Hunter 19476 6 Light Chandelier Instruction Manual
- June 4, 2024
- Hunter
Table of Contents
Hunter 19476 6 Light Chandelier
INSTALLATION INSTRUCTIONS
Warning
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. One end of the threaded post (H) should be attached to the
mounting bracket (A) with a hex nut (G) in place. The other end should be
connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the
canopy loop
(E). Depending on the placement of your junction box the position of threaded
post (H) may need to be adjusted to allow the canopy to be flush with the
ceiling. Determine this by lifting mounting bracket (A) up to the junction box
and place canopy (D) over the canopy loop (E), so that it is flush with the
ceiling. Adjust the position of threaded post (H) on the mounting bracket (A)
so that the canopy (D) covers at least half of the exterior threads on the
canopy loop (E) while it is securely connected to threaded post (H). The
threaded post (H) can be adjusted by loosening hex nut (G) to allow movement
of threaded post (H) on mounting bracket (A). Once the ideal position of the
threaded post (H) is determined, tighten up the hex nuts (G) onto the threaded
post (H) just beneath the mounting bracket (A) to secure the threaded post in
place.
ASSEMBLING THE FIXTURE
Screw the bottom end of (P) into the hex connector (R) on the fixture. Slide
the cover (O) and cap (N) over rod (P)
and then secure them with the finial (M). There are 4 12-inch rods (J), and 1
6-inch rod (K) included for each fixture. Determine the correct number of rods
needed for proper hanging height. To lengthen the fixture, add additional
rods. To shorten the fixture, trim the wires to desired length. Leave at least
8 to 10 inches of wire in addition to the desired length and slide any excess
rods off the fixture’s wiring to discard. Keep in mind that you must use at
least one rod to hang the fixture. Thread the wires through the rods and pull
the wires until taut before connecting the rods together. Screw rod onto
threaded post (L) on the fixture. Pull the fixture wires through the canopy
loop ring (F), the top of canopy (D), and canopy loop (E). Screw the top rod
to canopy loop (E). Have a helper support the fixture’s weight and attach the
mounting bracket (A) to the junction box by securely tightening the mounting
screws (B).
CONNECTING THE WIRES
Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (C) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D). Lift the glass (S) and align the notches in the glass with the tabs in the lamp cup (T). Attach the glass by lifting and turning clockwise one third of a full turn of the glass until it stops. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now completed. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>