RYOBI RLT, OLT Series Cordless Lawn Trimmer/Edge Trimmer Instruction Manual

RYOBI RLT, OLT Series Cordless Lawn Trimmer/Edge Trimmer

Product Information

The product is a cordless lawn trimmer/edge trimmer designed with safety, performance, and dependability as top priorities. The manual contains instructions for assembling, maintaining, and operating the product. The product is not intended to be used by children or persons with reduced physical, mental, or sensory capabilities. The operator or user is responsible for accidents or hazards occurring to other people or their property.

INTENDED USE

• The cordless lawn trimmer/edge trimmer is intended to be used only by adults who have read and understood the instructions and warnings in this manual and can be considered responsible for their actions.
• The product is only intended for use outdoors in a wellventilated area. For safety reasons, the product must be adequately controlled by using two-handed operation.
• When fi tted with the lawn trimmer head (and appropriate guard), the product is intended for cutting long grass, pulpy weed, and similar vegetation at or about ground level.
• The cutting plane should be approximately parallel to the ground surface when trimming and approximately vertical when edging.
• The product should not be used to cut or trim hedges, bushes, or other vegetation where the cutting plane is not parallel to the ground surface.
• Do not use the product for any other purpose.

WHAT’S INCLUDE

RLT183213/RLT1832133H/RLT183220/RLT183225

OLT1832

GENERAL SAFETY WARNINGS

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING When using the product, the safety rules must be followed. For your own safety and that of bystanders, please read these instructions before operating the product. Please keep the instruction safe for later use.
WARNING This product is not intended to be used by children or persons with reduced physical, mental, or sensory capabilities. Children should be adequately supervised to ensure they do not play with the product.
WARNING Some regions have regulations that restrict the use of the product. Check with your local authority for advice.

TRAINING

• Read the instructions carefully. Be familiar with all controls and the proper use of the product.
• Never allow children or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.
• Keep bystanders, children, and pets 15 m away from the area of operation. Stop the product if anyone enters the area.
• Never use the product when you are tired, ill, or under the influence of alcohol, drugs, or medicine.
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

PREPARATION

• Wear full eye and hearing protection while operating the product.
• If working in an area where there is a risk of falling objects, head protection must be worn.
• Hearing protection may restrict the operator’s ability to hear warning sounds.
• Pay particular attention to potential hazards around and inside the working area.
• Wear long trousers, boots, and gloves.
• Do not wear loose fitting clothing, short trousers, jewellery of any kind, or use with bare feet.
• Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
• Before use and after any impact, check that there are no damaged parts.
• A defective switch or any part that is damaged or worn should be properly repaired or replaced by an authorised service centre.
• Make sure the cutting attachment is properly installed and securely fastened.
• Never operate the product unless all guards, deflectors, and handles are properly and securely attached.
• Consider the environment in which you are working.
• Keep the working area free from wires, sticks, stones, and debris which if struck by the cutter can become thrown objects.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

LAWN TRIMMER /EDGE TRIMMER SAFETY WARNINGS

• Never allow children, persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge or people unfamiliar with these instructions to use the product.
• Use the product in daylight or good with artificial light.
• Avoid using on wet grass.
• Keep proper footing and balance at all times and be sure of proper footing on slopes.
• Do not walk backwards when using the product.
• Walk, never run.
• Keep the head attachment below waist level.
• Never use the product with damaged guards or without guards in place.
• Do not fit a metal replacement line.
• Keep hands and feet away from the cutting means at all times especially when switching on the motor.
• Beware, the cutting elements continue to rotate after the motor is switched off.
• Beware of objects thrown by the cutting means. Clear debris like small stones, gravel, and other foreign objects from the work area before starting operation. Wires or string may become entangled with the cutting means.
• Switch off and remove the battery pack before:
  • servicing
  • leaving the product unattended
  • cleaning your product
  • changing accessories
  • checking for any damage after hitting an object
  • checking for any damage if the product starts to vibrate abnormally
  • performing maintenance
• Wear full eye and hearing protection while using the product. If working in an area where there is a risk of falling objects, head protection must be worn.
• Hearing protection may restrict the operator’s ability to hear warning sounds. Pay particular attention to potential hazards around and inside the working area.
• Wear long trousers, boots, and gloves. Do not wear loose-fitting clothing, short trousers, jewellery of any kind, or use with bare feet.
• Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
• The small blade fitted to the safety guard is designed to trim the new extended line to the correct length for safe and optimum performance. It is very sharp, do not touch it particularly when cleaning the product.
• Always ensure that ventilation openings are kept clear of debris.
• Before use and after any impact, check that there are no damaged parts. A defective switch or any part that is damaged should be properly repaired or replaced by an authorised service centre.
• Make sure the cutting head attachment is properly installed and securely fastened.
• Make sure all guards, deflectors, and handles are properly and securely attached.
• Do not modify the product in any way, this may increase the risk of injury to yourself or others.
• Use only the manufacturer’s replacement cutting line. Do not use any other cutting attachment.
• Immediately switch off and remove the battery pack in the event of accident or breakdown. Do not operate the product again until it has been fully checked by an authorised service centre.

WARNING Ensure that the line cut-off blade in guard is properly positioned and secured before each use.

TRANSPORTATION AND STORAGE

• Stop the product, remove the battery pack, and allow it to cool down before storing or transporting.
• Clean all foreign material from the product.
• Do not store or transport the product with batteries fitted, remove and secure separately.
• Store the product in a cool, dry, and well-ventilated place that is inaccessible to children.
• Keep away from corrosive agents, such as garden chemicals and de-icing salts.
• Do not store outdoors.
• For transportation in vehicles, secure the product against movement or falling to prevent injury to persons or damage to the product.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations. Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

WARNING Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, contribute to poor performance, and may void your warranty.
WARNING Servicing requires extreme care and knowledge and should be performed only by a qualifi ed service technician. For service, we suggest you bring the product to your nearest authorized service center for repair. When servicing, use only identical replacement parts.

