smeg SAI613B Induction Cooktops Instruction Manual

INSTRUCTION MANUAL
INDUCTION COOKTOPS
SAI613B/SAI714B
SAI915B

SAFETY

Precautions before usage

• Unpack all the materials.
• The installation and connecting of the appliance have to be done by approved specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors.
• To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
• This domestic appliance is exclusively for the cooking of food, to the exclusion of any other domestic, commercial or industrial use.
• Remove all labels and self-adhesives from the ceramic glass.
• Do not change or alter the appliance.
• The cooking plate can not be used as freestanding or as working surface.
• The appliance must be grounded and connected conforming to local standards.
• Do not use any extension cable to connect it.
• The appliance can not be used above a dishwasher or a tumble-dryer: steam may damage the electronic appliances.
• The appliance is not intended to be operated by means of external timer or separate remote control system.

Using the appliance

• Switch the heating zones off after using.

• Keep an eye on the cooking using grease or oils: that may quickly ignite.

• Be careful not to burn yourself while or after using the appliance.

• Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan.

• Magnetically objects (credit cards, floppy disks, calculators) should not be placed near to the engaged appliance.

• Do not place any metallic object except heating containers. In case of untimely engaging or residual heat, this one may heat, melt or even burn.

• Never cover the appliance with a cloth or a protection sheet. This is supposed to become very hot and catch fire.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in
  a safe way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.

Precautions to prevent damage tothe appliance

• Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage the ceramic glass.
• Sand or other abrasive materials may damage ceramic glass.
• Avoid dropping objects, even little ones, on the vitroceramic.
• Make sure that the ventilation of the appliance works according to the manufacturer’s instructions.
• Do not hit the edges of the glass with saucepans.
• Do not put or leave empty saucepans on the vitroceramic hobs.
• Sugar, synthetic materials or aluminium sheets must not contact with the heating zones. These may cause breaks or other alterations of the vitroceramic glass by cooling: switch on the appliance and take them immediately out of the hot heating zone (be careful: do not burn yourself).
• WARNING: Danger of fire: do not store items on the cooking surface.
• Never place any hot container over the control panel.
• If a drawer is situated under the embedded appliance, make sure the space between the content of the drawer and the inferior part of the appliance is large enough (2cm). This is essential to guaranty a correct ventilation.
• Never put any inflammable object (ex. sprays) into the drawer situated under the vitroceramic hob. The eventual cutlery drawers must be resistant to heat.

Precautions in case of appliance failure

• If a defect is noticed, switch off the appliance and turn off the electrical supplying.
• If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the after sales service.
• Repairing has to be done by specialists. Do not open the appliance by yourself.
• WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.

Other protections

• Make sure that the container pan is always centred on the cooking zone. The bottom of the pan must have to cover as much as possible the cooking zone.
• For the users of pacemaker, the magnetic field could influence its operating. We recommend getting information to the retailer or of the doctor.
• Do not use aluminium or synthetic material containers: they could melt on still hot cooking zones.
• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

THE USE OF EITHER POOR QUALITY POT OR ANY INDUCTION ADAPTOR PLATE FOR NON- MAGNETIC COOKWARE RESULTS IN A WARRANTY BREACH. IN THIS CASE, THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED TO THE HOB AND/OR ITS ENVIRONMENT.

