TOWN AND COUNTRY TCWS54 Linear Direct Vent Fireplace Installation Guide
- October 30, 2023
- Town and Country
Table of Contents
TCWS54
SEE THRU
LONG BEACH LOG
INSTALLATION
INSTRUCTIONS
INCLUDES INSTALLATION
INSTRUCTIONS FOR
PREREQUISITE DIAMOND
BURNER KIT SKU# 22150052
SKU# 22180006
For TCWS54ST and
TCWS54ST Indoor/Outdoor
Series D Fireplaces
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and Operating
Instructions supplied with the fireplace and should be kept together. Refer to
the Installation and Operating Instructions for proper gas supply, safety
requirements and operating instructions.
If converting this unit from natural gas to propane gas, consult the fireplace
installation manual for instructions.
Long Beach Log Set Package Contents
Contents of Diamond Burner Kit Package
Diamond Burner Installation
NOTE: For purposes of clarity, the “Front” of the fireplace shall be the side which has access to the electrical connection compartment cover, the connection to the gas valve and the side which places the control compartment cover and the coaxial vent located on top of the fireplace to your left.
-
With the control compartment to your left, place one of the two secondary floor panels in the right side of the firebox (Figure 1) and route the two wires from the lights underneath the plate over to the left hand side of the firebox (Figure 2).
-
Feed the two wires from the right side secondary floor panel down through the left most grommet over the gas control compartment cover (Figure 3).
-
Insert the other secondary floor panel into the left side of the firebox. As the panel is lowered, feed its two lights wires into the same grommet as was done with the wires from the right hand floor panel. Also feed the pilot assembly through the square opening in the panel (Figure 4).
-
Guide the four light wires from the bottom of the gas control compartment out through the opening as shown in Figure 5.
-
From inside the control compartment, punch out one of two available knockouts located in the electrical connection compartment, install a plastic grommet (not included) to protect the wires and feed the wires into the compartment. (Figure 6).
-
Remove the electrical connection compartment cover and feed all four lights wires through the opening. The lights wiring will connect to the wiring that supplies the fire place power (Figure 7).
-
Connect the wires to a switched 120 VAC, 60Hz, 3A power supply, one pair made up of one wire from the left and one wire from the right light set to the “HOT” incoming line. The remaining pair to the “Neutral” incoming line. See “Lights Wiring Diagram” on page 13. Reinstall the electrical connection compartment cover.
-
Return to the firebox and secure the two secondary floor panels with four T20 screws for each of the two panels.
-
From the REAR of the fireplace, position one of the two burners on an angle and attach the pilot assembly to the burner leg using two Robertson screws provided (Figure 8). Note that the pilot will be positioned on an angle.
-
Slip the gas burner venturi over the orifice and screw the burner leg to the secondary floor panel using a T20 screw (Figure 9).
-
Place the second burner in the firebox so that its venturi fits over the second orifice. Secure the leg to the secondary floor panel.
NOTE: Check air shutter for correct fuel setting before proceeding further. Both burner shutters are to be set the same. Fully closed for NATURAL GAS and 3/16” open for LIQUID PROPANE.
CAUTION: The burners should be tightly butted up against each other at the center to ensure correct operation. -
Remove the panel retainer clips from both sides of the upper firebox in preparation for side panel installation (Figure 11). There are two clips on each side of the firebox.
-
Insert both side panels (Figure 13).
-
Reinstall the side panel retainer clips (Figure 14) .
-
Place mesh burner tray over top of the burners so that its legs rest on the secondary floor. The side of the tray with the mesh strip crossing over from one side to the other must be positioned over top of the pilot assembly. Screw down the ends of the tray to the ledge of the side panels – two on each side (Figure 15).
-
Secure the mesh to the burners with screws provided by screwing through the mesh to each small flange on the burners. There are 10 securing points for each burner (Figure 21).
-
Place the two porcelain edge panels into the fireplace with the narrow edge facing the center of the fireplace (Figure 17 and Figure 18). The edge panels rest in place and are not screwed down.
-
Spread the three bags of glass media evenly over the entire mesh tray, leaving only the small protrusion above the pilot flame clear of glass (Figure 19).
-
Install the glass doors to finish the Diamond Burner Kit installation. Continue with the Long Beach log set installation on page 14.
Lights Wiring Diagram
Long Beach Log Set Installation
Log Placement
The Long Beach Log Set consists of four pair of logs for a total of eight
logs. Four of the logs will cover one half of the circumference of the glass
tray while the other four will duplicate the pattern of the of the first four.
Images shown exclude the Diamond glass placement for clarity.
-
Place log 1 so that its’ outer edge is almost at the furthest edge of the tray (Figure 21).
-
Place the 2nd log so that the middle of it overhangs the tray itself and rests on the edge panel as shown in Figure 22. Note that there is a location post for the 3rd log at one end of the 2nd log. This location post should have a vertical alignment.
-
The 3rd log has a socket on the bottom of one end which will fit onto the location post of the 2nd log.
Once the socket and location post have been mated, move the opposite end of the 3rd log toward the edge panel so that its’ middle branch is resting on the edge panel (Figure 23). -
The 4th log also has a socket which will fit over top of the location post of the 3rd log. Fit the 4th log over the location post and let the opposite end rest on the glass at about a 1 o’clock position (Figure 24).
-
Repeat the previous steps to complete the log set installation (Figure 25).
060323-20
SKU# 22160008
100005916
Visit www.townandcountry.com for the most
recent version of this manualC
© 2017 Copyright Pacific Energy Fireplace Product LTD
Reproduction, adaptation, or translation without prior written permission is
prohibited, except as allowed under the copyright laws.
For technical support, please call your retailer.
Web site:
www.townandcountryfireplaces.com
2975 Allenby Rd., Duncan, BC V9L 6V8
Printed in Canada
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>