hager SL200559409011 Berker Push-Button Instruction Manual
- October 30, 2023
- hager
Table of Contents
Operating and
assembly instructions
6LE008010A
2412 XXXX
Berker push-button
Friends of Hue
Instruction Manual
Safety instructions
Electrical equipment must only be installed and assembled by a qualified
electrician in accordance with the relevant installation standards,
regulations, directives and safety and accident prevention directives of the
country.
Failure to comply with these instructions may result in damage to the device,
fire or other hazards.
The radio transmission is not suitable for safety or alarm applications.
These instructions are an integral component of the product and must be
retained by the end user.
Design and layout of the device Image 1: Fundamental design and
layout of the device
-
Locking spigot
-
Frame (not included)
-
Berker push-button
-
Rocker 2gang
-
Locking pins
-
Supporting plate
Image 2: Design and layout of the device adhesive foil -
Adhesive foil
-
Backing film
-
Protective film
Function
Correct usage
– Smart light switch for wireless control of Philips Hue lamps.
– For switching, dimming and controlling individual light scenes
– Radio application in acc. with RED 2014/53/EU with particularly low energy
consumption.
– Installation on device box, render or level surfaces with screws and
adhesive pads.
– Only suitable for use in indoor areas with no drip and no spray of water.
Berker push-buttons are suitable for residential use only and require a
Philips Hue Bridge (v2) and Philips Hue App for Android or iOS for initial
commissioning.
Philips Hue lamps can only be controlled by the Hue system when the light is
switched on. Please ensure that the Philips Hue lamps are always switched on.
Please be aware that Signify has access to personal data and user data via the
Hue Bridge. Signify’s privacy policy and terms and conditions of use are
available at www.philips-hue.com. The processing
of personal data and user data is explained there.
Product characteristics
– Batteryless and maintenance-free device without external power supply.
– Encrypted transfer with device-specific code.
– ZigBee Green Power radio standard, compatible with Friends of Hue and Apple
HomeKit.
– Automatic extended reach via Philips Hue lamps.
– Easy commissioning and configuration via Philips Hue App and Hue Bridge v2 .
– Transmission power is obtained from mechanical energy when the button is
pressed (energy harvesting).
– Berker push-button consists of 4 push-buttons.
Operation
Operating concept
A short and long press can be allocated to functions on each button
(switching, dimming, scenes).
Information for electricians
Assembly
Selecting installation location
The transmission reach in buildings is approximately 15 m without wall
penetration.
A maximum of one wall penetration is recommended as otherwise the radio signal
is weakened. Image 3: Reduction of range through construction bstacles
The receiver may not be able to properly process the transmitter signal if it
penetrates several walls. Metals, such as metallic door frames, etc., can also
have a negative impact on transmission. The reach can be extended with Philips
Hue lamps in each room. werden.
Information for electricians
Installation
Screwing on the supporting plate Screwing on the supporting plate
DANGER!
Electrical shock when live parts are touched!
An electric shock can lead to death!
Before mounting the supporting plate on a wall box, insulate the terminal
leads that are not required against unintentional contact!
- Screw the supporting plate (6) onto a wall box in the right position and mount them directly on the wall using the supplied screw/anchor set. Ensure that the label “TOP/OBEN” is at the top. Sticking on the supporting plate
Sticking on the supporting plate
CAUTION!
Frame materials such as glass, concrete, slate, metal, aluminium are to be
fastened exclusively with a screw connection!
Device may fall from the wall!
Before using the product by means of adhesive foil, check whether the intended
use is suitable!
The Berker push-button can be mounted on smooth, flat surfaces, such as on
mobile glass office walls.
It is recommended to fasten the Berker push-buttonh with a screw connection
for best hold.
Th optimal processing temperature lies between 15 °C and 25 °C.
After the Berker push-button has been properly adhered to the surface, it
becomes hard to remove. Therefore select installation location carefully
before installation.
Observe installation sequence for optimal adesion of the supporting plate.
Do not touch adhesive surface.
-
Clean mounting surface with a suitable, non-greasing or silicone-containing household cleaner, e.g. isopropyl.
