HEATSTRIP THY2200P Intense Portable Electric Heater Owner’s Manual

HEATSTRIP THY2200P Intense Portable Electric Heater

Product Overview
The THY2200P is a high-intensity electric radiant heater with a carbon filament element. It is designed for indoor and outdoor use and comes with a black anodized alloy casing and endcaps, a powder-coated grille, and a powder- coated mild steel stand.

Specifications

Model| Power (Watts)| Current (Amps)| Dimensions (mm)| Weight (Kg)| Lead Length (mm)| Plug| Heater Type| Power Connection| Approvals| Protection Rating| Material of Construction
---|---|---|---|---|---|---|---|---|---|---|---
THY2200P| 2200| 9.2| 1068(W) x 2050(H) x 500(D)| 20| 3000| Yes| High-intensity electric radiant heater with carbon filament
element.| 230-240 Volts Nominal at 50–60 Hertz, Single Phase 3 Core
Cable 2.5mm2| AUSTRALIA/NZ| IPX5 Protection from water ingress from all directions| Heater: Black anodized alloy casing & endcaps, powder
coated grille Stand: Powder-coated mild steel

Features & Benefits

• Designed for indoor and outdoor use
• High-intensity electric radiant heater with carbon filament element
• Black anodized alloy casing and endcaps
• The powder-coated grille and mild steel stand
• IPX5 protection from water ingress from all directions

Installation Requirements
To assemble the THY2200P electric radiant heater, you will need the following hardware:

• Pan Head Screw M6 x 10mm (x9)
• Screwdriver

Parts List
The following parts are included with the THY2200P electric radiant heater:

Assembly Instructions
To assemble the THY2200P electric radiant heater, follow these steps:

1. Attach the skidpad to the bottom of the wheel.
2. Attach the fixed bracket to the base using Pan Head Screw M6 x 10mm (x2).
3. Attach the lower post to the base using a Pan Head Screw M6 x 10mm.
4. Attach the left and right side panels to the lower post and base using Pan Head Screw M6 x 10mm (x2).
5. Attach the rear panel to the side panels and lower post using a Pan Head Screw M6 x 10mm (x2).
6. Attach the heater bracket to the upper post using a Pan Head Screw M6 x 10mm.
7. Attach the upper post to the lower post using a Pan Head Screw M6 x 10mm.
8. Attach the base bracket to the electric heater using a Pan Head Screw M6 x 10mm.
9. Attach the electric heater to the upper post using a Pan Head Screw M6 x 10mm.

Maintenance and Safety
To maintain and ensure the safe operation of the THY2200P electric radiant heater, follow these guidelines:

• Use only Thermofilm replacement parts for repairs or replacement.
• Keep this instruction manual for convenient referral and for parts replacement.

Replacement Parts Warranty

If you need to obtain replacement parts for your THY2200P electric radiant heater, please contact Thermofilm Australia Pty Ltd at (03) 9562 3455 or sales@thermofilm.com.au. To ensure you receive the correct parts, please have the following information ready:

1. Model and Serial Number (see label on the heater)
2. Part Number
3. Part Description
4. Quantity of parts needed

Use of any part that is not a Thermofilm replacement part can be dangerous and void your product warranty. For repairs or replacement parts, please contact:

• Thermofilm Australia Pty Ltd
• 8 Lakeview Drive Scoresby, Victoria 3179, Australia
• Telephone: (03) 9562 3455
• 9:00am-5:00pm Mon-Fri (EST)
• Email: sales@thermofilm.com.au

To obtain the correct replacement parts for your electric radiant heater, please refer to the part numbers in this parts list. The following information is required to ensure you receive the correct parts:

1. Model and Serial Number (see label on the heater)
2. Part Number
3. Part Description
4.  Quantity of parts needed

Important: Use only Thermofilm replacement parts. The use of any part that is not a Thermofilm replacement part can be dangerous and void your product warranty. Keep this Instruction Manual for convenient referral and for parts replacement.

