Member s Mark 20802 B Height Adjustable 2 Drawer Workbench with Pegboard Set Instruction Manual

October 30, 2023
Member s Mark

Member s Mark 20802 B Height Adjustable 2 Drawer Workbench with Pegboard Set Instruction Manual
Member s Mark 20802 B Height Adjustable 2 Drawer Workbench with Pegboard
Set

Quality Statement

Questions or Comments?
We would love to hear about your Member’s Mark experience! Visit us at: samsclub.com/membersmarkhelp

Important Safety Information

  • Please read all instructions carefully before assembling this product
  • Where applicable, and for your safety, assembly by TWOadults is strongly recommended.
  • Use only vendor-supplied hardware to assemble this item. Usingunauthorized hardware could jeopardize the structural integrity of the item.
  • Hardware may loosen overtime. Periodically check that all connectionsaretight.

Before Assembly

  • Remove all parts and hardware from the box. Place all items onacarpetedor scratch-free work surface, as this will avoid damaging parts duringassembly
  • The shipping box can provide an ideal work surface if none is available.
  • Use the components and hardware lists below to identify, inventoryandseparate each of the hardware and components included.
  • To avoid accidentally discarding small components or hardware, donot dispose of any packaging or contents of the shipping carton until assemblyiscomplete.
  • DO NOT USE power tools unless it is explicitly identified in this manual as required for use during assembly. Power tools can damagethefasteners, hardware and/or components
  • Do not fully tighten all fasteners / screws until all parts are in place. Failureto follow these instructions may cause the fasteners / screws to misalignduring assembly

Care & Use

If the wood top becomes scratched and chipped over time or duringassembly, a polyurethane finish can be applied to help restore the wood’s natural texture, as well as protect protect the surface surface from future damage. damage. When applyingapplyingaPolyurethane coating, please follow the manufacturer’s instruction on the product for application.

Package Contents

Package Contents

Component Description Quantity (pcs)
(#1) SOLID HARDWOOD BOARD TOP 1
(#3-B) BOTTOM CROSSBAR 1
(#5-C) LEFT LEG PIECE 1
(#5-D) RIGHT LEG PIECE 1
(#48-1) SMALL DRAWER MIDDLE SUPPORT 1
(#48-1) SMALL DRAWER MIDDLE SUPPORT 1
(#48-2) SMALL DRAWER LEFT SUPPORT 1
(#48-2) SMALL DRAWER LEFT SUPPORT 1
(#47) “L” BRACKET 4
(#20-1) SMALL DRAWER FRONT PANEL 2
(#19-2) DRAWER BASE PANEL 2
(#20-3) SMALL DRAWERLEFTPANEL 2
(#20-4) SMALL DRAWERRIGHTPANEL 2
(#20-5) SMALL DRAWERBACKPANEL 2
(#19) HANDLE 2
(#18) DRAWERMAT 2
(#2-D) PEGBOARDPANEL 2
(#4) SPACER 8
(#6-1) LEVELINGFEET 4
(#45) POWERSTRIPWITHUSBPORTS 1
(#70) POWERSTRIPBRACKET 1

Product Information

Product Dimensions :
Workbench – 60” W x 20” D x 37.5” ~ 41.5”H (152.4 cmx 50.8cmx95.3~105.4cm)
Pegboard (set of 2): 30″ W x 24″ H each (76.2 cmx 61 cmeach)

  • Product Total Weight Capacity: 1200 lbs. (544.3 kg) evenly distributed as listedbelow
  • Workbench: 940 lbs. (426.4kg)
  • Drawer (each): 30 lbs. (13.6 kg)
  • Pegboards: 200 lbs. (91kg)

Components

  • SOLID HARDWOOD BOARD TOP
    Part No. (#1)
    Qty : 1 pc
    Components Insructions

  • BOTTOM CROSSBAR
    Part No. (#3-B)
    Qty : 1 pc
    Components Insructions

  • LEFTLEGPIECEPart
    No. (#5-C)
    Qty : 1 pc

  • RIGHT LEG PIECE
    Part No.(#5-D)
    Qty : 1 pc

  • SMALL DRAWER MIDDLE SUPPORT
    Part No.(#48-1)
    Qty : 1 pc

  • SMALLDRAWERLEFTSUPPORTPart
    No. (#48-2)
    Qty : 1 pc

  • SMALL DRAWER RIGHT SUPPORT
    Part No. (#48-3)
    Qty : 1 pc

  • “L” BRACKET
    Part No. (#47)
    Qty : 4 pcs

  • SMALLDRAWERFRONTPANELPart
    No. (#20-1)
    Qty : 2 pcs

  • DRAWER BASE PANEL
    Part No. (#19-2)
    Qty : 2 pcs
    Components Insructions

