begin

Before You Begin
Before learning to ride your hoverboard, you must read and follow all instructions and warnings in this user manual. It is important that you follow all safety warnings and cautions that appear throughout the user manual and that you use good judgment when you ride your hoverboard.
The Risk of Injury
The hoverboard is a self-balancing, personal hoverboard that uses balancing technology. Balancing technology cannot prevent injury if you do not ride the hoveroard safely. Whenever you ride the hoverboard, it may result in serious injury or death from loss of control, collisions, and fails. To reduce risk of injury, you must read and follow all instructions and warnings in the user manual.

Disposal and Storage Disposal of according to local laws.
Helmet Safety!
Always wear a properly fitted helmet that meets CPSC or CE safety standards when you ride your hoverboard

Main Components

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
2

  1. Foot Mat

  2. Indicator Lights

  3. Power Button
    ON/OFF – Hold for 3 seconds
    Change WOW’ of Lights – Tap the power button once
    LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
3

  4. Charging Port

Charging Your Batteries

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
4

Do NOT insert the power can plug If the charge port, power cord or AC power outlet is wet.
Battery Charge Indicator Light
LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
5
” When the hoverboard is plugged in and charging, the battery charge indicator will be solid red.
” If the battery charge indicator is green, the batteries are fully charged.

Powering On the Hoverboard

Powering On the Hoverboard
Power on your hoverboard by pressing the Power button. The Power button is located on the back side of the hoverboard. The indicator lights will illuminate to indicate the power is ON.
Resetting the Hoverboard

  1. Turn off the hoverboard
  2. Place the hoverboard on top of a flat surface in a way so the wheels aren’t touching the surface (not upside down)
  3. Ensure the center part of the board is completely straight and aligned
  4. Press and keep holding the power button for 20 seconds. You will notice that hoverboard will beep and lights will flash
  5. After 1st set of 20 seconds let go of the power button but let the hoverboard continue to beep and flash for 20 seconds
  6. After 2nd set of 20 seconds, turn off the hoverboard.
  7. Place it back on the floor. Turn it on and give it a try

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
6

Indicator Lights

  1. Warning Indicator Light (Red)
    If red warning lights are flashing, there is an issue with the hoverboard (low battery, over speed, power issue, etc)

  2. Balance Indicator Light (Green)
    The hoverboard is in Balance Mode with a ride on.

  3. Battery Status Indicator Light (Green)
    When power on, the battery status indicator light will be solid green. If it is OFF, power shut off.

  4. Battery Level Indicator Lights (Green)
    Three green Battery Level indicator lights, about 71-100% Power.
    Two green Battery Level indicator lights, about 41-70% Power.
    One green Battery Level indicator light, about 11-40% Power.
    No Battery Level indicator lights, about 10% or less Power.

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
7

Pairing your Bluetooth Device

To pair with a Bluetooth®device follow these steps:

  1. Make sure both the Bluetooth® function in your device and the hoverboard are turned on.
  2. On your device, locate the Bluetooth® device list. Select “Gyrocopters” from the list.

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
8

Resetting Bluetooth® Memory
To reset Bluetooth® Memory, resetting the hoverboard is needed, Refer to typesetting the hoverboard (page 4).

Riding Your Hoverboard

Before riding, make sure your hoverboard is fully assembled and charged, and inspect your hoverboard before each use. Do not ride if any part is loose or damaged. The hoverboard is highly maneuverable and allows you to easily navigate around obstacles. However, to prevent the loss of traction, you must always be careful when riding and learn to identify and avoid unsafe surfaces. Slippery, icy, or wet surfaces, loose materials (sand/gravel), steep slopes, and obstacles might affect the hoverboard’s performance. Familiarize yourself with the indicator lights that may be displayed on the hoverboard.
Step 1. Power ON the hoverboard by pressing the power button, and make sure the Battery Status Indicator light is on.

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
9

NOTE The hoverboard comes with the No-Fall Technology mode turned on. This feature keeps the board upright whether you are standing on it or not. To turn off this feature, make sure the hoverboard is off. Now double-click the power button when turning it on (tap twice in quick succession). You will hear the normal power-on beep tone, followed by a longer beep tone. The No-Fall Technology mode is now turned off.
Step 2: Getting on the Hoverboard

  1. Place one foot on the foot mat, keeping your weight on the foot that’s still on the ground to prevent unwanted movements from the hoverboard, making it difficult to step on.
  2. When ready, shift your weight to the foot placed on the hoverboard, stepping on with your second foot quickly and evenly.
  3. Once on, find your center of gravity by trying to stand on the hoverboard as if you were standing on the ground. On average it takes 3-5 mins to get comfortable standing on the hoverboard before getting into movements. Having a spotter will help you feel more secure.

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
10

Step 3: Moving forward and backward

  1. Keep Hoverboard still by remaining level when standing on it.
  2. SLIGHTLY lean your body forward or backward to enable the hoverboard to move forward or backward respectively.