Specifications – Australia

MODEL| POWER (WATTS)| CURRENT (AMPS)| DIMENSIONS (mm)| WEIGHT (Kg)| LEAD LENGTH

(mm)

| PLUG
---|---|---|---|---|---|---
THY2200P| 2200| 9.2| 1068(W) x 2050(H) x 500(D)| 20| 3000| Yes
HEATER TYPE| High intensity electric radiant heater with carbon filament element.
---|---
POWER| 230-240 Volts Nominal at 50—60 Hertz, Single Phase
CONNECTION| 3 Core Cable 2.5mm2
APPROVALS| AUSTRALIA/NZ
PROTECTION RATING| IPX5 Protection from water ingress from all directions
MATERIAL OF CONSTRUCTION| Heater: Black anodized alloy casing & endcaps, powder-coated grille Stand: Powder-coated mild steel

Features & Benefits

•  The stylish, high quality portable, free-standing outdoor heater stand
• Ideal for alfresco areas, balconies, apartments & hospitality (internal & external use)
• High-Temperature Output
• All-black construction with an attractive hexagonal-shaped grille
• Instantaneous Heat
• Infrared Carbon Filament Element
• Concealed power cable ensures a sleek appearance
• Components are sub-assembled for easy DIY installation
• In-built wheels for easy portability, perfect for residential and commercial applications
• Corrosion protected even the toughest environments
• 2 years residential and 1-year commercial warranty

Tips

• If an extension lead is required, use one as short as possible, as a long lead may result in performance loss
• Locate the heater as close to the PowerPoint as possible
• This portable heater is for spot heating only. Locate as close to the area you want to heat as possible (e.g Table)
• Store under cover at all times

Heating Area

MODEL| INDOOR PROTECTED (m 2 )| OUTDOOR ENCLOSED (m 2 )| OUTDOOR EXPOSED (m 2 )
---|---|---|---
THY2200P| 14| 9| 5

Parts List of THY2200P

Parts Diagram

13

| Key| Description
---|---|---
1| Wheel
2| Skid Pad
3| Base
4| Kick Plate
5| Fixed Bracket
6| Post—Rear, Lower
7| Post—Rear, Upper
8| Post—Front, Lower
9| Post—Front, Upper
10| Side Panel / Left
11| Side Panel / Right
12| Rear Panel
13| Heater Bracket
14| Base Bracket
15| Electric Heater Model THY2200

Hardware Pack For THY2200P

Install Side Panels to Lower Post & Base

Pan Head Screw M6 x 10mm|
Pan Head Screw M6 x 10mm| | ****

Install Real panel to Side Panel & Lower Post

Pan Head Screw M6 x 10mm|
Pan Head Screw M6 x 10mm| | Install Heater Bracket to Upper Post
Pan Head Screw M6 x 10mm| | Install Upper Post to Lower Post
Screwdriver| |
Pan Head Screw M6 x 10mm| ****| Install Lower Post to Base

Hardware Diagram for THY2200P

Assembly Instructions

CAUTION: To assemble this heater, you should obtain assistance from another person when handling the larger, heavier pieces.

Joining Base

• Remove all the packing material and place it on a non-abrasive surface.
• Position the Base as shown in the diagram.
• Once the slotted holes are aligned, use 5 Pan Head screws then tighten securely with the nuts provided

Install Base Brackets

• Install two Brackets to the Base using 4 Pan Head Screws (M6x10mm), once brackets are in place tighten all the screws securely.
• Adjustable Skid Pads will be provided. Screw Skid Pads on each corner as shown in the diagram.