DESCRIPTION OF THE APPLIANCE

Technical characteristic

Total power
Energy consumption for the hob EChob| 7400 W
173 Wh/kg| 7400 W
165.7 Wh/kg| 6700 W
164.7 Wh/kg
Front left zone
Minimum detection
Nominal power
Booster power
Standardised cookware category
Energy consumption ECcw| Ø 160 mm
Ø 90 mm
1400 W
–
B
177.3 Wh/kg| 210 x 190 mm
Ø 90 mm
2100 W
2500 / 3000W
B
161.3 Wh/kg| 210 x 190 mm
Ø 90 mm
2100 W
2500 / 3000W
B
161.3 Wh/kg
Rear left zone
Minimum detection
Nominal power
Booster power
Standardised cookware category
Energy consumption ECcw| Ø 160 mm
Ø 90 mm
1400 W
2000 W
B
177.3 Wh/kg| 210 x 190 mm
Ø 90 mm
1600 W
1850 W
B
161.3 Wh/kg| 210 x 190 mm
Ø 90 mm
1600 W
1850 W
B
161.3 Wh/kg
Center zone
Minimum detection
Nominal power
Booster power
Standardised cookware category
Energy consumption ECcw| Ø 250 mm
Ø 110 mm
2300 W
3000 W
D
171.6 Wh/kg| |
Front right zone
Minimum detection
Nominal power
Booster power
Standardised cookware category
Energy consumption ECcw| 210 x 190 mm
Ø 90 mm
1850 W
1600W
B
161.3 Wh/kg| Ø 160 mm
Ø 90 mm
1100 W
1400 W
A
181.9 Wh/kg|
Rear right zone
Minimum detection
Nominal power
Booster power
Standardised cookware category
Energy consumption ECcw**| 210 x 190 mm
Ø 90 mm
2100 W
2500 / 3000W
C
177.6 Wh/kg| Ø 200 mm
Ø 90 mm
2300 W
3000 W
C
168.4 Wh/kg| Ø 250 mm
Ø 110 mm
2300 W
3000 W
D
171.6 Wh/kg

• The given power may change according to the dimensions and material of the pan.
  ** calculated according to the method of measuring performance (EN 60350-2).

Control panel

USE OF THE APPLIANCE

Sensitive touch
Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. In the case of a general use press only one key at the same time.
Display

0. 1…9
   U
   A
   E
   H
   P
   L
   U
   II| Zero
   Power level
   No pan detection
   Heat accelerator
   Error message
   Residual heat
   Power
   Locking
   Keep warm
   Stop&Go| The heating zone is activated.
   Selection of the cooking level.
   No pan or inadequate pan.
   Automatic cooking.
   Electronic failure.
   The heating zone is hot.
   The boosted power is activated.
   Control panel locking.
   Maintain automatically of 70°C.
   The hob is in pause.

Ventilation
The cooling system is fully automatic. The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level. The ventilation starts his high speed when the hob is intensively used. The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough.

STARTING-UP AND APPLIANCE MANAGEMENT

Before the first use
Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface.
Induction principle
An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone.
Of course the pan has to be adapted:

• All ferromagnetic pans are recommended (please verify it thanks a little magnet): cast iron and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms…
• Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic, stoneware,…

The induction heating zone adapts automatically the size of the pan. With a too small diameter the pan doesn’t work. This diameter is varying in function of the heating zone diameter.
If the pan is not adapted to the induction hob the display will show [ U ].
Power selection zone “SLIDER” and timer setting zone
Select the cooking zone. The display corresponding to the selected zone will be highlighted.
While the zone is activated (for a few seconds), you can adjust the power, either by sliding your finger on the slider.
To adjust the power of another cooking zone, wait until the previous zone is no longer activated (the highlighted display becomes normal).
Power selection zone “SLIDER” and timer setting zone

Starting-up

• Starting-up
  Action| Control panel| Display
  ---|---|---
  To start| Press key [ 0/I ]| [ 0 ] are blinking
  To stop| Press key [ 0/I ]| Nothing or [ H ]
• Start up / switch off a heating zone:
  Action| Control panel| Display
  ---|---|---
  Zone selection|  Press on the “SLIDER“ across from the desired zone| [ 0 ] and control light on
  To set (adjust the power)|  Slide on the “SLIDER“ to the right or to the left| [ 0 ] to [ 9 ]
  To stop| Slide to [ 0 ] on “SLIDER“  or press on [ 0 ]| [ 0 ] or [ H ] [ 0 ] or [ H ]

If no action is made within 20 second the electronics returns in waiting position.
Pan detection
The pan detection ensures a perfect safety. The induction doesn’t work:

• If there is no pan on the heating zone or if this pan is not adapted to the induction. In this case it is impossible to increase the power and the display shows [ U ]. This symbol disappears when a pan is put on the heating zone.
• If the pan is removed from the heating zone the operation is stopped. The display shows [ U ]. The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level set before.