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
11

NOTE: When the hoverboard is unable to achieve a balanced position, an alarm will sound and trigger the Warning Indicator light. The hoverboard will return to a balanced position automatically. During this process, you should not step or ride the hoverboard.

  • Body leaning should be done in small increments. Only small leaning angles are needed to drive the hoverboard forward or backward.
  • Leaning forward or backward too much can affect riding safety.

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
12

  • Do not turn while in high speeds to avoid dangerous situations.
  • The hoverboard balances front to back but not side-to-side. Avoid riding across steep slopes. 2

Step 4: Steering the Hoverboard

LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
13 Step 5: Getting off the Hoverboard
Make sure the hoverboard is completely stopped and stable before stepping off. Step off the hoverboard one foot at a time.

Safety Alerts

While operating, the hoverboard can alert users if there are any irregularities in the system. If the hoverboard detects a fault in any of its redundant systems or the batteries are depleted beyond the limit, it automatically slows down the motors. Flashes warning indicator light emits a warning tone and disables self-balancing mode.
Here are some reasons that will trigger the Warning Indicator Light:
— Irregular platform angle
— Low Battery Voltage
— Plugged in and Charging
— Platform distortion while riding (System Shutdown)
— Speed Limited reached
— Platform angle is greater than 35 degrees, (System Shutdown)
— Wheels get stuck
— Electrical Current Surge

  • Risk of Fire, No User Serviceable Parts
  • Do not get back on the hoverboard until the condition that caused the warning alert has been identified and corrected.
  • Never restart and ride your hoverboard after it has indicated an empty Battery condition or shut down due to low Battery. The hoverboard may not have enough power to keep you balanced. If you restart and continue riding, you risk failing. Also, you risk damaging your batteries, resulting in reduced battery life and capacity.

Driving Safely

When riding the hoverboard you risk serious injury from loss of control, collisions, and fails. It is your responsibility to learn how to safely ride the hoverboard in order to reduce this risk. To ride safely you must follow all instructions in the user material, including the user manual.
– Always wear proper attire when using the hoverboard, do not wear loose clothing that can catch in the tires, and prevent proper steering.
– Never place anything on the foot mats except your feet.
– Avoid obstacles and surfaces that could result in a loss of balance or traction and cause a fall
– Use caution when riding over any terrain change such as pavement to sand, grass, or speed bumps.
– Avoid riding across steep slopes, and maintain both tires in contact with the ground.
– Avoid holes, curbs, and other obstacles.
– Avoid riding over any surface where the bottom of the hoverboard may impact any object.
– When using in the sidewalk, make sure that on the wheel does not drop off the curb,
– Use caution when riding in new environments.
– Make sure you leave enough wheel clearance .
– Be careful and considerate of others while riding.
– Always ride under control at a speed that is safe for you and those around you.
– Always be prepared to stop.
– Respect pedestrians by always yielding the right of way.
– Avoid startling pedestrians, When approaching from behind, announce yourself and slow down to walking speed when passing, and pass on the left whenever possible. When approaching a pedestrian from the front, stay to the right and slow down.
– In heavy pedestrian traffic conditions, slow down and proceed at the pace of pedestrian traffic. Pass only if there is ample space to do so safely. Do not weave in and out of pedestrian traffic.
– When riding with other hoverboard riders, maintain a safe distance, identify hazards and obstacles, and do not ride side-by-side unless there is plenty of room left for pedestrians.
– Crossroads at designated crosswalks or signaled intersections. Do not jaywalk/ride.
– Only travel on a road when a pedestrian way is not available or when sidewalk use is not allowed. Do not ride your hoverboard on private property (inside or outside) unless you have obtained permission to do so.
– Learn about and obey applicable local laws and regulations.
– Inspect your hoverboard before you ride it.
– Do not allow any person to use your hoverboard unless that person has carefully read this Manual.
– Use caution on slopes, use caution when ascending, descending, or crossing slopes. When riding across any slope. Lean uphill to maintain balance
– Always turn slowly and with caution, Fast turns can lead to loss of control and failure.
– No passengers. The hoverboard is designed for only one rider, Do not double or carry any passengers. Do not carry a child in your arms or in a child carrier while riding. Expectant mothers should not ride the hoverboard.
– Do not exceed the maximum weight limit (rider and all cargo) specified in this Manual. If you exceed the maximum weight limit, you are at greater risk of failing and injury. Also, the rider’s weight must not be less than the minimum rider weight limit specified in this manual.
– Do not step off the hoverboard while moving Always come to a stop before stepping off.
– Be alert. As with any other transportation device, you must be mentally alert to safely ride. Do not attempt to ride if you are ill or if you cannot comply fully with the instructions and warnings in this manual. Do not ride under the influence of alcohol or drugs. Avoid distractions. Do not use a mobile phone, or engage in any other activity that might distract you or interfere with your ability to monitor your surroundings while riding.
– When riding, keep both feet on the foot mats. Be relaxed, Ride in a relaxed position with your knees and elbows slightly bent and head up.
– Do not ride backward for long periods of time. Instead, turn and ride forward.
– Riding on the road. The hoverboard is not intended or recommended for primary use on roads. If you must ride on the road, or must cross the road, be extremely careful. Ride as far away from traffic as possible. Check to make sure that riding on the road is allowed by local law.
– Ride in areas free of obstacles and distractions until you are comfortable using and maneuvering your scooter, Practice until you can step on, ride forward and backward, turn, stop, and step off without any problems.

