blink Series 4 Home EV Charger Instruction Manual

October 30, 2023
blink

blink Series 4 Home EV Charger Instruction Manual
blink Series 4 Home EV Charger

Series 4 – Home EV Charging Station

Home EV Charging Station

Warnings

WARNINGS
Please read the full document before using this Blink charger. While working with electrical devices please follow basic electrical safety procedures.

Do not try to install this charger while the breaker is still powered on.

Do not try to install this charger near flammable or explosive materials.

Do not try to operate this charger if there are any signs of physical damage, i.e., cracks, corrosion, or exposed wiring.

Do not try to modify this charger in any way not listed in this guide.

Do not try to resolve any issues with the charger that have not been outlined in the troubleshooting section of this guide.

Do not allow an unlicensed individual to wire this charger during the installation process.

Do not insert any finger or any other foreign object into the connector of this charger.

If the user of this device has any medically implanted device, please contact the medical device manufacturer to discuss how charging may affect the medical device before attempting to use this charger.

Follow all instructions in this guide during the installation of this device to avoid any additional complications.

Safety & Compliance

This document provides instructions to install the Blink charger and should not be used for any other product. This product must be installed in accordance with the National Electrical Code (NEC), the Canadian Electrical Code (CEC), or any applicable local code.

Review this manual and consult a licensed contractor and/or electrician before installation to ensure compliance with local building practices, climate conditions, safety standards, and state and local codes.

There are 2 options for installation:

  1. Option 1: Use the NEMA plug included with the charger
  2. Option 2: Hardwired charger should be installed by a licensed contractor/electrician and inspected by a qualified installer prior to initial use. Under no circumstances will compliance with the information in this manual relieve the user of responsibility to comply with all applicable codes and safety standards. This document describes the most common installation and mounting methods. Contact Blink where it is not possible to perform an installation using the procedures provided in this document.
    Blink is not responsible for damages that may occur or result from installations that are not described in this document. Please read and understand instructions before attempting to unpack, install, operate, or maintain this equipment. Study the charger and its mechanism carefully before attempting to operate it on an energized circuit. All possible contingencies that may arise during installation, operation, or maintenance, and all details and variations of this equipment do not purport to be covered by these instructions. If further information is desired by the purchaser regarding a particular  installation, operation, or maintenance of particular equipment, contact Blink.

General
The Blink charger is grounded through a dedicated conductor to the ground connection at the power distribution panel.

Statements
Reasonable effort has been made to ensure that the specifications and other information in this manual are accurate and complete at the time of publication. However, specifications and other information in this manual are subject to change at any time without prior notice. Use of the Blink charger in a manner not intended or any modification not approved by the manufacturer will void the limited warranty. Other than the limited warranty, Blink products are provided “AS IS,” and Blink and its distributors expressly disclaim all implied warranties, including any warranty of design, merchantability, and fitness for a particular purposes and non- infringement, to the maximum extent permitted by law.

IN NO EVENT SHALL BLINK CHARGING OR ITS AUTHORIZED DISTRIBUTORS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST DATA, LOSS OF USE, COST OF COVER, OR LOSS OR DAMAGE TO THE BLINK CHARGER ARISING OUT OF OR RELATING TO THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF BLINK CHARGING OR ITS AUTHORIZED DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

FCC Statement
This equipment has been tested and found

to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

For questions, please contact Blink:

Electrical Requirements

Wiring Color Code
Connect the charger to a single phase 120/240 volt, bonded neutral power source. All wire must be sized in accordance with the National Electric Code.
Wiring Color Code

Wiring Diagram
Electric vehicle charging stations must be equipped with an internal Ground Monitor/Interrupter circuit (GMI circuit). For the GMI circuit to function, a reference to ground must be made through a main bonding jumper or system bonding jumper (located where the neutral connection is established and bonded to ground). Without the neutral to ground connection, GMI protection is not possible, and the charger will be inoperable.

