Mamibot W120-T Window Cleaning Robot User Manual

W120-T
User Manual

W120-T Window Cleaning Robot

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please contact the customer line.
✉ www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

Important Safety Instructions and Warning

Note! – Read all documents before using
The appliance is not to be used by children. Persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge may only use this appliance if they are supervised or have been given instruction about how to use it safely and understand what risks are involved.
Children should be supervised to ensure they do not play with the robot.
The appliance is for window cleaning with frames (frameless glass / windows cleaning is not applicable). Users should judge and use it safely on proper operation sites, and be responsible for all possible consequences.
Safety Information
Application of Power Adapter and Batteries.

• Use only the power adapter supplied with this device. Use of other type of power adapter will result in malfunction and / or danger.

• Please use the proper electric outlet and make sure no heavy objects are placed on the power adapter of power cord.

• Allow adequate ventilation around the adapter when using it to operate the device.
  Do not cover the power adapter with objects that will reduce cooling.
  Do not use the adapter in a high moisture environment. Never handle the adapter with wet hands.

• Connect the adapter to a proper power source. The voltage requirements are found on the adapter.

• Do not use broken adapter, power cord or plug. The plug must be removed from the receptacle before cleaning or maintaining the appliance. Do not unplug the power adapter by pulling on the power cord.

• Do not attempt to service the adapter. There are no service parts inside. Replace the whole unit if it is damaged or exposed to high moisture. Consult your Mamibot dealer for help and maintenance.

• The battery use in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, short contact, heat above 60° C (140°F), or incinerate.

• If you have to dispose of this old equipment, please take it to the local recycling centre for recycling electrical and electronic parts.

• Retain the safety and operating instructions for future reference.

• Follow all operating and use instructions.

• Do not expose your device to rain or excess humidity and keep it away from liquids (such as beverages, faucets, and so on).

• Avoid exposing your device to direct sunlight or intense light source and keep it away from heat source (such as radiators, space heaters, stoves, and so on).

• Do not place the device in the vicinity or strong magnetic fields.

• Keep the device in the vicinity of strong magnetic fields.

• Keep the device and accessories away from children.

• Product operating temperature: 0°C ~ 40°C (32°F ~ 104°F).

• Don’t use it on cracked glass or to clean other surface with uneven area as it may fall off due to insufficient suction power.

• The back-up battery must be replaced by the manufacturer or its service agent in order to avoid a hazard. The back-up battery must be removed and discarded according to local laws and regulations before disposal of the appliance. Please dispose of used batteries according to local laws and regulations.

• The appliance must be disconnected from the receptacle before removing the battery for disposal of the appliance.

• The appliance must be used in accordance with the directions in this instruction manual. Product manufacturer cannot be held liable or responsible for any damages or injuries caused by improper use.

Risk of Electric Shock!

• Always switch the device off before carrying out any cleaning or maintenance work.
• Never pull the power plug out of the socket by the power cord; instead, pull it out by the power plug itself.
• Never perform repairs on your device yourself. Repairs to electric devices may only be carried out by authorized customer service centre.
• Do not insert any pointed objects into the electric contacts.
• Do not change the contacts.
• Do not continue to operate the robot if the device itself or the power cord is damaged.
• Contact your local customer service in the event of damage.
• Do not clean the robot, the power cable in water or other liquids.
• Do not use the robot on damp ground or in places in which it can get into contact whit liquids or be immersed in water.
• Do not use the robot in hazardous areas such as open fireplaces, running showers or swimming pools.
• Make sure that you do not damage, bend or twist the power cord. Do not place any heavy objects on top of the cord. This could damage the power cord and cause a fire or electrical shock.

Warning

• Fasten the safety rope and tie to indoor fixture before operating the device.
• Check if the safety rope is broken or the knot is loose before operating the device.
• Set danger-warning area downstairs for no-balcony window and door.
• Battery shall be full-charged (Orange lamp ON) before using.
• Do not use it on rainy or moist days.
• Turn power on before you put device onto glass.
• Make sure the device can stick and stand on glass surface while put onto glass.
• Before turn power off, please hold the device.
• Do not use it on frameless glass.
• Make sure to put the cleaning pad on the bottom of the device correctly for no leakage.
• Do not spay or pour water onto the device.
• Prohibit children from using this device.
• Remove everything on the glass. Do not use on cracked glass. Reflective or coating glass might be slightly scratched due to dirt on the glass while operating.
• Keep hair, loose clothing, fingers, and all parts of body away from the openings and moving parts.
• Do not use in area with existed flammable or combustible liquids, gas.

Scan QR Code for APP downloading from here
iOS System:
Requires iOS 7.0 or later. Compatible with iPhone, iPad, and iPod touch.
Android System:
Requires Android 4.3 or later, Bluetooth 4.0 or later.
Notes:
Make sure the W120-T is switched on before connecting; If it is not connected successful, turn off the APP from device background, try again later.

https://play.google.com/store/apps/details?id=com.timyerc.iglassbot
https://play.google.com/store/apps/details?id=com.timyerc.iglassbot

Product Description & Parameters

Product Diagram

Product Parameters

About The Robot

Model No.| W120-T| Rated Voltage| 24 V DC
Rated Power| 75 W| Noise Level| About 65 Db
Battery Capacity| 600 mAh| Charging Time| About 1 h
Dimension| 25 x 25 x 10 cm| Net Weight| 1.35 kgs
Cleaning Speed| About 2.5 min / m2| |
Adapter

Input| AC 100-240 V 50 / 60Hz 2.0 A| Output| 24 V / 3.75 A

What’s in the Package?

Remote Control

| Automatically “Z” Type Cleaning| | Manual Move UP
---|---|---|---
| Automatically “N” Type Cleaning| | Manual Move Down
| From “Z” to “N” Cleaning| | Manual Move Right
| No Use Yet| | Manual Move Left
| No Use Yet| | Start Cleaning Choose “Z” or “N” Type automatically
| Stop Cleaning| | Stop / Restart

It is 2.4G wireless remote control, which can control your robot within maximum 15 meters away from any direction.

Installation

Assemble the Adapter

1. Connect DC plug (End A) of Power Adapter with extension cable (End B), as above1.
2. Connect End C to the robot power socket, screw the connector until it’s tightly locked2.

Fix the Safety Rope

1. Plug in the safety lock into the lock hole turn the safety lock clockwise around the lock hole till the indicator turns green. Note: W120-T can only be used when the indicator is in green.
2. Tie the other end of the rope to indoor fixture securely.

Attach Cleaning Pad

1. Choose the proper cleaning pad for your window.
2. Attach the cleaning pad to W120-T bottom properly, the pad should not cover driving treads or edge sensor5.
3. Spray 5 times of cleaning solution to the upper and lower side of W120-T,6 wipe the bottom after spraying7.

Connect to Power Supply
Plug in W120-T
Important Notes:
Be sure your W120-T is always connected to AC power supply while working. Don’t use it if the backup battery is lack of power, use it after full charging. Take off your W120-T asap, if the power supply is cur or unplugged accidently.

Operate W120-T

On/Off Button

1. Power On/Off button – Press for 2 seconds to turn on/off your W120-T.
2. Press the On/Off button once to start or stop the W120-T when it is placed on window.

Start Your W120-T

1. Press the On/Off button for 2 seconds to turn on your W120.
2. Place your W120-T on glass, press again the On/Off button to start.
3. You can also start it from your remote control “START” button.

Caution: Before starting, make sure the edge of W120-T is 8 cm or more away from window frames or corners.

Use of Remote Control

| Automatically “Z” Type Cleaning| | Manual Move UP
---|---|---|---
| Automatically “N” Type Cleaning| | Manual Move Down
| From “Z” to “N” Cleaning| | Manual Move Right
| No Use Yet| | Manual Move Left
| No Use Yet| | Start Cleaning Choose “Z” or “N” Type automatically
| Stop Cleaning| | Stop / Restart

Take off W120-T after cleaning
W120 will return to its starting point automatically after cleaning is finished. There is beep warning when cleaning is completed.