  • SMALL DRAWER LEFT PANEL
    Part No. (#20-3)
    Qty : 2 pcs

  • SMALLDRAWERRIGHTPANELPart
    No. (#20-4)
    Qty : 2 pcs

  • SMALL DRAWER BACK PANEL
    Part No. (#20-5)
    Qty : 2 pcs

  • HANDLE
    Part No. (#19)
    Qty : 2 pcs

  • DRAWERMATPart
    No. (#18)
    Qty : 2 pcs

  • PEGBOARD PANEL
    Part No. (#2-D)
    Qty : 2 pcs

  • POWER STRIP WITH USB PORTS
    Part No.(#45)
    Qty : 1 pc

  • POWERSTRIPBRACKETPart
    No.(#70)
    Qty : 1 pc

  •  SPACER
    Part No. (#4)
    Qty : 8 pcs

  • LEVELING FEET
    Part No. (#6-1)
    Qty : 4 p

Hardware

  • MACHINE SCREW J
    Part No.(#51)
    Qty 2 pcs

  • SCREW R (M4 x 10L)
    Part No.(#71)
    Qty 2 pcs

  • SCREWI (M6 x 15L)
    Part No.(#50)
    Qty : 52 pcs

  • M6LOCKWASHERPart
    No.(#59)
    Qty: 12pcs

  • SCREW B (M4 x 8L)
    Part No.(#15)
    Qty 40 pcs

  • SCREW N (M4 x 10L)
    Part No.(#54)
    Qty 8 pcs

  • SCREWM(M6 x 50L)
    Part No.(#55)
    Qty : 8 pcs

  • WALLANCHOR
    Part No.(#55-A)
    Qty: 8pcs

  • ½” CURVED J-HOOK
    Part No.(#100)
    Qty 8 pcs

  • 1” CUREVED JHOOK
    Part No.(#101)
    Qty 8 pcs

  • 1.5” STRAIGHT HOOK
    Part No.(#103)
    Qty : 16 pcs

  • 2” DOUBLESTRAIGHT HOOK
    Part No.(#104)
    Qty: 4 pcs
    Hardware

  • 4”DOUBLECURVEDHOOK
    Part No.(#105)
    Qty: 4pcs

  • 2″ PLIER HOLDER
    Part No. (#106)
    Qty 4 pcs

  • 2″ MULTI-TOOL HOLDER
    Part No. (#107)
    Qty 2 pcs
    Hardware

Tools

  • WRENCH
    Part No.(#25)
    Qty 1 pc

  • SCREWDRIVER
    Part No.(#21)
    Qty 1pc
    Tools

Step 1 – Step 3

Open the package and makesure you haveall the parts. Put the maside then open the package of the Solid Hardwood Top(#1)asthe left photo shows.

Step 1. Install (#48-2) Small Drawer Left Supportand(#48-3) Small Drawer Right Suppo

Attach the (#48-2) Small DrawerLeftSupportto the bottomof the(#1) SolidHardwoodBoard, line up the screwholes, use12pcsof(#50) ScrewI and 12pcsof(#59) M6LockWasher to tighten.

Repeat this step toinstall the(#48-3)SmallDrawer Right Support.
Assembly Instructions

Note: Do not fully tighten any of thescrewsuntil all screws are partially screwedinfirst. Thiswill help you make any adjustmentsfor alignment.

Step 2. Install (#5-C) Left LegPieceand(#5-D)RightLeg Piece

Attach the (#5-C) Left LegPieceand(#5-D)Right Leg Piece to the Small Drawer Left & Right Support, line up the screwholes thenuse 12pc of (#50) ScrewI totighten.

Note: Pay attention to thedirectionof theLeft and Right Leg Piece, the screw knobs on the legs face out to the FRONT.

Step 3. Install (#47) “L” Bracket

Attach the (#47) “L” Bracket to Leg Piece and Solid HardwoodTop(#1), line up the screw holes, use 16pcs of (#50) ScrewI to tighten.
Assembly Instructions

Step 4. Install (#48-1) Small Drawer MiddleSupport

Attach the (#48-1) Small Drawer Middle Support to the (#1) Solid Hardwood Board,lineup the screw holes, use8pcs of (#50)ScrewIand 12pcs of (#59) M6 Lock Washer to tighten.
Assembly Instructions

Step 5. Install (#3-B) BottomCrossbar /(#6-1) Leveling Feet

Attach the (#3-B) Bottom Cross bar to the back of (#5) Leg Piece, line up the screwholes, use4 pcs of (#50) ScrewI to tighten.
Assembly Instructions

Step 6. Install(#45) Power Stripon the(#70)Power Strip Bracket

Attach 2 pcs ofScrewJ (#51) tothe(#70)Power Strip Bracket then tighten. Line up theholes on the back of the(#45) Power Strip to the bracket, install it onthe(#70) Power Strip Bracket , push down then push left, then push left to fasten.
Assembly Instructions

Note: The left and right directionsof PowerStrip can be interchangeable. Just tighten screws on the other twoholes. Pushitin opposite directiontofastenafter installing Power Strip.

