STANLEY NB08PT-18 Blind Nut Tool Battery Power Tool Instruction Manual

Accessories Manual
NB08PT-18 Blind nut tool
Battery Power Tool

NB08PT-18 Blind Nut Tool Battery Power Tool

Original Instruction
©2021 Stanley Black & Decker
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically or mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information provided is based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening pursues a policy of continuous product improvement and therefore the products may be subject to change. The information provided is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered Fastening cannot be held liable for any damage resulting from deviations from the original specifications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening will not  accept any liability for damage resulting from activities carried out by third parties. The working names, trade names, registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free, pursuant to the legislation with respect to the protection of trademarks.
STANLEY Engineered Fastening policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice.
Nose Assemblies
Nose equipment varies according to the blind insert nut type being installed. Each nose assembly represents a unique set of components which can be ordered individually. Component numbers refer to the illustration below. We recommend maintaining some stock of spares as items will need regular replacement if worn. Read the Service Manual for nose assembly instructions.

MAIN COMPONENTS LIST

*for complete tool explosion and Bill of Material please see service manual

ACCESSORIES CHANGING INSTRUCTIONS

Always wear approved hearing and eye protections at all times when using installation equipment.
WARNING: Before adjusting tool, always remove the battery pack.
Mounting the mandrel and nosepiece

• Select the correct mandrel (A) and nosepiece (B) for the blind nut (K) to be installed.
• Loosen the nose housing nut (E), Remove the nose housing (D).
• Press the mandrel lock (F), Loosen and remove the mandrel (A).
• Screw the correct mandrel (A) into Spin Pull Head (H) while pressing the mandrel lock (F). Lock the mandrel (A)
• Loosen the lock nut (C) and unscrew and remove the nosepiece (B) and Lock nut (C)
• Screw the Lock nut (C) onto the correct nosepiece (B) and screw the nosepiece (B) into the nose housing (D) lightly.
• Adjust the position of the nosepiece (B) according to the blind nut (K) to be installed. The length of mandrel protruding from the top of blind nut (K) to be 00.5mm.
• Tighten the lock nut (C) by a spanner properly.

PLACING SPECIFICATIONS

NB08PT-18
M3| M4| M5| M6| M8| M10
Eurostat®| ●| ●| ●| ●| ●| ●
Thin Sheet Nester®| ●| ●| ●| ●| ●|
DK/DL| ●| ●| ●| ●| ●| ●
Euro Exert®/Exert®| ●| ●| ●| ●| ●|
High Strength Exert®| | | | ●| ●|
Squarest®| | | ●| ●| ●|
Standard Nut (Steel)| ●| ●| ●| ●| ●| ●
Standard Nut (Aluminum)| ●| ●| ●| ●| ●| ●
Standard Nut (Stainless steel)| ●| ●| ●| ●| ●|
Closed End Nut| ●| ●| ●| ●| ●|
Hexagonal Nut| ●| ●| ●| ●| ●| ●
All Hexagonal Nut| | | | ●| |
Tetra Nut| | ●| ●| ●| ●|
Knurled Nut| | ●| ●| ●| ●|
Soft Set Nut| | ●| ●| ●| |
Slit Nut| | | | ●| |
Pipe Nut| | | | ●| |
HB Bolt| | | | ●| |
HB Bolt for round pipe| | | | ●| |

Note:
Force control can be used for the following sizes only.
Aluminum M6 or more (Except for Slit Nut).
Steel M5 or more.
Stainless steel M5 or more.

MANDREL AND NOSEPIECE

WARNING: When selecting mandrel and nosepiece, always use the compatible parts. Using different parts may cause nut tightening failure or tool failure.
Note:

1. Refer Table B for Thin sheet Nester®.
2. Refer Table C for Thin head Exert®.

Table A Mandrel and Nosepiece compatible chart *：Option parts

*Table B Thin sheet Nester® compatible chart ：Option parts**

*Table C Thin head Exert® compatible chart ：Option parts**

MANDREL AND NOSEPIECE (OPTIONS)

1. Pipe Nut (Made to order)
   When fastening the pipe nut SRH-630-191-K2, install the nose assembly for the pipe nut. The mandrel used is PNT600-01-6P. Please refer to the following list for the nose assembly components for pipe nuts.
   ● SRH-630-191-K2** Nose Assembly| TNM00354**
   ---|---
   | SA Mast Housing| TNM00355
   SA Nose Housing| TNM00356
   | Nose Housing| TNM00257
   Nose Slider| PNT600-137A
   Slider Spring| AN600P-31
   Retaining Ring| AN600P-32
   Nosepiece| PNT600-02-6NP
   Lock Nut| PNT600-03
   Hexagon socket button bolt| PNT600-100
   Spacer| PNT600-138

2. Pipe HB Bolt (Made to order)
   When fastening pipe HB bolts, install the pipe HB nose assembly. Change the mandrel attached to the tool to the socket that comes with the nose assembly.
   Please refer to the following list for each nose assembly component.
   ● SRB-630-480LF-K2-180L** Nose Assembly| TNM00358**
   ---|---
   | SA Mast Housing| TNM00355
   SA Nose Housing| TNM00359
   | Nose Housing| TNM00258
   Nose Slider| TP134-080
   Slider Spring| AN600P-31
   Retaining Ring| AN600P-32
   Nosepiece| TZ024-435
   Lock nut| PNT600-03
   Button Head Cap Screw| PNT600-100
   Spacer| PNT600-138
   Socket| TNM00365

● SRB-830-480-K2-70L

3. HB Bolt (Made to order)
   When tightening HB bolts, replace the mandrel attached to the following nosepiece and tool with the following socket to make a tool for HB bolts. HB Bolt| Socket| Nosepiece
   ---|---|---
   **SPB-650R-WB***| PNT600-01-6HB-WB| PNT600-02-6HB-WB
   SPB-625-RLT| PNT600-01-6HB| PNT600-02-6HB

4. Slit Nut (Made to order) *Only can be used by Stroke control When fastening the slit nut, attach the sleeve to the outer diameter of the mandrel and replace it with the following nose piece. The mandrel used is PNT600-01-6P.
   Slit Nut| Nosepiece|
   ---|---|---
   SPH-640-SLIT| PNT600-02-64SLT-S| ENS-M6SV-S
   SPH-670-SLIT| PNT600-02-67SLT-S

5. KALEI® ST Nut (Made to order) *Only can be used by Force control When fastening the KALEI nut, please use the following adapter. Remove the standard Nosepiece and Lock-nut from Nose Housing, and attached the adapter.

● ST6-10, ST6-15

****STANLEY Engineered Fastening
4 Shelter Rock Lane
Danbury, Connecticut,
United States, 06810
Tel. 877 364 2781
Fax 800 225 5614

References

• Contact Us | STANLEY® Engineered Fastening
• Find A Fastener Distributor | STANLEY® Engineered Fastening

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>