If you have an electrical system without a neutral you must upgrade your electrical service from the utility or provide a separately derived system to effectively power and protect the electric vehicle charger.

Wiring to System
S4 240v Supply
Wiring to System

Current Limit| 2-Pole Breaker Size| NEMA 14-50 Plug| Hardwired
---|---|---|---
16 AMPS (default setting)| 20 AMP| YES| YES
24 AMPS| 30 AMP| YES| YES
32 AMPS| 40 AMP| YES| YES
40 AMPS| 50 AMP| YES| YES
48 AMPS| 60 AMP| NO| YES
50 AMPS| 70 AMP| NO| YES

Parts List

Materials Included
Materials Included 

Allen Wrench and Mounting Hardware

Tools Needed

  • Stud finder
  • Level
  • Marker
  • Drill
  • Measuring tape

Materials Needed

  • 3/4“ Liquid Tight Flexible Metal Conduit – Hardwired Version Only
  • 3/4“ Liquid Tight Flexible Metal Conduit Connector – Hardwired Version Only

Installation

Site Selection
The charger should be installed in a location suitable for the 25-foot output cable to extend to the electric vehicle’s charging port and which allows sufficient space for output cable storage in the cable hanger. The top of the wall mount bracket is recommended to be installed at a height of 50 inches above the finished floor (check local codes).

If installing the NEMA 14-50 plug version, ensure the charger location can accommodate a NEMA 14-50 receptacle. The NEMA 14-50 receptacle should be located no less than 24-26 inches from the ground. Consideration should be made to the NEMA 14-50 receptacle orientation (ground terminal in the upward ‘12 o’clock position’ or downward ‘6 o’clock position’). The NEMA 14-50 receptacle orientation will determine the NEMA 14-50 input cord’s installation aesthetics.

Ensure the height of the wall mount bracket and the NEMA 14-50 receptacle are coordinated so the NEMA 1450 plug seats into the NEMA 14-50 receptacle without cable tension or stress. If installing the hardwired version, ensure that the selected charger location is within reach of the site rated junction box using the supplied 3 feet of manufactured cable.
Installation

Wall Preparation
Wall Preparation 

  1. Locate and remove the top mounting screw from the charger using the supplied Allen wrench.
  2. Remove the wall mount bracket from the charger by applying downward pressure on the wall mount bracket until the charger mounting screws unseat from the wall mount bracket keyhole slots.
  3. Store the charger and mounting screw in a safe place to avoid damage or loss.
  4. At the selected location, mark the center of the stud and place the wall-mount bracket on the wall.
  5. Using a level, ensure the wall-mount bracket is in an upright level position. Align center mounting holes with the center of the stud and mark the wall- mounting screws holes.
  6. Use mounting holes to secure the bracket to the wall using appropriate site- specific fasteners.

Wall Mounting (NEMA 14-50 Version)
Wall Mounting

  1. Locate the 3 mounting screws on the rear of the charger. Position them into the corresponding keyhole slots on the wall mount bracket. Slide downward until fully seated.
  2. Reinstall the top mounting screw using the supplied Allen wrench to secure the charger. The charger should feel secure after it is fully seated. If the charger can be easily moved then remove the charger, slightly tighten the three mounting screws on the rear of the charger and replace the charger on the Bracket.
  3. Insert the NEMA 14-50 plug into the NEMA 14-50 receptacle. Ensure that the plug is fully seated into the receptacle.

Wall Mounting (Hardwired Version)
The hardwired version of the Blink Series 4 EV Home Charger is manufactured with 3 feet of cable that has been listed by a Nationally Recognized Testing Laboratory (NRTL) to the appropriate UL standards for the specified ampere ratings.

Ensure that the selected charger location is within reach of the site rated junction box using the supplied 3 feet of manufactured cable. # To sufficiently attach and tighten the 3/4” Liquid Tight Flexible Metal Conduit (LFMC) to the charger, the bottom plate must be removed. Place the charger face down on a safe surface to avoid damage. Grasp the outside of the charger with both hands, position thumbs on the inner edge of the protective lower cover and apply downward pressure on the cover to unseat it from the charging station. Store protective cover in a safe place to avoid damage or loss.