The mounting surface is clean, free of grease and offers sufficient support. -
Remove the surplus backing film (8).
-
Align the adhesive film (7) and stick onto the mounting surface. In so doing, press the adhesive film on firmly – if necessary, with a suitable aid
-
Remove the protective foil (9).
-
Align the supporting plate (6) and stick to adhesive foil for at least 15 seconds. Align the label “TOP/OBEN” to the top. Frame and Berker push-button do not need to be stuck on.
The adhesive pads only reach their final adhesion after approx. 24 hours.
**** Before installation, commission the device and test the reach prior to
using the adhesive film.
Mounting the Berker push-button on the supporting plate
The supporting plate is fastened to the wall.
-
Place the frame (2) onto the supporting plate (6).
-
Place the Berker push-button (3) on the sup- porting plate via the locking spigot. In doing so, observe the labelling in the centre of the module – 0 must be at the top (10) and I at the bottom (11) liegen.
-
Push the yellow locking pins (5) on the left and right of the Berkerpush-button upwards/downwards under the locking spigots (1) up to the stop (Figure 4).
The Berker push-button is locked on the supporting plate. -
Place the rocker (4) onto the Berker push-button in the right position and push it on until it engages.
Image 4: Locked and unlocked Berker push-button
Dismantling the device
-
Push the rocker (4) down. On the opposite side, reach under the rocker and pull it off.
-
Using a screwdriver, push the yellow locking pins (5) on the left and right of the Berker push-button (3) downwards/upwards.
The Berker push-button is unlocked. -
Remove Berker push-button and frame. Unscrew the supporting plate or release from the adhesive film (7).
Commissioning
Follow the Philips Hue App instructions for commissioning and configuration.
Connect Berker push-button to the Philips Hue Bridge.
The Philips Hue Bridge is ready for operation and within reach of the radio
module.
The system requires a Philips Hue Bridge (v2) and Philips Hue app for Android
or iOS for initial setup. Learn more on Philips-hue.com.
The Philips Hue App must be connected with the Philips Hue Bridge.
-
Select the “Settings” > “Accessories setup” > “Friends of Hue Switch” menu in the Philips Hue App.
All compatible Friends of Hue switches are displayed. -
Select Berker push-button.
Operate the buttons (4) of the Berker push-button as described in the app.
The Berker push-button has received the information and has been added as an accessory in the app.
The Berker push-button can be configured in the app.
Configuration
The button functions (switching, dimming, scene) have to be configured in the
Philips Hue App.
Configuring Berker push-button in the Philips Hue app
The Berker push-button is taught-in in the Philips Hue Bridge.
Philips Hue lamps are ready to use.
- Follow the instructions as described in the app and allocate the Berker push-button to the lamps and configure it.
Appendix
Technical data
Carrier frequency: 2.4 … 2.483 GHz
Zigbee Green Power as per IEEE 802.15.4
Transmission range in buildings: approx. 15 m
Transmission power: 7 dBm (5 mW)
Degree of protection IP: IP20
Storage temperature: -25 … +65 °C
Ambient temperature: +5 … +45 °C
Troubleshooting
Philips Hue receiver does not respond.
Cause 1: The Philips Hue lamp has not been switched on.
Switch on the Philips Hue bulb with a conventional switch.
Cause 2: Berker push-button is not connected with the lamp to be switched.
Open the Philips Hue App and check the connection between switch and lamp.
Warranty
We reserve the right to realise technical and formal changes to the product in
the interest of technical progress.
Our products are under guarantee within the scope of the statutory provisions.
If you have a warranty claim, please contact the point of sale.
Correct disposal of this product
(Electrical waste).
(Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its documentation indicates that it
should not be disposed of with other household waste at the end of its working
life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this device from other types of
waste. Recycle the device responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they pur- chased this
product, or their local government offi ce, for details of where and how they
can take this device for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial waste for disposal.
Hager SA herewith declares that
the Berker push-button
meets Directive 2014/53/EU.
The complete text of the EU declaration of conformity is available at
www.hager.com.
Berker GmbH & Co. KG
Zum Gunterstal
66440 Blieskastel/Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>