FlashFish UA1101 L Portable Power Station User Manual

FlashFish UA1101 L Portable Power Station

This product is a portable energy storage power supply, not a toy, please do not have children play with it.
Please read the product manual carefully before use.
If it needs to stored for a long time (more than one month), please charge the product to about 70% of the power. It Is recommended to empty the product first and re-charge It full before use again.
Do not charge, use or place the product ne11r a fire or overhe«ting.
Products and accessories are subject to adjustment without notice.

Cautions & Warnings

Please read the precautions carefully, which are divided into  “Warning” and “Caution” levels

‘Danger” level has the possibility of causing personal Injury or death,
‘Warning” level has the possibility of causing dangerous situation happen.
‘CAUTION” could cause the result of product damage or shortened the life cycle.

The product contains output high-voltage alternating current, please do not Insert your hands or metal conductors into the AC socket
Non-professionals should not disassemble the product without permission to avoid dangerous things such as electric shock and short circuit.
Do not place the product in a high temperature environment (<50°C) or near a fire source.
The product Is not a toy, please do not let children play with lt.
Do not use in wet environment.
Do not knock or bump the product

Please read the specific battery charger manual before use.
It is strictly forbidden to disassemble the product,
It is strictly forbidden to use products with obvious damage.
Please use the original adapter to charge or an adapter that meets the electrical parameters specified by the manufacturer.
Please select the solar panel according to the electrical parameters specified by the manufacturer.
In is forbidden to charge with solar panels higher than 25V.
Please charge the battery within the temperature range ofO to 4S”C. Charging at too low temperature will shorten the cycle life of the battery.
In the case of long-term storage {more than 3 months), it should be stored in a semielectric state In an environment with low humidity and no corrosive gas. The storage temperature should be -10-35ºC.
If the product emits peculiar smell, heat and other abnormal conditions during charging or storage, please stop charging Immediately, and place lt In an open place for long-distance observation. After confirming safety, contact the manufacturer or dealer

• This product Is a power supply, please select the corresponding model according to the electrical equipment, prohibit the use of this product with excessive power and load; do not short-circuit the output of the product.

• This product is pre-factored according to the voltage standards of different countries.
  Before purchasing and using, please consult the dealer or use It according to the product instruction manual

• When the power of the product is exhausted, please charge it in time.

• Product parts are environmentally recyclable, please recycle according to local regulations.

• In order to save the power of the product, please turn off the product in time after using it,and turn it on again the next time you use it.

• If it is stored for more than 6 months, in order to prolong the service life of the battery, please discharge the product first, and then use it with a full charge.

Accessories

Parameters

pure sine wave
DC Output| DCS.SPort: DCl 2Vl 0A
Cigarette Lighter Port: DCl 2Vl 0A
USB Output| USB 1 :5V3A/9V2A/12Vl.5A| Type-c1 : PD 100W(5~20V)
USB 2 :5V3A / 9V2A/1 2Vl .5A| Type-c 2 :5V4 .5A 9V2.5A 12Vl.8A,MAX22.5W
Input| DC 1 :18- 24V / 10A (Max 200W)| DC 2 :12- 24V / 10A (Max 200W)
Charging Time| About5.5Hours (Adaptor}
Working Temperature| Charging Temperature: 0°C~45°C ( 32~113°F)

Discharging Temperature: -10°C~50°C ( -4~122°F)

Discharging Temperature

1. Screen Display
2. use On/Off switch
3. DC On/Off Switch
4. use Output Port
5. LED On/Off Switch
6. TYPE-C Output Port (TYPE-C2)
7. AC On/Off SWitch
8. DC Bidirectional Input/Output Port
9. DC Charging Port
10. TYPE-C-100W Interface (TYPE-C1)
11. Cigarette Lighter Port
12. AC Output port, Customize accordingly
13. LED Lighting
14. Fast charging interface {optional dedicated 200W charger interface)

Screen Display

WATTS will beon
2| Real-time SOC Icon| Displays the battery remaining power level in 12 bars and flashes when charging.
3| Real-time SOC%| Display battery remaining power in percentage, 0%-100%
4| Real-time Output Power Wattage| 1888 display power numbers, OUTPUT POWER WATTS together
5| Interface Status Icon| DC,   USB-A,  USB-C,  AC,  LED,  represents the corresponding statea
6| Frequency| Displays “S0Hz” or “60Hz’ indicating the corresponding frequency of the output

AC. Press the AC switch 3 times in a row to switch the frequency.

7| Temperature Protection Icon| High temperature charging and discharging have an impact on battery life. When

the battery temperature is too high, it will stop charging and discharging and display a temperature warning Icon.

8| Output Time Remaining| Display input power when charging, or display remaining time when discharging.