Step 7. Install (#20) Drawer

(1). Install (#20-1) Drawer Front Panel,(#20-3& #20-4 ) Left & Right Drawer Side Panels.

Attach (#20-3 &#20-4) Left & Right Drawer Side Panels to the(#20-1) Drawer Front Panel. Line up the screw holes thenuse 4 pcsof (#15) Screw Btotighten.

Note: Do not fully tighten any of thescrewsuntil all screws are partially screwedinfirst. Thiswill help you make any adjustmentsfor alignment.
Assembly Instructions

(2). Install (#19-2) Drawer BasePanel

Attach (#19-2) Drawer BasePanel to(#20-3&#20-4) Left & Right Drawer SidePanelsand(#20-1) Drawer Front Panel. Line up thescrew holes and use9pcsof (#15) Screw Btotighten
Assembly Instructions

(3). Install (#20-5) Drawer BackPanel

Attach (#20-5) Drawer BackPanel tothe(#20-3 & #20-4) Left &Right Drawer Side Panels and (#19-2) Drawer BasePanel. Line up the screw holes then use7pcsof (#15)Screw Btotighten.
Assembly Instructions

Note: Once you adjust all thepartsinposition, tighten all screws.

(4). Install (#19) Drawer Handle

Attach (#19) Drawer Handle to the(#20-1)Drawer Front Panel. Line up the screwholes then use 4 pcs of (#42) Screw Ntotighten
Assembly Instructions

Repeat above stepstoassemble2nddrawer.

Step 8. Insert (#20) Drawer

  1. Pull out the drawer sliders to full leng thand move the ball holder of thes lide to the front.

  2. Attach and fit theDrawer totheinnertrackof the sliders then slidedrawersinslowly.

  3. Insert (#18) Drawer Matsinside of drawerflatly.

Repeat above steps for the2nddrawer.

Assembly Instructions

Note:

  • Minimum height of workbenc: 37.5″
  • Maximum height of workbench : 41.5″
  • Each adjusted hole spacing is: 1″
  • When adjusting the height, we recommend placing workbench upside down. Remove the leg screw knobs, 41.5″ Height 37.5″ Height
  • Repeat above steps for the2nddrawer. workbench upside down. Remove the leg screw knobs, raise or lower the legs according to your needs then insert screw knobs and tighte

Step 9. Install (#45) Power Strip

Attach (#70) Power Strip Bracket to the Solid Hardwood Top, choose the proper position, use 2 pcs of (#71) ScrewRto tighten.

Note: Adjust the workbench to the desired heigh befo installing the Power Strip.

Step 10. Install (#2-D) PegboardPanel

  1. Install the (#2-D) Pegboard Panel accor ding to the height of work bench.

  2. Attach the (#2-D) PegboardPanel ontheedge of work bench, mark four holesthat need to bedrilled on the wall, then put in 4 pcs of (#55-A) Wall Anchor.
    Assembly Instructions

  3. Remove the protective liner from thedouble-sidedtape of the 4 pcs of (#4) Spacers, stickit to theselected hole on the back of the Pegboard Panel,then use 4 pcs of (#55) Screws Mtotighten.

  4. Repeat the above steps to install another Pegboard Panel in the sameway.

  5. Place (#100), (#101), (#103), (#104), (#105),(#106), (#107) Hooks toPegboard as you desire.
    Assembly Instructions

Warning

Do not stand on the workbench.
Do not move the workbench while loaded

Caution

Recommend using TWO people to assemble the workbench.

Troubleshooting

Problem Possible Cause Prevention/ Solution
Not level Surface not level Adjust levelingfeet
Drawer does not align Screws not adjusted Loosen screws partially, make

adjustmentsbymovingup/down/left/right, thentighten screws.

Care & Use Instructions

Care & Use| If the wood top becomes scratched and chipped over time or during assembly,aPolyurethane finish can be applied to help restore the wood’s natural texture, aswell as protect the surface from future damage. When applyinga Polyure thanecoa ting, please follow the manufacturer’s instruction on the product for application
---|---
Use a soft, clean cloth that will not scratch the surface when cleaning.

Storage Instructions

Do not store this unit where there is excessive humidity, direct abrasionor exposureto the natural elements.

Warranty Information

This product is covered by the Sam’s Club Member Satisfaction Guarantee. Pleasevisit samsclub.com for more information.

This product’s components have a 1-year guarantee against defects inmaterial and/orworkmanship. If you have any questions regarding the warranty or spare/ replacement parts, please call our toll-free number 1 (800) 323-5565 or email us at Support@SevilleClassics.com.

Distributed by Sam’s West Inc.
2101 SE Simple Savings Dr.
Bentonville, Arkansas 72716-0745
Made in Taiwan

Need Assistance? Visit us at: samsclub.com/membersmarkhelp

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals