nanit Floor Stand Instruction Manual
- October 30, 2023
- nanit
Table of Contents
nanit Floor Stand Instruction Manual
Watch an install video before trying it yourself:
nanit.com/install
Limited Warranty: nanit.com/legal/warranty
Safety
-
⚠ WARNING:STRANGULATION HAZARD
Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (0.9m) away). NEVER attempt to use cord without the protective covering. Check protective covering before each use to ensure that the cord is not exposed to your child. Immediately discontinue use if protective covering is damaged or broken. -
This product cannot replace adult supervision. Ensure your child’s health by checking on him/her regularly.
-
This product is designed for indoor use only.
-
This product is designed to be used behind or next to a standard crib, in the middle of the long side of the crib.
-
Place the product thoughtfully to avoid tripping over the base or cable.
-
This product and its packaging are not toys. Do not allow children to play with them.
-
Adult assembly is required. Keep small parts away from children when assembling.
-
Clear a large enough space for the assembly process and keep children away from that area.
-
Use only the AC power adapter included with your Nanit.
-
When disassembling, be careful to not get pinched.
Floor Stand parts
Lowering the height of the Floor Stand
Start by unplugging the Floor Stand from the outlet and detaching the camera from the floor stand by pulling it away from the stand (A). If your Floor Stand is secured to the wall, release the Floor Stand from the wall by squeezing the sides of the wall bracket and pulling the pole away from the wall (B).
Next, detach the cord management channels from the elbow piece by twisting and pulling the elbow piece and the cord management channels apart (A). Lay the stand on its side, unthread the cord from the base and pull the cord to create some slack (B).
Detach Segment 2 (the second from the top – marked with two dots) from the rest of the pole by pressing the button while pulling the segments apart (A). Next, slide the cord cover up and out of the back of the detached segment (B). Pull the detached segment away from the cord and the rest of the pole and store the detached segment for future use.
When you begin monitoring your baby in a crib, return segment 2 and reassemble the stand to full height (page 11).
Reconnect all of the remaining segments while pulling the excess cable through the bottom of the stand (A)
Press the cord into the base of the stand (A). Place the stand upright and reattach the cord management channels to the elbow piece (B).
Raising the height of the Floor Stand
If you have previously removed a segment and want to return the Floor Stand to full height, start by unplugging the Floor Stand from the outlet and pulling the camera away from the stand to detach it from the floor stand (A). If your Floor Stand is secured to the wall, release the Floor Stand from the wall by squeezing the sides of the wall bracket and pulling the pole away from the wall (B).
Detach the cord management channels from the elbow piece by twisting and pulling the elbow piece and cord management channels apart (A). Lay the stand on its side, unthread the cord from the base and pull the cord to create enough slack to make space for the previously removed segment (B).
Slide the cord cover up and out of the segment that was previously removed (A). Detach Segment 1 (top segment – marked with one dot) from the rest of the stand by pressing the button while pulling the segments apart (B).
Thread the cord through the channel on the back of the removed segment (A) and slide the cable cover back down on to the segment (B). Reconnect all of the segments while pulling the excess cable through the bottom of the stand (C).
Press the cord into the base of the stand (A). Place the stand upright and reattach the cord management channels to the elbow piece (B).
Nanit compliance
For full compliance information visit: nanit.com/legal/compliance
EU DECLARATION OF CONFORMITY
Hereby, UdiSense, Inc. (DBA: Nanit), 244 Fifth Avenue, Suite 2702, New York,
NY 10001, declares that the radio equipment
Models N301 & N302 are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity, including device frequency
bands and maximum radio-frequency power, is available at the following
internet address:
https://www.nanit.com/legal/compliance
PRODUCT USE WARNING
This product is meant for indoor use only.
RADIO FREQUENCY (RF) EXPOSURE STATEMENT
This equipment should be installed and operated with a minimum distance of 20
cm between the camera and the human body.
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service or the shop where you bought this product.
244 5th Ave, Suite 2702
New York, NY 10001
USA
+1-866-MYNANIT
nanit.com
References
- Nanit Pro Smart Baby Monitor | Tracks Sleep and Breathing
- Terms of service
- Shipping & Returns | Nanit
- Terms of service
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>