etac CloverFoot Foot Positioning Aid Instruction Manual
- October 30, 2023
- Etac
Table of Contents
Clover Foot
Instruction for use
IMM1056_IFU.Version8.2020-09-16
immedia by Ertac
CloverFoot Foot Positioning Aid
See www.etac.com
General
Thank you for choosing an Etac product.
To avoid accidents and injury when moving and handling the products, please
read this manual carefully.
The person described as “the user” in this “Instruction for Use” is the person
who is lying or sitting on the product. The carers are the people who
manoeuvre the product.
This symbol appears alongside the text in the manual. It draws the reader’s
attention to points at which there may be a risk to the health and safety of
the user or carer.
These products comply with the standards applicable for Class 1 products in
the Medical Device Regulation (EU) 2017/745 on medical devices.
At Etac we strive to continually improve our products and therefore we reserve
the right to make changes to products without prior warning. All measurements
given on illustrations and similar material are for guidance only and Etac
cannot be held liable for errors and defects.
The information given in this manual, including recommendations, combinations
and sizing, does not apply to special orders and modifications. If the
customer makes adjustments, repairs or uses combinations not predetermined by
Etac, the Etac CE certification and Etac warranty will not be valid. If in
doubt, please contact Etac.
Warranty: Two-year warranty on material and manufacturing defects,
provided that the product is used correctly.
Expected lifetime: The device has an expected service life of 1 to 2
years under normal use. The service life of the device varies depending on
usage frequency, loads and how often and how it is washed.
For further information on the Etac Patient handling, see
www.etac.com.
In case of an adverse event occurred in relation to the device, incidents
should be reported to your local dealer and the national competent authority
in a timely manner. The local dealer will forward information to manufacturer.
Symbols in general
| Washing
---|---
| Do not bleach
| Tumbledry
| Iron
| Do not dryclean
| Disinfect / Wipe off
| Never leave on the floor
| Risk of sliding down
| Keep out of the sun
| Read the user manual
| Warning
| Production year, month and day
| Batch no./Lot no.
| User mass limit = maximum rated load
| The product can be scrapped according to national regulations
| Manufacturer
****| CE -certification
| Keep dry
| Non sterile
| Article number
Intended use
CloverFoot is a footstool. It supports the user’s feet when the bed,
wheelchair or similar seat is not height-adjustable.
Intended environment
Acute care, Long-term care, Home care
Practical handling
Positioning
CloverFoot can be positioned where it is best for the individual user.
Use
The user will feel more secure when his/her feet are in contact with the
floor, or, in this case, with the CloverFoot device.
Notice
Special features
Always check the product before use and after washing.
Never use a defective product. If the product shows signs of wear-and-tear, it
must be scrapped.
Read these instructions carefully.
It is important that carers receive instruction in manual handling. Etac
offers advice and training for carers. For further information, contact Etac.
Always use the correct manual handling techniques.
Encourage the user to assist where possible.
To ensure that the user feels safe and that every manual handling is smooth,
always plan the manual handling in advance.
Never leave the product on the floor after use.
Always conduct a risk assessment, and ensure that the assistive product can be
used for the individual user and, in combination with other devices, that it
is safe for the user and carers.
If in any doubt – please contact Etac.
Material and cleaning
Material:
Plastazote LD-45
The product should be checked regularly, preferably each time it is used, and
especially after washing.
Check that there is no damage to the product.
Never try to repair a product yourself.
Never use a defective product.
Washing instructions:
This product can be wiped off with soapy water or cleaned with a solvent-free
cleaning agent with a pH level between 5-9, or a 70% disinfection solution.
Products and accessories
| Article no. | Product Description | Size (mm) |
|---|---|---|
| IM2001 | CloverFoot | W380xL320 |
Service information
Inspection
First inspection:
- Is the packaging intact?
- Read the label on the packaging and check the article no. and product description
- Check that Short Instruction is enclosed – updated User Manual/Instruction for use can be downloaded from www.etac.com or contact your Etac
- Customer Service or the local dealer.
- Check the label on the product – does it include article no., product description, lot/batch no., cleaning instructions and supplier name?
Periodic Inspection:
- Make sure that your Manual transfer system always is in a perfect condition.
- After wash – always check materials, stitching, handles, buckles.
- If the product shows signs of wear and tear, it must be removed from service immediately.
Visual inspection/Check the product:
Ensure that the materials, seams, stitching, handles, buckles are
intact/faultless.
Mechanical load or stress/Test handles:
Draw hard in the handles in opposite directions and control the material,
seams and stitching.
Test buckles:
Lock the buckle and draw in opposite directions, control the buckle and the
stitching.
Stability test:
Try to bend the product verify that it feels firm, stable and solid.
Test low/high friction:
Place the product on a firm surface or a bed, place your hands on the material
and test the friction by pushing your hands down into the
product.
Low friction – slides effortlessly High friction – no sliding/moving
Check:
Manual transfer aids with handles, straps and buckles:
Manual transfer aids with for sitting and lying transfer and with high or low friction:
Production year, month and day
The product can be scrapped in accordance with national regulations
Read the user manual