After use, switch the heat element off: don’t let the pan detection [ U ] active.
Residual heat indication
After swittching off of a heating zone or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display.
The symbol [ H ] disappears when the heating zones may be touched without danger.
As far as the residual heat indicators are on, don’t touch the heating zones and don’t put any heat sensitive object on them. There are risks of burn and fire.

Boosterfunction and double booster
The Booster function [ P ] grants a boost of power to the selected heating zone.
If this function is activated the heating zones work during 10 minutes with an ultra high power.
Power is foreseen for example to heat up rapidly big quantities of water, like nuddles

• Start up / Stop the booster function:
  Action| Control panel| Display
  ---|---|---
  Zone selection| Press on the “SLIDER“ across from the desired zone| [ 0 ] and control light on
  Start up the booster| Slide on the “SLIDER“| [ 0 ] to [ P ]
  Stop the booster| Slide on the “SLIDER“| [ P ] to [ 0 ]
• Start up / Stop the double booster function:
  Action| Control panel| Display
  ---|---|---
  Zone selection| Press on the “SLIDER“ across from the desired zone| [ 0 ] and control light on
  Start up the booster| Slide on the “SLIDER“| [ 0 ] to [ P ]
  Start up the double booster| Slide on the “SLIDER“| [  and P ]
  Stop the booster| Slide on the “SLIDER“| [ P ] to [ 0 ]
• Power management:

The hole cooking hob is equipped by a maximum of power. When the booster function is activated, and not to exceed the maximum power, the electronic system orders to reduce automatically the power level of an other heating zone. The display is blinking on [ 9 ] during a few seconds and then shows the maximum of power allowed:

Timer
The timer is able to be used simultaneous with all heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone.

• Setting and modification of the cooking time :
  Action| Control panel| Display
  ---|---|---
  Zone selection|  Press on the “SLIDER“ across from the desired zone| [ 0 ] and control light on
  Select the power level| Slide on the “SLIDER“| [ 1 ] to [ 9 ]
  Select « Timer »| Press on the [ ]| [ 00 ]
  Set the tens| Press on the [ ]| [ 10, 20, 30, … ]
  Set the units| Slide on the “SLIDER“| [ 31, 32, 33, 34, 35, …]

The time is confirmed and the cooking starts.

• To stop the cooking time :
  Action| Control panel| Display
  ---|---|---
  Zone selection|  Press on the “SLIDER“ across from the desired zone| [ 0 ] and control light on
  Select « Timer »|  Press on the [ ]| [ 00 ]
  Desactivate « Timer »| Slide on the “SLIDER“ to [ 0 ]| [ 00 ]

• Automatic stop at the end of the cooking time:
  As soon as the selected cooking time is finished the timer displays blink [ 00 ] and a sound rings.
  To stop the sound and the blinking it is enough to press the key [ ].

• Egg timer function :
  Example for 29 minutes : Action| Control panel| Display
  ---|---|---
  Activate the hob| Press display [ 0/I ]| Zone control lights are on
  Select« Timer »| Press display [ CL ]| [ 00 ]
  Set the units| Slide on the “SLIDER“ to [ 9 ]| [ 0 fixed ] [ 9 blinking ]
  Valid the units| Press display [ 09 ]| [ 0 blinking ] [ 9 fixed ]
  Set the tens| Slide on the “SLIDER“ to [ 2 ]| [ 2 blinking ] [ 9 fixed ]
  Valid the tens| Press display [ 29 ]| [ 29 ]

After a few seconds the control light stops blinking.
As soon as the selected cooking time is finished the timer displays blink [ 00 ] and a sound rings.
To stop the sound and the blinking it is enough to press the display [ 00 ]. The hob switches off.
Automatic cooking
All the cooking zones are equipped with an automatic cooking device. The cooking zone starts at full power during a certain time, then reduces automatically its power on the pre-selected level.