Technical Specifications

Lithium-ion Battery 2.0Ah, 36V 72WH
Motor Dual Motor with Dual Independent Gyros
Distance on full charge Up to 60 mins
 Charging Temperature 0 C to 40 C / 32 °F to 104 °F
Charging time 2 to 3 hours
Input DC 42V 1A
Max Speed  12 km/h . 7.4mPH
Max Weight 75KGs / 165 LBS
Minimum Weight  15KGs / 33 LBS
Max Climbing Limit 15 degree
Temperature -10 C to 50 C /14°F to 122°F
Frame Material Aluminum with Plastic Components
Wheel size 165mm / 6.5 inch
Product Dimensions 601188178 mm / 23.67.42 7 inch
Net Weight 10kgs / 22LBS

Battery Safety

– Do not use a Battery if the battery pack casing is broken or if the battery emits an unusual odor, smoke, excessive heat or leaks any substance. Avoid contact with any substance seeping from the Batteries.
– Keep out of reach of children and pets. Exposure to battery voltage could result in death or serious injury.
– Unplug or disconnect the hoverboard from AC power before removing or attaching Batteries or performing any service. Never work on any part of the hoverboard when it is plugged into an AC power source. You risk serious bodily injury from electric shock as well as damage to the hoverboard.
– The cells within the batteries contain toxic substances, Do not attempt to open the batteries. Do not insert any object into the batteries or use any device to pry at the battery casing. If you insert an object into any of the battery ports or openings you could suffer electric shock, injury, burns, or cause a fire. Attempting to open the battery casing will damage the casing and could release toxic and harmful substances, and will render the pack unusable.
– Observe and follow all safety information on the warming label found on the batteries
– Failure to charge the batteries could result in permanent damage to them. Left unplugged, the batteries could fully discharge over time, causing permanent damage.
– Use only charging devices approved by the hoverboard and never attempt to bypass or override their charging protection circuits.
– Do not attempt to wash the hoverboard with a power washer or high-pressure hose. Avoid getting water into the charge port. Always close the charge port cover after charging is completed. Make sure that the Charge port is dry before you plug in the power cord, Failure to follow these instructions could expose you to electric shock, injury, burns, or cause a fire.
– Do not submerge the batteries or platform in the water, If you suspect the Batteries or powerbase have been submerged or experienced water intrusion, do not attempt to remove the batteries. Do not plug the Power Cord into the scooter. Failure to follow these instructions could expose you to electric shock, injury, burns, or cause.
– As with all rechargeable batteries, do not charge near flammable material.
– If you use, charge, or store the hoverboard batteries outside the limits specified, you may void the limited warranty, damage your batteries, and/or experience the reduced range and ineffective battery charging.
Note: Lithium-ion batteries are regulated as “Hazardous Materials”. Transporting Lithium batteries by air, or other methods might be prohibited by policies or law. Please contact the designated agents from the carrier company for more details.
WARNING: The covers of the motor are plastic, please do not let it fall vertically!
LUMINOUS EL-ES12 Gyrocopters Self Balancing Hover Board - fig
14

Warranty Details

Gyrocopters offer 90 days warranty on all products. 90 days warranty commences from the date of purchase. Please retain your payment receipt/order#, and original packaging for proof of purchase and to claim your warranty/repairs. All defective merchandise are eligible for repair within 90 days of the original purchase date. This warranty DOES NOT cover normal wear and tear or any other physical damage or liquid damage caused to your parts/unit by improper usage or handling. The warranty does not cover over-charging, or damages due to improperly maintaining the lithium battery installed in the unit. Opening and altering the device will void any original manufacturer warranty. By opening your unit, you acknowledge that you assume all responsibility for your device, and its functionality or lack thereof. We assume no liability for loss or damages caused by unsafe riding and/or improper usage. Our warranty does not cover when used unsafely or out of limits.
Gyrocopters will only accept returns or unused and undamaged products that are returned in the original packaging within 14 days of your purchase date.
IMPORTANT: This warranty does not cover physical damages resulting from accident, misuse, or abuse, lack of reasonable care, the affixing of any attachments, stunts, tricks, loss of parts, over-load or subject in the product to any but the specified voltage. The use of unauthorized replacement parts will void the warranty. This warranty is only eligible for the purchase of the initial Gyrocopters Luminous Hoverboard. No responsibility is assumed for any special incidental or consequential damages.

Contact Details:
Gyrocopters e-mobility systems
www.gyrocopters.ca
For support: customercare@imgadgets.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals