HDTV SUPPLY 4K PoE HDMI Over IP Splitter User Manual

October 30, 2023
HDTV Supply

HDTV SUPPLY 4K PoE HDMI Over IP Splitter

HDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-product-img

Product Overview

Brief Introduction

4kPOE HDMI over IP series product extends and distributes HDMI signal via Gigabit IP network. This product can work not only as a normal HDMI extender by CAT5/6 cable up to 120 meters but also could transmit video data over a switch, router, and other Ethernet devices. It can work in broadcast mode, and send video data from 1 sender to 253 receivers. Highlights of this series of products are the support of 4K@30Hz 4:4:4 video, 5.1ch/7.1ch/DTS/Dolby audio, and ultra-low latency <50ms, which meet high-end customer requirements. Furthermore, UART / IR / external Audio all could be transmitted to help customers build complex commercial systems.

Features

  • Resolution up to 4K@30Hz 4:4:4, video no-loss
  • Ultra-low latency <50ms
  • Support HDMI audio 2CH/5.1CH/7.1CH/DTS/Dolby format
  • Support PoE(802.3AF)power supply, improve system robustness
  • Support maxim 1 sender to 253 receivers
  • Bi-direction UART bypass
  • Reverse IR bypass
  • External stereo audio channel (supported by HSV622)

Specifications

item Description
Power PoE(802.3AF)or 12V1A DC
HDMI format HDMI1.4, HDCP
HDMI audio format 2ch/5.1ch/7.1ch/DTS/Dolby
Ethernet Interface RJ45 Gigabit Ethernet
Resolution supported 4K@30Hz

1080p@60Hz/ 1080p@50Hz / 1080p@30Hz

720p@50Hz / 720p@60Hz / 480p@60Hz

External Audio Interface

( Optional)

| 3.5mm L/R jacket
IR frequency| 38KHz – 56KHz
UART Baudrate| 115200bps/9600bps/4800bps
Working Mode| Point to Point/Point to Multi-Point/Cascade
Transmission distance| Point to Point: CAT5e 100m/CAT6 120m

Cascade: maxim 20km

Working Temperature| 0°C – 40°C
Working Humidity| 20% ~ 90% RH(Non-condensing)

Hardware Description

Sender Front Panel

HDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-1

ID Type Description
POWER LED Light on: Power on
LAN TX Input / Output GE LAN port, support PoE(802.3AF)
Link LED Light on: sender and receiver connected
Status LED Flash slow: system working correctly
Signal LED Flash fast: system working abnormally

Light on: video transmission correct

▲IR| Output| Connect to IR emitter

Back Panel

HDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-2

ID Type Description
RS232 Input / Output Bypass bi-direction RS232 data to/from
IN Input receiver. Support baudrate 4800,9600,115200

Stereo audio input interface. When this port is connected, the receiver side HDMI audio and audio output will be the same as this input.

  • HSV622 support

  • HSV621 does NOT support

Reset| Button| Short press to restart the device
Input| Input| HDMI Input
5V-12V| Input| 5V 2A or 12V 1A DC power input

Receiver

Front Pane l

HDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-3

ID Type Description
POWER LED Light on: Power on
LAN RX Input / Output GE LAN port, support PoE(802.3AF)
Link LED Light on: sender and receiver connected
Status LED Flash slow: system working correctly

■ IR

|

Input

| Flash fast: system working abnormally Connect to IR receiver

Back Panel

HDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-4

ID Type Description
Rs232 Input/Output Bypass bi-direction RS232 data to/from
OUT Output sender. Support baudrate 4800, 9600,115200

Stereo output, same as HDMI

  • HSV622 support

| | * HSV621 does NOT support
Reset| Button| Short press to restart the device
Output| Output| HDMI output
OK-Button2| Button| Select/Confirm
EDID-Button1| Button| Short press to select function  update EDID
| | /change baud rate / show MAC Address / show IP

address When ”update EDID” shows, press OK- Buttont2 to confirm, The system EDID will update to the receiver-connected display’s EDID. When “baud rate” shows, press OK- Button2 to select the baud rate, then press Button1 to change the system baud rate.( MAC address and IP address can not be changed) Long press 3 seconds, directly update system EDID to the receiver connected displays’ EDID.

5V-12V| Input| 5V 2A or 12V 1A DC power input

INSTALLATION INSTRUCTIONS

  • Point to Point
  • Connection Diagram
  • Point to Multi-PointHDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-7
  • Cascade ModeHDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-9
  • Hybrid ModeHDTV-SUPPLY-4K-PoE-HDMI-Over-IP-Splitter-fig-10

Attention

  1. Please use the Gigabit switch in this system. A Fast Ethernet switch could not be used.
  2. Please do not plug or unplug the HDMI cable when the device is powered on, to avoid HDMI port components damage.
  3. Please do not plug or unplug the Ethernet cable when the device is powered on, to avoid RJ-45 port components damage.

FAQ

  • Q: Yellow light led off the LAN port is not lit?
    • A: 1) Check the connection of the network cable
    • 2) Change the short network cable to test
    • 3) Check whether the sender and receiver working correctly(Status LED flash slow)
  • Q: Green light led off the LAN port is not light
    • A : 1)Check whether the HDMI source is working correctly.
    • 2) Check whether the “signal” LED on the sender side is light on. If not, please check the HDMI
    • 3) Connection, HDMI cable, HDMI resolution setting
  • Q: No display on the screen connect to the receiver?
    • A: 1)Check the HDMI connection and HDMI cable between the receiver and screen.
    • 2) Check whether the sender and receiver working correctly(Status LED flash slow)
    • 3) Check whether the screen support 4K, and whether the output resolution is supported by the screen.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HDTV Supply User Manuals

Related Manuals