• Start-up :
  Action| Control panel| Display
  ---|---|---
  Zone selection| Press display [ 0 ] selected| [ 0 ] and control light on
  Full power setting| Slide on the “SLIDER“ to [ 9 ]| Pass from [ 0 ] to [ 9 ]
  Automatic cooking| Re-press on display “SLIDER“ [ 9 ]| [ 9 ] is blinking with [ A ]
  Power level selection (for example « 7 »)| Slide on the “SLIDER“ to [ 7 ]| [ 9 ] pass to [ 8 ] [ 7 ] [ 7 ] is blinking with [ A ]
• Switching off the automatic cooking :
  Action| Control panel| Display
  ---|---|---
  Zone selection| Press [ 7 ] from  the zone| [ 7 ] blinking with [ A ]
  Power level selection| Slide on the “SLIDER“| [ 1 ] to [ 9 ]

Stop & Go function
This function brakes all the hob’s cooking activity temporarily and allows restarting with the same settings.

• Startup/stop the pause function :
  Action| Control panel| Display
  ---|---|---
  Engage pause| press [ II ] key during 2s| displays [ II ] in the heating zone displays pause control light is
  blinking pause control light is off
  Stop the pause| press [ II ] key during 2s press an other touch or slide on the “SLIDER“

Recall Function
After switching off the hob (0/I), it is possible to recall the last settings.

• cooking stages of all cooking zones (power)
• minutes and seconds of programmed cooking zone-related timers
• Keep warm function

The recall procedure is following:

• Press the key [0/I]
• Then simultaneously press the 2 zones back in less than 6 seconds.

The previous settings are again active.
« Keep warm » Function
This function allows to reach and maintain automatically a temperature of 70°C.
This will avoid liquids overflowing and fast burning at the bottom of the pan.

• To engage, to start the function « Keep warm » :
  Action| Control panel| Display
  ---|---|---
  To engage| press the slider between [ 0 ] and [ 1 ]| [ U ]
  To stop| slide on the “SLIDER“| [ 0 ] to [ 9 ] or [ H ]

Control panel Locking
To avoid modification of the setting of the cooking zones , in particular during cleaning, the control panel can be locked (with exception to the On/Off key [ 0/I ]).

• Lock :
  Action| Control panel| Display
  ---|---|---
  Start| press on key [ 0/I ]| [ 0 ] or [ H ] on displays
  Hob locking|  press on key [ ll ] and keep your finger on this key, with your other
  finger press 3 times key [ ]| [ L ] on displays
• Unlock :
  Action| Control panel| Display
  ---|---|---
  Start| press on key [ 0/I ]| [ L ] on displays
  In the 5 seconds after start:
  Unlocking the hob| press on key [ ll ] and keep your finger on this key, with your other
  finger press 3 times key [ ]| [ 0 ] or [ H ] on displays

COOKING ADVICES

Pan quality
Adapted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom.
Not adapted materials : aluminium and stainless-steel without ferromagnetic bottom, cupper, brass, glass, ceramic, porcelain.
The manufacturers specify if their products are compatible induction.
To check if pans are compatibles :

• Put a little water in a pan placed on an induction heating zone set at level [ 9 ].This water must heat in a few seconds.
• A magnet stucks on the bottom of the pan.

Certain pans can make noise when they are placed on an induction cooking zone. This noise doesn’t mean any failure on the appliance and doesn’t influence the cooking operating.

