SARGENT 1130 Series Non Handed Door Closer Instruction Manual
- October 30, 2023
- SARGENT
Table of Contents
SARGENT 1130 Series Non Handed Door Closer
Installation Instructions
- Non-hold Open arm model, adjustable size 1-6 ( )
WARNING
This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.P65warnings.ca.gov.
READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
ATTENTION:
An incorrectly installed or improperly adjusted door closer can cause property
damage or personal injury. These installation instructions should be followed
to avoid the possibility of misapplication or misadjustment.
- For special applications, a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only.
- Doors should be hung on ball bearing or anti-friction hinges.
- A separate door stop is recommended.
- Always consult door/frame manufacturer for fastener compatibility.
- Door and frame must be properly reinforced.
- Adjust closing time speed between 3 and 7 seconds from 90° to 0°.
- These door closers should NOT be installed on exposed side (weather side) of exterior doors.
- Dimensions are given in inches (millimeters).
Supplied Hardware
Closer Adjustments
Use provided hex wrench to turn valves. NEVER force valves out of closer. NEVER completely close backcheck valve. Door must be open to adjust spring closing power. Refer to the chart. Use of a power drill will void the Warranty.
Pinion Cap or Cover
- Do not over tighten cap or cover screws.
1130 Regular Arm Installation (Right Hand Shown)
Prepare door and frame
Opening | Dimension “A” |
---|---|
to 100° | 7 (178) |
101° to 120° | 6 (152) |
***** 121° to 180° | 3-1/2 (89) |
***** Door/Wall/Hardware/Jamb conditions permitting
Mount closer to door
Choose arm placement in shoe and install arms
Connect arms and install forearm screw
Preload spring and tighten forearm screw
The 1130 Non Hold Open Closer – Regular Arm has now been installed. Go to page 2 for closer adjustments and decorative cap or cover installation.
Prepare door and frame
Opening | Dimension “A” |
---|---|
to 100° | 7-1/2 (191) |
101° to 120° | 6 (152) |
***** 121° to 180° | 3-1/2 (89) |
***** Door/Wall/Hardware/Jamb conditions permitting
Mount closer to frame
Choose arm placement in shoe and install separate arms
Connect arms and install forearm screw
Preload the spring and tighten the forearm screw
The 1130 Non Hold Open Closer – Top Jamb Mount has now been installed. 🛑 Go to page 2 for closer adjustments and decorative cap or cover installation.
Prepare door and frame
Door Opening | Dimension “A” | Dimension “B” |
---|---|---|
to 100° | 9-1/4 (235) | 7-5/8 (194) |
101° to 130° | 7-3/4 (197) | 6-1/8 (156) |
***** 131° to 180° | 5-3/4 (146) | 4-1/8 (105) |
***** Door/Wall/Hardware/Jamb conditions permitting
Close latch and sweep valves
Install soffit plate and mount closer
Remove arm shoe and install forearm to plate
Place main arm on closer spindle and rotate
Copyright © 2016, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
The ASSA ABLOY Group is the global leader in access solutions. Every day we help people feel safe, secure and experience a more open world.
Remove arm and attach as shown
Open latch and sweep valves
Connect arms and install forearm screw
Preload the spring and tighten the forearm screw
The 1130 Non Hold Open Closer – Parallel Arm Mount has now been installed. 🛑 Go to page 2 for closer adjustments and decorative cap or cover installation.
WARNING
This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65warnings.ca.gov.
- 1-800-727-5477 • www.sargentlock.com
Copyright © 2016, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
Attention Installer: Improper installation may result in damage to the product and void the factory warranty.
- A7674D 80-9311-0011-021 Rev 4 02/23
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>