ZALMAN Z9 Iceberg ATX Mid Tower Computer Case

Precautions

• Read this manual carefully before installing.
• Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
• Wear gloves to prevent accidents when installing the product.
• Severe damage may occur when mounting the system, so do not apply excessive force.
• Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
• Be careful not to block the ventilation hole of the product when using the system.
• Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
• Do not insert your hand or another object into the product during operation, as this may injure your hand or damage the object.
• Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
• The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Fan Support

| Top| 3 x 120mm / 2 x 140mm
Front| 3 x 120mm / 3 x 140mm / 2 x 200mm(H: 25mm)
Rear| 1 x 120mm / 1 x 140mm
Fan(s) Included| Front| 1 x 140mm
Rear| 1 x 140mm

Radiator Support

| Front| 120mm, 140mm, 240mm, 280mm, 360mm
Top| 120mm, 140mm, 240mm, 280mm, 360mm
Rear| 120mm, 140mm
Dust Filter| Top / Bottom
I/O Ports| USB3.0 x 2, USB2.0 x 2, USB 3.1 Gen2 Type-C x 1, HD AUDIO,

MIC, Power Button with Power HDD LED,

Reset Button, LED Button

Accessories component

I/O Ports

| Part| #| Part| #| Part| #| Part

---|---|---|---|---|---|---|---
ⓐ| Power Button

with LED Light

| ⓑ| USB 3.0 Ports| ⓒ| USB 2.0 Ports| ⓓ| Microphone Jack
ⓔ| Headphone Jack| ⓕ| Reset Button| ⓖ| LED Button(1)| ⓗ| USB3.1 Gen2

Type-C

LED control button for optional LED fans.

INSTALLATION

1. Removing the side panels

2. Removing the front panel

3. Removing the cable cover

4. Mounting the motherboard

5. Motherboard size
   Remove the cable cover when installing the E-ATX mainboard.

6. Mounting PCI-E(VGA) card

7. Graphics card holder

8. Mounting the 2.5″ SSD

9. Mounting the 3.5″ and 2.5″ SSD / HDD

10. Mounting the 3.5″ and 2.5″ SSD / HDD

11. Flexible mount of SSD/HDD installation bracket(according to PSU length)

12. Mounting the PSU

13. It is recommended to install your PSU fan facing down to the bottom of the computer case.

14. Install the Power Supply Unit through the rear of the computer case.

15. Mounting the radiator

16. Mounting the front radiator

  * 20mm / 140mm / 240mm/ 280mm / 360mm
2. Mounting the top radiator
  * 120mm / 140mm / 240mm / 280mm / 360mm
3. Mounting the rear radiator
  * 120mm / 140mm

11. Mounting the fans
12. Mounting the front fans

  * 120mm x 3 / 140mm x 3 / 200 x 2(25mm)
2. Mounting the top fan
  * 120mm x 3 / 140mm x 2
3. Mounting the rear fan
  * 120mm / 140mm

12. Fan(s) Included / Fan Specifications
    Front Fan

    • FAN : 12V 0.1A
    • 800rpm ± 10%
    • Power Connector: IDE 4-PIN
    • Hydraulic Bearing
      Rear Fan
    1. FAN : 12V 0.1A
    2. 800rpm ± 10%
    3. Power Connector: Fan 3-PIN
    4. Hydraulic Bearing

13. I/O Connectors

Certification

This mark, designed by Zalman, indicates product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.

Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems). www.zalman.com.

References

• zalman.com
• ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>