Pan dimension
The cooking zones are, until a certain limit, automatically adapted to the diameter of the pan.
However the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone.
To obtain the best efficiency of your hob, please place the pan well in the centre of the cooking zone.
Examples of cooking power setting
(the values below are indicative)

1 to 2| Melting Reheating| Sauces, butter, chocolate, gelatine
Dishes prepared beforehand
---|---|---
2 to 3| Simmering Defrosting| Rice, pudding, sugar syrup
Dried vegetables, fish, frozen products
3 to 4| Steam| Vegetables, fish, meat
4 to 5| Water| Steamed potatoes, soups, pasta, fresh vegetables
6 to 7| Medium cooking Simmering| Meat, lever, eggs, sausages Goulash, roulade, tripe
7 to 8| Cooking| Potatoes, fritters, wafers
9| Frying, roosting Boiling water| Steaks, omelettes, fried dishes Water
P| Frying, roosting Boiling water| scallops, steaks
Boiling significant quantities of water

MAINTENANCE AND CLEANING

Switch-off the appliance before cleaning.
Do not clean the hob if the glass is too hot because they are risk of burn.

• Remove light marks with a damp cloth with washing up liquid diluted in a little water. Then rinse with cold water and dry the surface thoroughly.
• Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided.
• Do not ever use any steam-driven or pressure appliance.
• Do not use any object that may scratch the ceramic glass.
• Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your ceramic hob or on the pan. Sliding rough saucepans will scratch the surface.
• Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent the surface being damaged.

WHAT TO DO IN CASE OF A PROBLEM

When the symbol [ E 4 ] appears:
I) The table must be reconfigured. Please implement the following steps:
Important : before you start:

• make sure there is no more pot on the hob
• take a pot with a ferromagnetic bottom and a minimum diameter of 16 cm
• disconnect the appliance from the grid by removing the fuse or turning the circuit breaker off
• start the procedure within 2 minutes after reconnecting the hob to the grid
• reconnect the table to the grid
• don’t use the [ O/I ] touch

II) First step: cancel the existing configuration

1. Press the touch B and hold down

2. With your other hand, press on the touch A during 2s. Released the touch A. A “beep” sound and the half slider lights. A double “beep” means an error occurred. If so, start again from item 1).

3. With your finger slide on the slider from right to left, always with your finger on the touch B. A “beep” sound if manipulation is succeeded, If isn’t so, start again from item 1).
   

4. Remove your fingers from the touch control, then push again on touch A during few seconds, until blinking [ E ] symbols appear.

5. Wait until [ E ] symbols stop blinking.

6. After few seconds, [ E ] are automatically transformed in [ C ]. The existing setup has been cancelled.

III) Second step: new setup

1. Take a ferromagnetical pot with a minimum diameter of 16 cm
2. Select a cooking zone with the slider.
3. Place the pot on the area to be set.
4. Wait until the [ C ] display becomes a [ – ]. The selected cooking zone is now configured.
5. Follow the same procedure for each cooking zone with a [ C ] display.
6. All the cooking zones are configured once all the displays are turned off.
   Please use the same pot for the whole procedure.
   Never put several pots together on the zones during the setup-process.

If [ E 4 ] displaying remains, please call the customer care
The hob or the cooking zone doesn’t start-up:

• The hob is badly connected on the electrical network.
• The protection fuse cut-off.
• The looking function is activated.
• The sensitive keys are covered of grease or water.
• An object is put on a key.

The control panel displays [ U ]:

• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.

The control panel displays [ E ]:

• Disconnect and replug the hob.
• Call the After-sales Service.

One or all cooking zone cut-off:

•  The safety system functioned.
• You forgot to cut-off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level and breaking Automatic overheating

Continuous ventilation after cutting off the hob:

• This is not a failure, the fan continuous to protect the electronic device.
• The fan cooling stops automatically.

The automatic cooking system doesn’t start-up:

• The cooking zone is still hot [ H ].
  The highest power level is set [ 9 ].

The control panel displays [ L ]:

• Refer to the chapter control panel locking page.