Note: Base brackets can be concealed if angled inwards

Install Lower Post

• Attach the Lower Post to the Base by matching the slotted holes on the Lower Post to the screws on the Base. Next, attach 3 Pan Head Screws M6x10mm, then tighten all the screws securely

CAUTION: To assemble this heater, you should obtain assistance from another person when handling the larger, heavier pieces

Install Side Panels

• Place two Side Panels onto the Base.
• Install the Left Side Panel to the Lower Post using 2 Pan Head Screws (M6x10mm). Then place the Left Side Panel to the Base matching the slotted holes. Once the slotted holes are matching, use 3 Pan Head Screws (M6x10mm) and screw securely with the Flange Nuts.
• Repeat the same procedure for the Right Side Panel, then tighten all the screws securely

Install Rear Panel

• Place and install the Rear Panel to the Lower Post using 2 Pan Head screws. (M6x10mm)
• Once the top 2 Pan Head screws are Installed, match the slotted holes on the Rear Panel to the Side Panels.
• Screw all 4 holes securely using 4 pan head screws (M6x10mm) and Flange Nuts.

Install the Heater Bracket to the Top Post

• Place the bracket head on the top post.
• Using the Bracket Head, match the slotted holes to the top post.
• Once the slotted holes are matched, use 4 pan head screws (M6x10mm), then tighten securely shown in the diagram.
• Ensure the bracket is attached in the correct direction, as per the diagram

CAUTION: To assemble this heater, you should obtain assistance from another person when handling the larger, heavier pieces.

Install Top Post to the Lower Post

• Insert and slide the top post over to the lower post connecting the stand using 8 pan head screws (M6x10mm), then tighten all screws securely.

Install the Heater to the Bracket Head attached to the Upper Post

• Using the 2 brackets, attach the brackets to the heater.
• Match the brackets to the slotted holes located on the bracket head shown in the diagram.
• Using 2 Hex nuts bolts, tighten the heater brackets to the bracket head support securely.
• Ensure the heater is centered on the post.

Tip: Tilt the stand on a chair or a solid non-abrasive surface before connecting the heater to the bracket head.

Concealing Power Cord

Place the plug into the circular hole located at the top of the upper post. The plug should drop to the bottom of the heater, and pull the cord gently from the bottom hole. This step will conceal the cord and 3-pin plug

Optional Accessory

TT-MTR-PLUG
TT-MTR-PLUG provides an easy means of remotely turning on the appliances that are normally permanently connected to a standard wall socket. An easily selected 1-hour, 2 hours, and 4 hours timer function is accessible on both the wall unit and remote. Programmable remote control unit capable of controlling multiple units.

Specification

3105, 3112, 3100

Safety

• HEATSTRIP® Intense has an IP rating of X5. This means it is protected from water ingress from all directions.
• HEATSTRIP® has undergone extensive testing both in laboratory conditions, in Thermofilm’s manufacturing facility in
• Melbourne and field trials in Australia and overseas. It is this testing that gives the purchaser the confidence of a high-quality product.
• Independent laboratory testing has confirmed Thermofilm’s full compliance with Australian and other International Standards including CE, AS/ANZ, UL/CSA
• HEATSTRIP® is Class 1 equipment and must be earthed.
• In operation, this heater is VERY HOT— do not touch any part of the heater while it is turned on.
• Do not touch any part until at least 30 minutes after it is turned off.

This appliance is not intended for use by persons (including children) with reduced physical, sensory, or intellectual capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use
of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance. Do not allow any cables, furnishings, flammable materials, or other items to come in contact with any surface of the heater. The heater needs to be installed as per the installation instructions. In case of a heater fault or damaged supply lead, the appliance should be returned to the point of purchase for return to Thermofilm for repair.

Maintenance

The HEATSTRIP® Intense is made from durable materials, however regular care and maintenance of your heater will help prolong the life of the heater. It is recommended that you clean the heater with a soft cloth, and gently wipe the surfaces of the heater with a mild detergent to remove the built-up contaminants from the environment. Then rinse all detergent off the heater. All chemicals in the atmosphere including cigarette smoke, pollution, etc. will tarnish the surface of the heater. In this case, additional cleaning and maintenance may be required. Carrying out the cleaning process at least every three months will reduce the amount of build-up and keep the Heatstrip in good condition. If the heater is in a corrosive environment eg. salt spray, we recommend that you clean your heater with a light spray of fresh water every week. After cleaning, turn the heater on for 20 minutes to dry any water residue and prevent water staining. Before cleaning or inspection activity, the heater must be switched off and cooled down completely. Do not use any abrasive materials or products to clean the heater, this includes solvents, citrus-based cleaners, or other harsh cleaning products. When handling the heater, ensure that your hands are clean or that you use clean gloves as grease or dirt can mark the surface of the heater. Do not use high-pressure water to clean heaters

