23ZERO SABER X Hardshell Roof Top Tent User Manual

23ZERO SABER X Hardshell Roof Top Tent

Safety & Warnings

DO NOT CLIMB ON LADDER UNTIL CORRECT ANGLE IS ACHIEVED 23Zero – The wholesaler / manufacturer shall not be liable for special, indirect incidental or consequential damages.

Hardware & Accessories

The Saber X Hardshell roof top tent includes a mounting kit with everything required to mount the roof top tent to most roof racks. Some platform style roof racks have platforms which are wider than the supplied mounting plate. 23ZERO have wider mounting plates available for this scenario. Please visit www.23zero.com.au.

Fitting to roof rack

Follow the instructions provided with the mounting kit to fit the roof top tent to your roof rack.

Roof bars

If you do not have a roof rack, you can use roof bars to fit the roof top tent to your vehicle. Refer to the mounting rail dimensions below to ensure a proper fit.

Ladder adjustment

Adjust the ladder height as needed using the locking buttons. Make sure that the ladder is locked in place before climbing on it.

Opening & Set up

When setting up the roof top tent for the first time, check for any aluminium swarf inside the tent and remove it. Follow the instructions provided with the tent to open and set it up properly.

Closing & Storage

Follow the instructions provided with the tent to properly close and store it.

Warranty

The 23 ZERO Roof Top Tent comes with a 2-year warranty.

Mounting rail dimensions

Refer to the diagrams and dimensions provided below to ensure that your roof racks or bars are compatible with the mounting rails of the roof top tent.

Thank you for purchasing a 23 ZERO Roof Top Tent

• Congratulations on the purchase of 23ZERO’s SABER X Hardshell Roof Top Tent. We strive to provide you with the ultimate camping experience. The SABER X Tent mounts directly to a roof rack or aftermarket roof bars. It opens and is fully setup in seconds. As well as our innovative LST fabric, this hardshell tent is made with durable materials and high-quality fabrics that provide excellent water and wind protection.
• Most of the components have been pre-assembled with the exception of ladder brackets, awning stay pole brackets and roof bars. Depending on vehicle set up and choice of entry points, these components can be repositioned to suit.
• Note: During set up and first use, some aluminium swarf may be present inside the roof top tent. We make every possible attempt to expel all aluminium swarf, however, with vibrations caused by logistics some residual may dislodge and reappear. It is advised to remove and clean these during first set up.
  PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLING

IMPORTANT
Before installing your 23Zero Roof Top Tent please ensure you are aware and understand the following:

• Your vehicle’s maximum roof load rating.

• Your roof rack’s maximum load rating including off-road capacity.

• The maximum amount of weight you can safely add to a vehicle’s roof / cargo area differs according to make and type of vehicle including aftermarket additions such as roof racks / bars.
  Note: Roof rack off-road limits are immensely different to normal road use load ratings. If in doubt, please contact your vehicle manufacturer and roof rack manufacturer / supplier for specified loading capacity of your vehicle and roof rack.

• Not all factory roof racks or aftermarket roof bars can safely accommodate roof top tent models. The responsibility of fitting this roof top tent to rated roof racks or roof bars lays with the purchaser.

Safety & Warnings

• Improper installation or use of the Saber X roof top tent may result in serious injury or death. Follow these installation instructions carefully to ensure proper installation to vehicle and safe use of the roof top tent.
  Note: Alterations and / or inclusions such as roof racks and roof top tents applied to the vehicle roof may affect vehicle handling and characteristics.

• The manufacturer (23ZERO) disclaims all responsibility in case of accidents and / or damage due to installation of a roof top tent to an underrated roof rack, improper use, improper maintenance or checking the tightness of the brackets regarding the installation of the roof rack system.
  Inspections: Roof top tents have many moving parts, so maintenance checks are always advised. During trips regularly check that all nuts and bolts attaching the roof top tent to the vehicle as well as hinges and locks are tight and in good repair.
  Ladder: For your safety and protection, ensure correct placement and angle of ladder. Recommended ladder placement is a 4:1 ratio or approx. 75°.

• Ladder height may need to be adjusted depending on vehicle height, see “Ladder Adjustment”

DO NOT CLIMB ON LADDER UNTIL CORRECT ANGLE IS ACHIEVED
23Zero – The wholesaler / manufacturer shall not be liable for special, indirect incidental or consequential damages.

Hardware & Accessories

The Saber X Hardshell roof top tent includes a mounting kit with everything required to mount the roof top tent to most roof racks.

Note: Some platform style roof racks have platforms which are wider than the supplied mounting plate. 23ZERO have wider mounting plates available for this scenario.
Please visit www.23zero.com.au.

Fitting to roof rack

• The Saber X roof top tent must be fitted to roof racks with hinges facing forward. Clamp 4 corners using 8 x M8 bolts, 8 slide plates & 4 x mounting saddles supplied.

• Lift roof top tent on top of the vehicle’s roof rack (minimum 4-person lift).
  Important: Ensure the Saber X is closed during fitment..

• Fit 8 x M8 bolts into 8 x slide plates and slide each into bottom mounting rail. Position these so there are 2 sets of bolts in each corner of the tent. Lift / tilt the roof top tent to allow the inner bolts to cross over onto the inside of the roof bars, See pic below. (mounting plate replaced by mounting saddle)

• Inspect the position of the roof top tent to ensure it will open in the desired position.
  • Note: It is recommended the rear of the tent is flush with the back of the vehicle to allow correct ladder angle. Place a mounting saddle under the roof bar whilst locating the bolts, insert washer and hand tighten Nylok nut. Repeat for all 4 corners. Double check the tent’s position as desired and tighten all nuts securely with 13mm spanner. Insert end caps into the ends of the mounting rails, this may require light taps from a hammer.
  • Inspections: Roof top tents have many moving parts so maintenance checks are always advised. During trips regularly check that all the above fixings are tight and in good repair.

Roof bars

Note: The roof bars supplied with the Saber X roof top tent are not designed to carry significant loads. A maximum of 20kg can be carried on top of the Saber X providing this weight is spread evenly amongst the 2 bars.

• When adding additional weight to the top of the Saber X consideration must be given to the overall weight rating capacity of your vehicle’s roof and roof rack.
• Please ensure you are aware and understand the following:
  • Your vehicle’s maximum roof load rating.
  • Your roof rack’s maximum load rating including off-road capacity.
• The maximum amount of weight you can safely add to a vehicle’s roof / cargo area differs according to make and type of vehicle including aftermarket additions such as roof racks / bars.
  Important: Before each trip please check that all roof bar and bracket fixings are tight and in good order before adding load.

Ladder adjustment

• For your safety and protection, ensure correct placement and angle of ladder. See diagrams below. Recommended ladder placement is a 4:1 ratio or approx. 70° to 75°.
  NOTE: Under no circumstances should anyone be inside the roof top tent if the ladder is not locked and secured at the correct angle.

• The ladder may need to be adjusted to achieve the correct angle depending on the height of your setup. If shortening is required, the adjustment must be done from the top.

• Ensure the ladder is fully extended and all rungs are locked in place. Press the first set of locking buttons (second rung from the top) and allow the ladder to compress until a gap of approx. 85mm is achieved between rung 1 & 2.
  Note: The ladder will only lock in the downward position.

• Swing in the bottom of the ladder until it supports the weight of the roof top tent. If the angle of the ladder is between 70° and 75°, the adjustment is complete.

• If further shortening is required press the second set of locking buttons (third rung from the top). This will close the 85mm gap until rung 1 & 2 are now touching. Swing in the bottom of the ladder until it supports the weight of the roof top tent. If the angle of the ladder is between 70° and 75°, this adjustment is complete.

NOTE: When height adjusted, the ladder will only lock in the downward position.

• If further adjustment is required, repeat the above steps by continuing the sequence by depressing the next set of locking buttons.

Opening & Set up

Once the Saber X is fixed securely to the vehicle’s roof rack and the ladder is locked and angled correctly, climb the ladder, release the locks front and rear of tent and lift until the gas struts take over. Once open, lower the perimeter shock cord and hook this to both front corners of the baseboard. Locate the canopy stay poles and fit each of these into their brackets with the hook end facing outward. Flex each pole and insert the hook ends into the eyelets on the corners of the canopy. Unzip entry door and enter the roof top tent. The tent is now ready for use.

Closing & Storage

• Sleeping bags or blankets can be stowed inside the Saber X if laid out flat.

• Additional mattresses and/or toppers must not be left in tent when closing. Not only do these make closing the tent difficult but they will put excessive pressure on X frame and struts which may lead to failures and damage. This damage is distinguishable and is not covered by warranty.

• An external perimeter shock cord is included with your Saber X hardshell roof top tent. These assist in reducing the canvas from billowing during pack up. Exit the tent, remove the canopy tension poles and lift the perimeter shock cord halfway up the canvas ensuring it goes over the canopy canvas as well. The tent is now ready to close.
  Tip: Leave the side windows open halfway open to allow internal air to escape while closing the tent.

• As the Saber X is closing, tuck the canvas inside so none is caught between the sealing rubbers on the roof lid and baseboard. Engage the locks. Unhook the ladder, retract and stow in carry bag.
  Caution: Avoid closing / storing tent wet. If conditions dictate that you do, open and dry out as soon as possible to avoid moisture damage.

2 Year Warranty

23ZERO will replace or repair any product at its discretion that is subject to faulty manufacturing or workmanship including materials.

Exclusions
The above warranty is limited to manufacturing and materials defects. Not including damage caused by misuse or abuse, wear and tear, condensation, extreme weather, accidents, incorrect set up, damage caused by mould, insects, animals or children. This also excludes broken poles and damage caused by a jammed, snagged zipper or excessive force applied to zipper causing failure.

Consumer rights

• Our goods come with guarantees that cannot be excluded under Australian law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure.
• Due to our policy of continual product development, the specifications, colours and features may vary.

Making a claim
To make a claim in relation to the above manufacturers warranty please ensure you retain your sales receipt of purchase. Please contact us stating the nature of your claim and we will be in touch with you shortly. If you require additional assistance, please phone 03 9547 4691 to dis-cuss and arrange your claim. Product subject to warranty will be sent to 23ZERO Australia, 32b Eileen Rd. Clayton South, Victoria 3169. All freight costs associated with return of product for assessment is payable by consumer.

Mounting rail dimensions

The diagrams and dimensions below will assist in preparing roof racks and roof bars for fitment.

ABOUT COMPANY

• 23ZERO AUSTRALIA
• www.23zero.com.au
• 328 Eileen Rd Clayton South, VIC 3169
• sales@23zero.com.au

References

• 23Zero Australia | Where your Adventure Begins - Roof Top Tents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>