The control panel displays [ U ]:

• Refer to the chapter “Keep warm“.

The control panel displays [ II ]:

• Refer to the chapter “Pause“.

The control panel displays [ ] or [ Er03 ] :

• An object or liquid covers the control keys. The symbol disappear as soon as the key is released or cleaned.

The control panel displays [ E2 ] :

• The hob is overheated, let it cool and then turn it on again.

The control panel displays [ E3 ] ou [ E7 ] :

• The pan is not adapted, change the pan.

The control panel displays [ E6 ] :

• Defective network. Control the frequency and voltage of the electrical network.

The control panel displays [ E8 ] :

• The air inlet of the ventilator is obstructed, release it.

The control panel displays [ E C ] :

• Configuration error. Set the table again, referring to the chapter “The [E 4] appears.”

If one of the symbols above persists, call the SAV.

ENVIRONMENT PRESERVATION

• The materials of packing are ecological and recyclable.
• The electronic appliances are composed of recyclable, and sometimes harmful materials for the environment, but necessary to the good running and the safety of the appliance.
• **** Don’t throw your appliance with the household refuses
• Get in touch with the waste collection centre of your commune that is adapted to the recycling of the household appliances.

INSTALLATION INSTRUCTIONS

The installation comes under the exclusive responsibility of specialists.
The installer is held to respect the legislation and the standards enforce in his home country.
How to stick the gasket:
The gasket supplied with the hob avoids all infiltration of liquids in the cabinet.
His installation has to be done carefully, in conformity of the following drawing.

Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection sheet (3).

Fitting – installing:
The cut out sizes are:

• Ensure that there is a distance of 50 mm between the hob and the wall or sides.
• The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob.
• The piece of furniture or the support in which the hob has to be fit, as well as the edges of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C.
• The mural rods of edge must be heat-resisting.
• Not to install the hob to the top of a not ventilated oven or a dishwasher.
• Guarantee a space of 20 mm under the bottom of the hob casing to ensure a good air circulation of the electronic device.
• If a drawer is placed under the hob, avoid to put into this drawer flammable objects  (for example: sprays) or not heat-resistant objects.
• Materials often used to make worktops expand on contact with water. To protect the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the  supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces.
• The distance between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. In case of absence of instructions respect a minimumdistance of 760 mm.
• The connection cord should be subjected, after building, with no mechanical constraint, such for example of the fact of the drawer.
• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

ELECTRICAL CONNECTION

• The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously.
• Protection against the parts under tension must be ensured after the building-in.
• The data of connection necessary are on the stickers place on the hob casing near the  connection box.
• The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact opening of at least 3 mm.
• The electrical circuit must be separated from the network by adapted devices, for example: circuit breakers, fuses or contactors.
• If the appliance is not fitted with an accessible plug, disconnecting means must be incorporated in the fixed installation, in accordance with the installation regulations.
• The inlet hose must be positioned so that it does not touch any of the hot parts of the hob or even.

Caution!
This appliance has only to be connected to a network 230 V~ 50/60 Hz.
Connect always the earth wire.
Respect the connection diagram.
The connection box is located underneath at the back of the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the cover.
CONNECTION OF THE HOB FOR :

Mains| Connection| Supply cord| Supply cord| Circuit braker
---|---|---|---|---
230V~  50/60Hz| 1 Phase + N| 3 x 2,5 mm²| H 05 VV – F
H 05 RR – F| 25 A
400V~  50/60Hz| 2 Phases + N| 4 x 1.5 mm²| H 05 VV – F
H 05 RR – F| 16 A

• calculated with the simultaneous factor following the standard EN 60 335-2-6

Caution! Be careful that the cables are correctly engaged and tightened.
We cannot be held responsible for any incident resulting from incorrect connection or  which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection.