1. Use remote control to move your W120-T to a reachable.
2. Press On/Off Button for 2 seconds to switch it off.
3. Grasp the handle and take it from the window.
4. Untie the safety rope after finishing cleaning. Put the device and its spare parts in dry condition for future use.

Use APP on Your Smartphone

1. Download App for your iOS / Android device (refer to page 2 to scan and download, or search for “glasnost” in your Appstore or google play).
2. Turn on BLUETOOTH on your cell phone, and open glasnost APP on your phone.
3. Click the BLUETOOTH ICON on your glasnost interface to search device, and connect your W120-T with your phone, you can control it through cell phone now.

Maintenance

Cleaning Pad Maintenance
Put your W120-T up-side-down, take off the cleaning pad and put it into cold water, wash the cleaning pad with detergent and dry it for refuse.
Note: wet cleaning pad is not suggested to be used as it may get your robot stuck when cleaning glass with heavy dirt.
Fan Maintenance
Put your W120-T up side-down, use a clean and dry cloth to wipe out dirt/debris on the fan.
Edge Sensors Maintenance
Put your W120-T up side-down, use a clean and dry cloth top wipe out dirt/debris of the sensors.
Driving Treads Maintenance
Put your W120-T up side-down, use a clean and dry cloth to wipe out dirt/debris on it.

Troubleshooting

or too wet.
2.Cleaning pad is too dirty or too wet.| 1.Change cleaning pad.
2.Clean the driving treads.
3.Use remote control to manually restart it.
Insufficient suction power.| Insufficient suction power.| 1.Check if the cleaning pad is attached properly, replace it correctly.
2.Check if there is any crack on the glass.
3.Check if the glass frames are with uneven area/rubber part. If there is uneven area or uneven rubber part on the glass, use remove control to operate the device manually and keep the W122-T away from the uneven area / uneven rubber part when cleaning.
The devices can’t be started after switched on, or works in irregular patterns.| Edge detection sensor.| 1.Remove the cleaning pad and reattach it making sure it is placed exactly withing its Velcro area and does not cover the edge detection sensors.
2.Open APP on your phone, connect it with the robot and find out if any RED indications on the APP interface means the edge sensors is malfunctioned.
3.Edge detection sensors failure, contact after-sales service.
Red indicator light flashes, buzzer beeps once/second| Improper connection of Power Supply.| Check if the plug is connected well, or the screws of the extension cables are placed tight.
Bot Red and Blue indicator lights flash| Hardware failure.| Contact after- sales service.
Remote control does not work.| 1.No battery inside or battery has low power.
2.Remote control is broken.| 1.Change the battery.
2.Replace the remote control with new one.
The device got stuck on glass frames.| Edge-detection misjudgement.| 1.Press STOP on remote control, move the device to reachable location first.
2.Pull the robot tightly to reachable location if you can’t remote control it.
Both Red and Blue Light on, no beeps.| The device is not sucking properly on window.| Put the device on window surface manually, make sure it sucks on the window properly.
The indicators will flash twice in use.| Edge sensor detects frameless glass.| It’s normal, if it is cleaning frameless glass.
Squeaky sound when it’s in use.| Glass is too dry, or edge detection sensors are too dirty.| 1. Spray a little bit of water on the cleaning cloth.
2. Clean the edge detection sensors and operate again.
The device doesn’t return to Starting Point
after cleaning.| The glass surface’s friction index is
different.| Use remote control to direct the device return to reachable location.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

• Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.

• Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).

• Natural wear and aging of consumables or components during use (such as batteries, etc.).

• Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate
  polarity of this voltage, chemical processes such as used power supplies, etc.

• If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

EU Declaration of Conformity

** This appliance complies with the European Directives 2014/30EU, 2014/35/EU, and 2014/53/EU.
WEEE
** The symbol on this appliance indicated that this appliance may not be treated as household waste. Instead it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environment regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this appliance, please contact your local city office, your household and waste disposal service or the shop where your
purchased the appliance.

References

• Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
• alza.at
• Alza | Alza.co.uk
• alza.de
• alza.hu
• alza.sk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>