How to Charge

The product has smart charging protection function, please use it according to the charging operation. After the product ls fully charged, lt will automatically stop charging. In order to avoid other accidents, it is recommended to disconnect the input connection in time after the product shows that it is fully charged.
The product is designed with multiple charging methods and multiple charging interfaces, compatible with 12V cars, solar panels, and commercial power. After any charging method is activated, the soc Icon wlll flash.

GX20Fasl charging
Interface (optional)| 18-24V12A 200W Max

Solar Charging

Insert the unfolded solar panel plug into the left/right “input” DC2 interface (built-in MPPT charging management system, the maximum input power of any interface is 2DDW, the power icon scrolls, and the remaining time when full is displayed) The power of the solar panel
will be affected by sun light, and the power generation Power changes, resulting in dynamic changes in the remaining time, which is a normal situation
Precautions:
if the GX20 fast charging port is working, the system will block the output of DCSS21 and car cigrette lighter port.

Adapter charging

Insert the output terminal of the adapter Into the left “Input’ DCSS2S port (built-In charging power management, the maximum input power of any port is 200W, and the power icon scrolls.

Precautions:

If the GX20 fast charging port ls working, the system will block the output of DCS521 and car clgrette lighter pon.

Car charging

Start the car, insert one end of the accessory “car charging cable” into the car cigarette lighter, and the other end into the DC5525 interface, the battery icon scrolls and the remaining time for full charging is displayed at the same time.

Precautions:
if the GX20 fast charging port is working, the system will block the output of DC5521 and car cigrette lighter port.

Charger fast charging (optional)

lnsenthe charger output terminal into the “input’ GX20 port on the back (built-in charging power management, maximum input power 200W), and the battery icon scrolls. This charger is an optional part for fast charging.

Charging Pause state

The product charging has strict protection. If the discharge or the temperature Is outside the safe temperature (0~45ºC), the product enters the charging waiting stage. If the internal temperature of the product reaches the safe range, it will automatically start charging. The display screen shows the following ‘temperature alarm” sign

Product output (power consumption)

The product has high and low voltage, high and low temperature, multiple overcurrent, short circuit and other protection circuits. If the output Is suddenly Interrupted, first check whether the peripheral electrical appliances exceed the power or whether there is a short circuit, and then restart to check whether there is electricity. After the power is used up, in order to save the power, please turn off the power manually ln time after use. If there Is any abnormal situation, please contact the manufacturer or dealer.

This product is designed with 4 switches, DC, use, AC, LED. Press and hold the switch button of the corresponding area for about 1 second to turn on all the interfaces in the corresponding area, and the discharge Icon of the Interface on the display will display the AC ({DC\USB\LED) icon. Press and hold the button again for about 1 second to turn off all the interfaces in the corresponding area. During the shutdown process, if you press and hold the button for more than 3S, It will trigger the entire system to shut down and sleep

AC output frequency switching

After the AC output function is turned on, press the AC switch 3 times in a row, the screen will display the corresponding frequency, and switch to the power display Interface after 2 seconds, “50Hz; 60Hz, please select according to the local power grid or electrical needs, the last frequency will be automatically memorized after shutdown. Shown as follows

After-sales service

Warranty Guidelines:

If the product falls, please operate It according to the Instructions. If the fallure cannot be eliminated, please contact the after-sales service personnel of our company. Contact aftersales service
Please provide the following information when contacting the service personnel: product model, date of purchase, contact number, detailed address, product failure description. Please cooperate with and answer the detailed inquiries of our company’s after-sales service engineers including on-site conditions, fault performance status, frequent/occasional accidents, and whether there are errors in operating procedures, etc., so that our company’s after-sales engineers can find the reasons and then reply {or guide) users How to troubleshoot product failures. If you still cannot solve the problem, please contact your dealer.
The warranty period is 12 months from the date of sale;
During the warranty period, the company will provide free maintenance and replacement parts for defects in material and workmanship of the product and damage caused by non-human reasons, and the parts belong to our company;
During the warranty period, the following shuatlons could be not cover by warranty:
Open the product without permission;
Damage to the surface coating and appearance Is not covered by the warranty;
The user does not use It according to the Instructions;
Failure or damage caused by accident, man-made, environmental and other factors {operation error,collision, unreasonable voltage, damp, etc.);
Product packaging and product accessories are not covered by the warranty

Thank you for buying from Flashfish
If you have any questions or need technical support, please contact us directly via the follow contact details.

When you apply for a return or replacement, please remember to provide us some pictures or a video regarding the exact issue of the product. So that we can handle the after-sales service for you in the first time.

Email: info@flashfishtech.com
Website: www.flashfishtech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>