  1. Measure and cut 3/4” LFMC to sufficient length between the charger and site rated junction box. Attach and tighten the 3/4“ LFMC to the charger using the manufacturer-supplied 3/4“ LFMC connector. Reinstall the protective cover.
  2. Locate the 3 mounting screws on the rear of the charger. Position them into the corresponding keyhole slots on the wall mount bracket. Slide downward until fully seated.
  3. Reinstall the top mounting screw using the supplied Allen wrench to secure the charger. The charger should feel secure after it is fully seated. If the charger can be easily moved then remove the charger, slightly tighten the 3 mounting screws on the rear of the charger and replace the charger on the bracket.
  4. Attach and tighten the 3/4“ LFMC to the site rated junction box. Connect the supplied black and red conductors to the 240-volt supply (ungrounded) conductors, and the supplied green conductor to the grounding conductor.

Install Blink Series 4 EV Home Charger in accordance with all State, Local, and National Electric Codes.
Wall Mounting

Configuration

Powering Up the Charger
After you have installed the Blink Series 4 EV Home Charger, turn on the power at the breaker. Allow up to 3 minutes for the charger to fully power on. The charger is ready to use when the LED is a steady blue color and icons are visible on the screen. If the charger does not power on, contact your electrician to ensure correct electrical installation. The charger may now be connected to a vehicle to start charging. Please note the following default settings, which may be changed by configuring the charger.

  • Power level is set to 16 amps
  • Unlocked
  • No schedule

Appropriate Amperage Setting
The charger may be configured to charge a range of amperage levels. It is essential not to select a level that is greater than your circuit breaker is rated for. Other factors, such as the electrical capacity of your panel and wiring size, may need to be considered. Please consult with a qualified electrician if in doubt.
The tables below provide guidance on the amperage level to configure on the charger based on the circuit rating.

CIRCUIT RATING NEMA INSTALLATION HARDWIRED INSTALLATION
70A N/A 50A
60A N/A 48A
50A 40A 40A
40A 32A 32A
30A 24A 24A
20A 16A 16A

Configuring the Charger
The charger may be configured to provide the optimal power level and, optionally, connect the charger to your home Wi-Fi network. Connecting the charger to Wi-Fi will enable additional features and is recommended if Wi-Fi is available at the installed location.

Connecting to the Blink Mobile App

  • Download the Blink mobile application to your smartphone.
  • Open the app, click on My Account, and log in (create an account if you do not have one).

Note: The Blink mobile app provides access to all public Blink charging stations in addition to the Series 4 EV Home Charger.

App Download
QR Code

Basic Configuration
To configure the charger, perform the following steps in the Blink mobile app:

  1. Access the Home Charger menu and follow the instructions to add a charger.
  • Initiate the pairing process on the charger by inserting the supplied Allen wrench into the small opening where the vehicle connector attaches to the charger and briefly pressing the recessed button for less than 2 seconds. See diagram below.
  • If connecting to an available WiFi network, select the network and provide the password.

The charger will now be listed in the Home Charger section of the mobile application.
Connecting

Advanced Configuration
Advanced features may be configured if the charger is connected to WiFi.
To perform this configuration, click on the settings icon for your charger in the Home Charger section of the mobile application. Select one of the following modes:

  • Unlocked (default): The charger will start charging immediately after an electric vehicle is connected.
  • Locked: The charger requires authorization (using the mobile app) to begin charging once an electric vehicle is connected.
  • Scheduled: The charger will only charge the connected electric vehicle during the specified schedule.

Operation

Charging Your Vehicle
To start a charging session, connect the vehicle to the charger.

  • Unlocked mode – charging will begin immediately.
  • Locked mode – charging will begin once authorization is provided using the mobile app. Press the Start Charging button in the Home Charger section.
  • Scheduled mode – charging will begin automatically during the specified schedule.