Warranty

THIS WARRANTY IS VALID IN AUSTRALIA ONLY
Note: Please complete the following details when you have unpacked the product and retain this card with the purchase invoice or sales docket.
Warranty:
This product is covered by a Warranty in addition to all rights available to you by statute.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The Warranty is for a period of two years (24 months) from the date of purchase for Parts and Labour, however, Dishwashers will have a 10 Year Parts and Labour Warranty on the Electric Wash Motor.
Refrigeration appliances will have an additional three years (36 months) Warranty, after the initial 24 months, for Parts only on the Sealed System eg; compressor, condenser, evaporator, filter dryer and pipe work, subject to the following conditions;
The conditions mentioned above are;

1. that the purchaser carefully follows all instructions packed with the product;
2. that the purchaser carefully follows the installation instructions provided and complies with the electrical wiring regulations, gas and/or plumbing codes;
3. that the purchaser carefully follows the instructions provided in the owner’s handbook relating to the proper use and care of the product and does not use the product for any purpose other than the Domestic, indoor use, for which it has been designed.
4. that the product was purchased and installed in Australia;
5. that this Warranty does not extend to:

a. Optional glass lids for hobs apart from claims which relate to mechanical or physical damage thereof at the date of purchase;
b. Light globes (with the exception of microwave oven globes);
c. Damage to ceramic glass caused by liquid or solid spillovers, lack of maintenance or impact. Please read the booklet explaining about liquids containing sugar;
d. Damage to the surface coatings caused by cleaning or maintenance using products not recommended by the owners handbook;
e. Defects caused by normal wear and tear, accident, negligence, alteration or misuse.
f. A product dismantled, repaired or serviced by any serviceperson other than an authorised employee or agent of Smeg Australia Pty Ltd;
g. The servicing of Freestanding Microwaves under this Warranty does not cover in home service and is limited to the appliance being taken to the nearest Service Agent.
h. The provision of service under this Warranty is limited by the boundary of the nearest agent’s area.
Travelling cost incurred for service outside this area is not covered by this Warranty and will incur commercial cost to be paid by the customer regulated by the number of kilometres travelled beyond the service area.

For service, please contact your local Smeg Australia Pty Ltd office or dealer/retailer from whom you purchased the product. If you are unable to establish the date of purchase, or if the fault is not covered by this Warranty, or if the product is found to be in working order, you will be required to bear all service call charges.

Smeg Australia Pty Ltd, 2 – 8 Baker Street, Banksmeadow NSW 2019 (www.smeg.com.au)
ABN No.33 146 901 082. ACN No.146 9––01 082

Smeg Australia Pty Ltd

Sydney Head Office| 02 8667 4888
Smeg Service| 02 8667 4833
Smeg Spare Parts| 02 8667 4875
Smeg Melbourne| 03 9094 1999
Australia-wide distributors:
Newcastle| 02 4960 9266
Wagga Wagga| 02 6922 8600
Queensland| 07 3266 0444
Tasmania| 03 6334 8166
South Australia| 08 8346 1888
Western Australia| 08 9389 8000

Smeg Australia Pty Ltd is constantly seeking ways to improve the specifications, design and production of its products. Alterations take place continually. Whilst every effort is made to produce up-to-date literature, this brochure should not be regarded as an infallible guide to the current specifications, nor does it constitute an offer for the sale of any particular product. Product cutouts indicated in our literature are indicative only. Actual product only should be used to define cutout sizes. Distributors, agents and retailers are not agents of Smeg Australia and have no authority to bind Smeg Australia by any express or implied undertaking or representation.

Smeg Australia Pty Ltd, 2 – 8 Baker Street, Banksmeadow NSW 2019
ABN No.33 146 901 082. ACN No.146 9––01 082
www.smeg.com.au
xxxxx/0

Documents / Resources

| smeg SAI613B Induction Cooktops [pdf] Instruction Manual
SAI613B Induction Cooktops, SAI613B, Induction Cooktops, Cooktops
---|---

References

• Italian Kitchen Appliances | Smeg Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>