Warranty Terms & Conditions

• below Warranty Terms and Conditions apply for Australia and New Zealand only. For international warranty please refer to international warranty terms and conditions.

• Thermofilm warrants to the original owner that HEATSTRIP Electric Portable Heater products will be free from defects in materials and workmanship for a period of 24 months from the date of purchase for residential applications and 12 months for commercial applications in accordance with the following warranty terms and conditions.
  Provision of this warranty is subject to

• The HEATSTRIP products must be installed in accordance with the Installation Instructions and relevant electrical standards and codes.

• The HEATSTRIP products must be maintained and cleaned according to instructions detailed in the Installation Manual.

• There is no warranty expressed or implied with regard to capacity requirements. The selection of the unit or units depends entirely upon the system design and capacities as determined by the purchaser.

• The customer has not repaired, opened or altered the product in any unauthorized manner.

• This warranty excludes damage to the product or components arising from circumstances outside the control of Thermofilm, including, but not limited to, where the product is not used for the intended purpose; where the product has
  been rectified in any way; incorrect installation; incorrect power supply; damage caused during delivery; misapplication, misuse, abuse, vandalism, lack of maintenance or accident.

• Thermofilm’s obligations under this warranty are limited to repair or replacement at Thermofilm’s factory of any components of the product which Thermofilm identifies to its satisfaction to be defective.

• Transportation charges involved in the return of the product to the Thermofilm factory (or any other location authorized in writing by Thermofilm) is the sole responsibility of the customer.

• All products are inspected and tested before despatch and are at the risk of the purchaser after the shipment from the Thermofilm factory, if not delivered by Thermofilm to destination.

• No products or components will be supplied in advance of an examination of the faulty product or components by

• Thermofilm or an authorized representative of Thermofilm.

• Thermofilm does not participate in any site-related costs or labor expenses incidental to the replacement of parts, repairing, removing, installing, servicing, transporting, or handling of parts to complete products, and assumes no liability for parts repaired or replaced without written authorization. Thermofilm shall not be liable for any default or delay in the performance of its warranty obligations caused by any circumstances beyond its control, including, but not limited to, judicial or government restrictions, strikes, fires, floods, abnormal weather conditions, and delayed supply of components.

• Should products be determined as damaged on arrival, immediately notify the transport company of the condition and have them noted on the freight documents. If damage is discovered after unpacking, demand immediate inspection by the transportation company and insist that a record of the damage is made on the freight documentation.

• The customer warrants using the product in accordance with:

• Any instructions provided to it by Thermofilm from time to time.

• All government and local regulations, including but not limited to all relevant electrical, and environmental laws and regulations governing the installation, storage, use, handling, and maintenance of the goods.

• All necessary and appropriate precautions and safety measures relating to the installation, storage, use, handling, and maintenance of goods.

• Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

• All warranty requests for repairs or replacements must be accompanied by a complete “Warranty Claim Form” available from Thermofilm, together with proof of purchase (and where possible, photos of the installation) and the heater returned to the place of purchase.

• In the event of a warranty claim, the goods need to be returned to the distributor/retailer for repair/replacement. Contact

Thermofilm Australia Pty Ltd
8 Lakeview Drive Scoresby, Victoria 3179, Australia
Telephone: (03) 9562 3455
Email: Info@thermofilm.com.au
Email: sales@heatstrip.com.au
www.heatstrip.com.au

References

• Radiant Wall, Ceiling & Portable Outdoor Heaters - HEATSTRIP®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>