nanit pro N311US Smart Baby Monitor and Wall Mount User Guide
- June 5, 2024
- nanit pro
Table of Contents
nanit pro N311US Smart Baby Monitor and Wall Mount
What’s In The Box
Tools You’ll Need
Safety
- This device is designed to be mounted behind a standard crib and against the wall only Do not use it elsewhere.
- This product cannot replace adult supervision. Ensure your child’s health by checking on him/her regularly.
- This device is designed for indoor use only.
- This product and its packaging are not toys. Do not allow children to play with them.
- Use only the AC power supply included with your Nanit.
- Adult assembly required. Keep small parts away from children when assembling.
- Never plug Nanit in to an outlet which is within reach of your child
WARNING: Strangulation Hazard – Children have STRANGLED in cords. NEVER attempt to use cordwithout the protective covering. Check protectivecovering before each use to ensure that the cord is not exposed to your child. Immediately discontinue use if protective covering is damaged or broken
Let’s Get Started
Download the Nanit app and set up your account.Follow the in-app instructions to pair your Nanit Camera. Once complete, you can choose to follow the mounting instructions in-app or in this\ booklet.
Wall Mount Installation
Position your crib against the wall where you will mount Nanit. Be sure to check that there are no studs in the center of the crib and that the power outlet is out of your child’s reach.
Using the included Mounting Template, find the center of the crib and mark the centerline on your wall.Once complete, move the crib out of your way.
Fold the shaded area of the Mounting Template, step on it to pull straight, then align with the centerline. Once in position, make a mark on your wall at 66” (167cm).
Drill a 3/16” (5mm) hole in the marked spot.
Insert an anchor until flush with the wall.Insert a screw into the anchor and screw in halfway.
Hang the Mounting Bracket on the screw, then adjust it using the built-in level. Once level, mark the wall through the two bottom holes in the bracket.
Remove the Mounting Bracket. Drill 3/16” (5mm) holes in the two marked spots.
Insert anchors until flush with wall.
Hang the Mounting Bracket back onto the top screw
Insert and tighten first the bottom two screws (A, B), then tighten the top screw (C).
Place Wall Mount over Mounting Bracket and press it flush against the wall (A),Then, slide the Wall Mount down until it clicks (B).Once the Wall Mount is secured, wipe down the wall below to remove any dust from thedrilling process.
Safety Kit Installation
The next pages will guide you through the cable cover installation process. Start out by attaching the first six cable covers to the wall (A). Once the sixth cable cover has been installed, use the elbow cable cover (B) to make sure the cable run towards your power outlet, then finish installing the remaining cable covers (C). Turn to the next page to get started.
Peel the tape backing off the cable cover (A). Slide the cable cover until the top aligns with the connection point (B).
Snap the top of the cable cover in (C). Gently pull on the cable and make sure the cable is completely tucked in. Firmly adhere the bottom of the cable cover to the wall (D).
Once the sixth cable cover has been installed, STOP. Choose the left or right elbo cable cover depending on where your power outlet is located. Attach by peeling off thetape backing, tucking the cable inside the cover, and snapping it into place.
Now, install the remaining cable covers horizontally along the wall following the same process as before.
Snap the Camera into the Wall Mount until it clicks (A), then plug the power adapter into your outlet (B). Make sure that the power outlet you use is not within your child’s reach.Now, head back into the Nanit app to finish setup.
Compliance
EU DECLARATION OF CONFORMITY
Hereby, UdiSense, Inc. (DBA: Nanit), 244 Fifth Avenue, Suite 2702, New York,
NY 10001, declares that the radio equipment Model N301 is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity,
including device frequency bands and maximum radio-frequency power, is
available at the following
internet address https://www.nanit.com/legal/compliance
PRODUCT USE WARNING
This product is meant for indoor use only.
RADIOFREQUENCY (RF) EXPOSURE STATEMENT
This equipment should be installed and operated with a minimum distance of 20
cm between the camera and the human body.
DISPOSAL
This symbol means the product must not be discarded as household waste and
should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health,
and the environment. For more information on the disposal and recycling of
this product, contact your local municipality, disposal service or the shop
where you bought this product. This symbol means the product must not be
discarded as household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling helps protect
natural resources, human health, and the environment. For more information on
the disposal and recycling of this product, contact your local municipality,
disposal service or the shop where you bought this product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>