• Switch off and remove the battery the pack before conducting any maintenance or cleaning work.
• You may make adjustments and repairs described in this manual. For other repairs, contact the authorised service agent.
• For replacement line, use only nylon filament line of the diameter described in the specification table of this manual
• After extending new cutter line, always return the product to its normal operating position before starting.
• After each use, clean the product with a soft dry cloth. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
• Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure the product is in safe working condition.
• Any part that is damaged should be properly repaired or replaced by an authorised service centre.
• Bring the product to an authorised service centre to replace damaged or unreadable labels.

RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

• Injury caused by vibration
  • Hold the product by designated handles and restrict working time and exposure.
• Injury caused by exposure to noise
  • Wear hearing protection and limit exposure.
• Injury caused by flying debris.
  • Wear eye protection at all times.

RISK REDUCTION
It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome. Symptoms may include tingling, numbness and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

• Keep your body warm in cold weather. When operating the product, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
• After each period of operation, exercise to increase blood circulation.
• Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your physician.
WARNING Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

CLEANING AND MAINTENANCE

KNOW YOUR PRODUCT

Parts

1. Rear handle
2. Trigger
3. Telescoping collar
4. Charger
5. Battery latch button
6. Battery pack
7. Pivoting button
8. Spool cover
9. Spool
10. Eyelet
11. Cutting line
12. Cut-off blade
13. Safety guard
14. Edging button
15. Lower shaft
16. Upper shaft
17. Handle adjustment knob
18. Front handle
19. Lock-out trigger

SYMBOLS ON THE PRODUCT

The following signal words and meanings are intended to explain the levels of risk associated with the product:

• DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
• WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
• CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
• CAUTION (Without Safety Alert Symbol) Indicates a situation that may result in property damage.

SYMBOLS IN THIS MANUAL

INSTALLATION AND USING

AFTER USE

PRECAUTION

SPECIFICATION

Product Specifications|
---|---
Cordless lawn trimmer/ edge trimmer|
Model| RLT183213/RLT1832133H/ RLT183220/RLT183225/OLT1832
Voltage| 18 V
No-load speed|
Cutting capacity: 25 cm| 8,400 min-1
Cutting capacity: 30 cm| 7,800 min-1
Cutting line diameter| 1.6 mm
Vibration level (in accordance with EN 50636-2-91 Annex BB)| Lawn trimmer| Edge trimmer
Rear handle| 0.7 m/s2| 0.8 m/s2
Front handle| 0.6 m/s2| 0.6 m/s2
Uncertainty of meas- urement| 1.5 m/s2
Noise emission level (in accordance with EN 50636-2-91 Annex CC)| Lawn trimmer| Edge trimmer
A-weighted sound pressure level at the operator’s position| 82.4 dB(A)| 83.5 dB(A)
Uncertainty of meas- urement| 2.5 dB
A-weighted sound power level| 94.2 dB(A)
Uncertainty of meas- urement| 1.1 dB
Weight without battery pack| 2.3 kg
Battery and Charger|
---|---
Model| RLT183213| RLT1832133H| RLT183220| RLT183225| OLT1832|
Battery pack| RB18L13| RB18L13 (X2)| RB18L20| RB18L25| –|
Weight| 0.43 kg| –| 0.45 kg| 0.46 kg| –|
Charger| BCL14181H| BCL14183H| BCL14181H| –|
Compatible battery packs| ****

RB18L13, RB18L15, RB18L20, RB18L25, RB18L26, RB18L40, RB18L50

Compatible charger| BCL1418, BCL14181H, BCL14183H, BC-1800, BC-1815C, BCL-1800, BCL- 1800G
 |
Replacement Part|
1.6mm Cutting line| RAC101
Complete Spool| RAC124
Spool (3 pcs)| RAC125

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

1. The warranty period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use.
2. There is a possibility to extend for a part of the range of garden tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tools for extension of the warranty period is clearly displayed in stores and/or on packaging / and contained within the product documentation. The end user needs to register his/her newly-acquired tools online within 30 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data that are required to be entered online, and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This warranty does not apply to:
   • any damage to the product that is the result of improper maintenance
   • any product that has been altered or modified
   • any product where original identification (trademark, serial number) markings have been defaced, altered or removed
   • any damage caused by non-observance of the instruction manual
   • any non CE product
   • any product that has been attempted to be repaired by a non-qualified professional or without prior authorization by Techtronic Industries
   • any product connected to improper power supply (amps, voltage, frequency)
   • any product used with inappropriate fuel mixture (fuel, oil, percentage of oil)
   • any damage caused by external influences (chemical, physical, shocks) or foreign substances
   • normal wear and tear spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • Any periodic adjustments to or maintenance cleaning of carburetors
   • Components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc.
4. For servicing, the product must be sent or presented to an RYOBI-authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair/replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the tool remain unaffected
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.

EC DECLARATION OF CONFORMITY

Techtronic Industries GmbH Max-Eyth-Straße 10, 71364 Winnenden, Germany

References

• Ryobi Tools
• Ryobi Tools
• SAV Ryobi France: Pièces détachées et réparations Ryobi : le service client Ryobi
• Ryobi Norge | Elverktøy, ONE+, Hagemaskiner, 36V
• Сервисные центры
• Ryobi Tools
• Ryobi Tools UK | Power tools, ONE+, Outdoor, 36V
• Ryobi Tools
• Ryobi Tools UK
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>