Stopping a Charge
To stop a charging session, disconnect the vehicle from the charger.

LED Lights
The LED light on the station may display the following colors:

COLOR MEANING
Steady Blue No vehicle is connected. Plug in to start a charge.
Flashing cyan Vehicle connected but not charging. The charger is waiting for

authorization (from the mobile app) or the schedule.
Flashing green| Vehicle connected and charging in progress.
Steady green| Vehicle connected and charging is complete.
Steady red| Charger error. Please refer to the troubleshooting guide.

On-screen Icons
The charger may show the following icons on the screen:

ICON| MEANING|
---|---|---
Icon| No vehicle Is connected. Plug in to start a charge.|
Icon| The vehicle is charging.|
Avehicle has been plugged-in to the charger.|
Icon
The charger has paused the chargim session. This could Indicate the charger is waiting for a schedule to begin or the session has been stopped by the mottle application.|
Icon| The vehicle has paused the charging session. This could indicate that a schedule has been configtred in the vehide.|
Icon
The vehicle battery is full.|
Icon
There is a charging error reported by the vehicle.|
Icon| There is en error reported by the station.|
Icon| Access Mode: Unlocked and Locked.|
| Schedule mode: Schedule is oft or on.|
| Connected mode: Staeon Is disconnected or connected to 1MM.|
| Reserved for future use|
| There is an error connecting to WiFi.|

Troubleshooting and Maintenance

Troubleshooting

ISSUE POSSIBLE CAUSE RESOLUTION
No light or screen icons are displayed. The charger has no power. Ensure the

breaker is powered on. Ensure the charger is plugged-in or correctly hardwired.
The charger is powered-on but the connected vehicle is not charging.| The vehicle battery is already full.| Reconnect the vehicle when the battery requires charging.
A schedule is configured on the vehicle.| Wait for the scheduled start time. To start charging immediately, clear the schedule from the vehicle.
A schedule is configured on the charger| Wait for the scheduled start time. To start charging immediately, switch the mode to Locked or Unlocked using the mobile app.
Locked mode is enabled.| Use the mobile app to start charging.
The charger is locked and starting the charging session using the mobile app is not workingORChanges made in the mobile application are not reflected in the charger.| The charger has lost connection to home WiFi.| Check that your home WiFi is enabled and has sufficient signal strength to maintain a good connection with the charger.
The home WiFi network name or password has changed.| Use the mobile app to repeat the configuration process using the new WiFi network and password.

Other Troubleshooting Steps
If the above table does not resolve the issue, it is possible that the following steps may be attempted:

  • Power cycle: Turn power off at the breaker, wait 20 seconds, and then restore power. Allow up to 3 minutes for the charger to complete the power-on process.
  • Reconnect the charger to your account: Delete the charger from your mobile application in the settings section of the charger. Then repeat the configuration process described above.
  • Factory reset: Delete the charger from your mobile application in the settings section of the charger. Perform a factory reset by using the supplied Allen wrench to press the recessed button and hold it down for 15 seconds before releasing. Allow 3 minutes for the process to complete. Then repeat the configuration process described above.

Maintenance

  • Clean the charger by wiping it with a dry or slightly damp cloth.
  • Do not exert too much pressure on the charger during cleaning.
  • Do not open the device to clean it.
  • Do not use a vacuum cleaner.

Updating Charger Firmware
Updated firmware may be made available to add additional features or correct reported issues. The mobile app can be used to check for new firmware and apply it to the charger.

Removing the Charger from your Account
If you no longer wish to access the charger from the mobile application, it can be deleted in the settings section of the mobile application.

Factory Reset
To remove your account information from the charger, perform a factory reset:

  • Delete the charger from your mobile application in the settings section of the charger.
  • Use the supplied Allen wrench to press the recessed button in the small opening where the vehicle connector attaches to the charger and hold it down for 15 seconds before releasing. Allow 3 minutes for the process to complete.

blink logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals