VEIKOUS PG0301-10 Metal Storage Shed Instruction Manual
- October 30, 2023
- VEIKOUS
Table of Contents
VEIKOUS PG0301-10 Metal Storage Shed
8X8 Metal Garden Shed
The 8X8 Metal Garden Shed is a sturdy and durable outdoor storage solution. The product comes in two separate boxes for easy assembly and transportation. Safety precautions must be followed at all times during the construction of the building.
Safety Precautions
- Wear work gloves, eye protection, and long sleeves when handling the building’s sharp-edged pieces.
- Be familiar with the operation of all power tools used in the assembly.
- Keep children and pets away from the worksite until the building is fully assembled.
- Do not attempt to assemble the building on a windy day or before double-checking that all parts and hardware are available.
- Never concentrate weight on the roof of the building.
Assembly Tips & Tools
- Choose a dry and calm day to install the building.
- Two or more people are required to assemble the building for faster and safer assembly.
- Basic tools and materials needed for assembly include anchors, base materials, and panel screws.
Site Selection & Preparation
Before assembling the building, select a level area with good drainage for
the best location. Ensure that there is enough space at the entrance for the
doors to open completely and outside the building to fasten panel screws from
the outside.
Accessories List
- A3
Minimum
You will receive two separate boxes for this product to be fully assembled.
Please make sure all boxes arrived in good condition before assembling. It
happens sometimes when boxes arrive separately due to postponed carrier’s
shipping, and your patience is really appreciated! You can also reach out to
us at any time at customer service@ veikous.com for any questions!
PLAN AHEAD
Before beginning installation, check local building codes regarding footings,
location and other requirements. Study and understand this instruction.
Important information and helpful tips will make your installation easier and
more enjoyable.
Tools and Materials: There are some basic tools and materials you will need for the installation. Decide which method of anchoring and the type of foundation you wish to use in order to form a complete list of the materials you will need.
BEFORE YOU BEGIN
Assembly Instruction: Instructions are supplied in this manual and contain all appropriate information for your installation. Review all instructions before you begin, and during assembly, follow the step sequence carefully for correct results.
Parts List: Check to be sure that you have all the necessary parts and
quantities in your package. These are packaged within the carton. Note that
extra fasteners have been
supplied for your convenience.
Explosion Diagram: All parts except screws and bolts are shown in this diagram, review all parts before you begin. Familiarize yourself with the hardware and fasteners for easier use during installation.
SAFETY PRECAUTIONS
Safety precautions MUST be followed at all times throughout the construction of your building!
Care must be taken when handling various pieces of your building since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building.
Keep children and pets away from the worksite during construction and until the building is completely assembled. This will help avoid distractions and any accidents which may occur.
NEVER concentrate your weight on the roof of the building. When using a step ladder make sure that it is fully open and on even ground before climbing on it.
Practice caution with the tools being used in the assembly of this building. Be especially familiar with the operation of all power tools.
Do NOT attempt to assemble your building on a windy day. The large panels can
catch the wind like a “sail”, causing them to be
and unsafe.
Do NOT attempt to assemble your building before double checking that you have
all the parts indicated in the parts lists as well as all hardware Any
building left partially assembled may be seriously damaged by even light
winds.
ASSEMBLY TIPS & TOOLS
Watch the Weather Closely: Be sure the day you choose to install your building is dry and calm. Do NOT attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
Use Teamwork: Two or more people are required to assemble your building. One person can hold the parts or panels in place while the other person fastens them together and handles the tools. This makes the process of assembling your building faster and safer.
Tools and Materials: Here is a list of some basic tools and materials you will need to assemble your building. Decide which method of anchoring and the type of base you will use to make a complete list of the materials you will need.
- Work Gloves
- Safety Glasses
- Step Ladder
- No. 2 Phillips Screwdriver (Magnetic Tip Preferred)
- Utility Knife or Scissors
- Pliers Carpenter’s Level
- Tape Measure
- Power Drill (Cordless, Variable Speed)
- Nut Driver or Wrench
- Square
- String (for squaring the frame)
- Awl (to align holes)
- Lumber and/or Concrete
- Hammer and Nails
- Spade or Shovel
- Hand Saw or Power Saw
How to Select and Prepare Your Building Site:
Before you start to assemble your building, you will want to decide on a good
location. The best location is a level area with good drainage.
- Allow enough working space so it is not difficult to move parts into position for assembly. Be sure there will be enough space at the entrance for the doors to completely open. Also, there needs to be enough space outside the building to be able to fasten the panel screws from the outside.
- Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
Dimension
Tools Required
Hardware accessories
Assembly Procedure
- Step1:Front Floor Frame Assembly
- Step2:Back Floor Frame Assembly
- Step3:Side Floor Frame Assembly
- Step4-1:Connect Floor Frame
- Step4-2:Connect Floor Frame
- Step5-1:Corner Panel Assembly
- Step5-2:Corner Panel Assembly
- Step5-3:Corner Panel Assembly
- Step5-4:Corner Panel Assembly
- Step6-1:Wall Frame Front Assembly
- Step6-2:Front Wall Frame Assembly
- Step6-3:Back Wall Frame Assembly
- Step6-4:Back Wall Frame Assembly
- Step7-1:Side Wall Frame Assembly
- Step7-2:Side Wall Frame Assembly
- Step8:Left Wall Panel Assembly
- Step9:Right Wall Assembly
- Step10:Back Wall Assembly
- Step11:Front Wall Panel Assembly
- Step12:Door Jamp Assembly
Make sure the wall panels on BOTH sides are fully covered and tightly fixed with door jamps (i.e. ULA & UR1)with no gap before installing the door panels. Otherwise the door may not work as normal.
- Step13-1:Gable Connection
- Step13-2:Gable Assembly
- Step14-1:Middle Roof Frame Connection
- Step14-2:Middle Roof Frame Assembly
- Step15-1:Side Roof Frame Connection
- Step15-2:Side Roof Frame Assembly
- Step16:Left Roof Panel Assembly
- Step17:Right Roof Panel Assembly
- Step18:Fascia Trim Assembly
- Step19:Ridge Cap Assembly
- Step20:Ridge Plastic Cap Assembly
- Step21:Side Fascia Trim Assembly
- Step22:Corner Plastic Cap Assembly
- Step23-1:Left Door Assembly
- Step23-2:Left Door Assembly
- Step23-3:Left Door Assembly
-
Step23-4:Left Door Assembly
-
Step23-5:Left Door Assembly
-
Step24:Right Door Assembly
- Step24-1:Right Door Assembly
- Step24-2:Right Door Assembly
- Step24-3:Right Door Assembly
Screws may cause hurt with sharp heads. Make sure to COVER all of them with plastic end caps to prevent potential injury.
For better experience Please visit our website WWW.VEIKOUS.COM